Pentair HYDROMATIC BV40 Installation, Operation & Parts Manual

SAFETY INFORMATION
Carefully read and follow all safety instructions in this
manual or on pump.
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of the
following signal words and be alert to the potential for
personal injury!
warns about hazards that will cause serious
personal injury, death or major property damage if ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The word NOTICE indicates special instructions which are
important but not related to hazards.
1. Read these rules and instructions carefully. Failure
to follow them could cause serious bodily injury and/or
property damage.
2. Check your local codes before installing. You must
comply with their rules.
3. Vent sewage or septic tank according to local codes.
4. Do not install pump in any location classified as
hazardous by National Electrical Code, ANSI/NFPA
80-1984 or the Canadian Electrical Code.
Hazardous voltage. Can shock,
burn, or kill. During operation the pump is in water.
To avoid fatal shocks, proceed as follows if pump needs
servicing:
Do not smoke or use devices that can generate sparks in a
septic (gaseous) environment.
5A. Disconnect power to outlet box before unplugging pump.
5B. Take extreme care when changing fuses. Do not stand
in water or put your finger in the fuse socket.
5C. Do not modify the cord and plug. When using the cord
and plug, plug into a grounded outlet only. When wiring
to a system control, connect the pump ground lead to
the system ground.
MOTOR, SWITCH, & CORD SPECIFICATIONS
Model Motor
Number HP
BV40AW1 4/10
BV40AD1 4/10
293 WRIGHT STREET, DELAVAN, WI 53115 WWW.HyDRomATIc.com
PH: 888-957-8677
© 2013 Pentair, Ltd. All Rights Reserved.
Motor
Full
Voltage Load Amps
115/1 12.6
115/1 12.6
InstallatIon, operatIon & parts Manual
BV40 Submersible Sewage
6. Be sure that construction
and access to septic
sumps conform with all
OSHA requirements.
7. Do not run the pump dry.
Dry running can overheat
the pump, (causing burns
to anyone handling it) and
will void the warranty.
8. The pump normally runs hot. To avoid burns when
servicing pump, allow it to cool for 20 minutes after
shutdown before handling it.
9. The pump is permanently lubricated. No oiling or
greasing is required in normal operation. for overhaul,
see instructions under "Service".
California Proposition 65 Warning
This product and related accessories contain
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.
DESCRIPTION
This submersible sewage ejector pump is designed for
residential wastewater removal, sewage applications,
sump drainage, dewatering and flood control. Units have
built in thermal overload protection with automatic reset.
The mechanical seal and bearings on the motor shaft are
permanently lubricated. Stainless steel hardware and a
heavy duty lift out handle allow for easy disassembly after
extended use.
NOTICE: This unit is not designed for applications involving
salt water or brine! Use with salt water or brine will void
warranty.
SPECIFICATIONS
Power supply required ............. See "Motor, Switch and Cord
Motor duty .............................................................Intermittent
Maximum Liquid Temperature .......................... 120°F (49°C)
Discharge Adapter ..................................................... 2" NPT
Individual Cord
Branch Circuit Length
Required (Amps) in ft. (m)
15 10 (3.0)
15 10 (3.0)
Ejector Pump
Specifications" chart below
Switch Setting
in inches (mm)
On Off
12-1/2 (317) 6-1/2 (165)
14-1/2 (368) 6 (152)
HYD056254461 (Rev. 02/21/13)
Discharge
Adapter
Size
2"
2"