Allo RemoteControl NICE HSCU2W Instructions Manual

Allo RemoteControl NICE HSCU2W Instructions Manual

Advertisement

NICE HSCU2W, HSCU2C, HSCU2GW, HSCU2GC

Setting up the system components for configuration:

Since the system components communicate wirelessly, it is best to configure the system first on the
bench and only then locate and install the devices. For control panels which also have electrical
connections, proceed as follows:
1) configure the wireless devices on the bench;
2) mount all devices;
3) make the electrical hookup. To avoid errors, malfunctions and reception failures, proceed as follows:
a) Place all products on the bench with their packaging open;
b) Insert the "SIM" card for the GSM version (see figure 10); Caution - the SIM card's PIN must be
cancelled, along with any messages, contacts and other resident or saved information. Caution - 3G
SIM cards are not compatible.
c) Power up the control panel and program it - "Alarm system programming");
d) Insert the batteries into the devices so that the control panel can acquire them one by one;
e) Test the operation of the various devices;
f) Place the control panel in its intended location (do not mount it there yet);
g) Place the other devices in their intended positions (again, without mounting them yet);
h) Check that every device has sufficiently wireless reception to operate (see "Testing the control
panel"); In GSM models, check that there is sufficient reception:
i) Now install all devices in place; The following paragraphs describe the installation of the control
panel (all models) and the electrical hookup of wired versions.

Preliminary checks before installation and limitations on use:

Before proceeding with installation, check the condition of the product, suitability of the selected model
and conditions of the intended installation environment.
• Check that all conditions fall within the "limits of use" and "technical characteristics".
• Check that the installation location is compatible with the overall clearance of the product.
• Check that the mounting surface is solid, so that the device is mounted securely and is protected
against impact.
• Install the control panel at least 1 m off the ground. • the product may only be used with Nice Home
Security system devices
Visit our website: www.Alloremotecontrol.com
INSTRUCTIONS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NICE HSCU2W and is the answer not in the manual?

Questions and answers

Summary of Contents for Allo RemoteControl NICE HSCU2W

  • Page 1 INSTRUCTIONS NICE HSCU2W, HSCU2C, HSCU2GW, HSCU2GC Setting up the system components for configuration: Since the system components communicate wirelessly, it is best to configure the system first on the bench and only then locate and install the devices. For control panels which also have electrical connections, proceed as follows: 1) configure the wireless devices on the bench;...
  • Page 2 Installation: All control panel models are fitted with system memory boards. During programming, the card stores the system parameters (excluding voice messages recorded by the installer or user) and can be transferred from one control panel to another. Before removing or inserting the board make sure that the control panel is off and not powered. Some control panel models (models HSCU2GC and HSCU2G) are equipped with a GSM telephone dialler.
  • Page 3 Connections on the HSSOC siren: To connect the siren with the control panel, refer to Table 4 and figure 27A if the inputs are set as N.C. or 27B if the inputs are set as balanced Telephone line connection: Connect the phone line to connector (b) on the control panel, see fig. 6A and 6B on page 11. * Note (fig. 23 and 24) - The adapters are not included.
  • Page 4 Visit our website: www.Alloremotecontrol.com...
  • Page 6 Visit our website: www.Alloremotecontrol.com...
  • Page 7 Visit our website: www.Alloremotecontrol.com...
  • Page 8 Visit our website: www.Alloremotecontrol.com...

This manual is also suitable for:

Nice hscu2cNice hscu2gwNice hscu2gc

Table of Contents