Table of Contents
Advertisement
█ Bluetooth
®
Pairing cannot be done.
• Check the Bluetooth
• The device is out of the 10 m communication range. Move
the device nearer to the system.
The device cannot be connected.
• The pairing of the device was unsuccessful. Do pairing again
(
8).
• The pairing of the device has been replaced. Do pairing
again (
8).
• This system might be connected to a different device.
Disconnect the other device and try connecting the device
again.
• The system may have a problem. Switch off the system and
then switch on again.
The device is connected but audio cannot be heard
through the system.
• For some built-in Bluetooth
audio output to "SC-TMAX40" manually. Read the operating
instructions of the device for details.
Playback during Multi Connect is not working or no
sound.
• Restart the app of the device.
• The control of the device was not switched successfully.
Disconnect the existing connected devices and try again.
Sound from the device is interrupted.
• The device is out of the 10 m communication range. Move
the device nearer to the system.
• Remove any obstacle between the system and the device.
• Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.) are
interfering. Move the device nearer to the system and
distance it from the other devices.
█ Radio
Sound is distorted.
• Use an optional FM outdoor antenna. The antenna should
be installed by a competent technician.
A beat sound is heard.
• Switch off the TV or move it away from the system.
• Move mobile telephones away from the system if the
interference is apparent.
█ Unit displays
"--:--"
• You connected the AC mains lead for the first time or there
was a power failure recently. Set the clock.
• Track play time is more than 99 minutes.
"ADJUST CLOCK"
• The clock is not set. Adjust the clock.
"ADJUST TIMER"
• The play timer is not set. Adjust the play timer.
"AUDIO UNSUPPORTED"
• The signal format or frequency is not supported.
• This system does not support bitstream signals. Change the
digital audio output setting on the external equipment to
PCM.
• This system supports sampling frequencies of 32 kHz,
44.1 kHz, 48 kHz, up to 96 kHz. Select only the supported
sampling frequencies on the connected equipment.
• Try connecting the external equipment by using the auxiliary
input.
"AUTO OFF"
• The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button.
16
device condition.
®
devices, you have to set the
®
"DEVICE CONNECTED FULL"
• You have connected 3 Bluetooth
another device, disconnect one of the connected devices
and try again.
"ERROR"
• An incorrect operation was done. Read the instructions and
try again.
"F" / "F" ("" represents a number.)
• The protection circuit has been activated and the system
may be switched off automatically.
• Disconnect the AC mains lead and wait for a few seconds
before connecting it again. If the problem persists,
disconnect the AC mains lead and consult your dealer.
"NO DISC"
• You have not put in a disc.
"NO PLAY"
"UNSUPPORT"
• There is no album or track in the USB device.
• Examine the content. You can only play supported format.
• The files in the USB device can be corrupted. Format the
USB device and try again.
• The system may have a problem. Switch off the system and
then switch on again.
"NOT SUPPORT MULTI CONNECT"
• The Bluetooth
connection cannot be established.
®
Disconnect the existing connected devices and try again.
"NOT SUPPORTED"
• To use Karaoke effect in D-IN source, change the digital
audio output setting on the external equipment to PCM.
"PLAYERROR"
• An unsupported MP3 file has been played. The system will
skip that track and play the next one.
"REMOTE 1"
"REMOTE 2"
• The remote control and the unit are using different codes.
Change the code of the remote control.
– When "REMOTE 1" is shown, press and hold [OK] and
[
] on the remote control for a minimum of 4 seconds.
– When "REMOTE 2" is shown, press and hold [OK] and [<]
for a minimum of 4 seconds.
"USB A NO DEVICE"
"USB B NO DEVICE"
• The USB device is not connected. Examine the connection.
"USB OVER CURRENT ERROR"
• The USB device is drawing too much power. Disconnect the
USB device, switch off the system and then switch on again.
• Check the connection, it may be caused by a faulty USB
cable.
"VBR"
• The system cannot show the remaining play time for variable
bit rate (VBR) tracks.
devices. To connect
®
Advertisement
Table of Contents
