Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Skandia Elevator SEH 50/18
Summary of Contents for Skandia Elevator SEH 50/18
- Page 1 ASSEMBLY INSTRUCTIONS H-LINE New generation SEH 50/18, 50/23 & 63/30...
- Page 3 Warranty A 2-year factory warranty from the day of delivery applies to all models of Skandia Elevator AB machinery. A condition of the warranty and any subsequent compensation is that Skandia Elevator AB is contacted and an agreement reached between the customer and Skandia Elevator AB on how any faults should be rectified.
-
Page 5: Table Of Contents
Elevator head ................................Back stop ..................................Bucket belt ..................................Buckets ....................................Centring of bucket belt ............................Adjusting the splash guard ........................... Elevator hood ................................Speed monitor ................................Inlet ......................................Water seal ..................................SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 6: Machine Overview
Elevator boot Leg spacer plate Clean out hatch Back stop with guard Inlet opening Elevator head Cover plate, inlet hopper Elevator hood Bucket belt Geared motor Elevator leg Outlet Service door Inspection cover SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 7: Safety Information
• Use protective gloves, helmet, steel-toed boots, ear defenders, protective goggles and high-vis vest when carrying out assembly, electrical connection, maintenance and operation of conveyor equipment. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 8: Electrical Safety
Inadequate maintenance may lead to personal injury or damage to the conveyor equipment and/or other equipment. It can also cause malfunctions or a reduction in capacity. WARNING! Read the separate maintenance instructions before taking the machine into service. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 9: Safety Decals
The machine is supplied with safety decals on delivery. They must not be removed or defaced. If a safety decal becomes damaged, you can order a new one free of charge from Skandia Elevator AB. Specify the part number of the decal. See the section below and the previous chapter Machine Overview. - Page 10 DEK3010 Warning for dust explosion! SKANDIA ELEVATOR - DEK3010 DEK3130 Warning, a maximum of 2 people = 200 kg/440 lbs may be on the platform and ladders simultaneously! SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30 SKANDIA ELEVATOR – DEK3130...
-
Page 11: Before Assembly
(B) from the downward to the upward side plate and then refit the rib plates (C) on both side plates, turn the rib plates as illustrated. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... - Page 12 IMPORTANT! Fit the elevator vertically within the specified tolerances (X and Y are vertical references). ± 15 mm ± 15 mm ± 15 mm ± 15 mm 90° ±0,5° 90° ±0,5° SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30...
-
Page 13: Connection Of The Machine
Applies to SEH 50/18-23:: NB! Inlet hopper (A) is designed for a descending leg side and extended inlet hopper (B) for an ascending leg side. SEH 63/30 SEH 50/18-23 M10x20 M8x16 SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 14: Connecting Another Machine To The Elevator
A conveyor can also be connected through a special outlet connection (F) directly to a connection hopper (D). Connecting the elevator to the conveyor Connect the elevator to the conveyor according to the assembly instructions for the respective conveyor. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 15: Assembling The Machine
Fit the belt alignment switch in the prepared location in the elevator boot and/or the elevator head. IMPORTANT! The bucket belt must be able to move 20 mm laterally in both directions without the belt alignment switch switching off the power. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 16: Elevator Legs
•If the elevator shall be equipped with explosion relief panels, read the instructions on the next page before fitting the legs. NB! Fit the leg with the service door on the ascending leg side at ground level. M10x35 SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 17: Explosion Relief Panels
6 metres spacing. Fit the dust curtain with explosion relief panel in the head. Use only explosion relief panels supplied by Skandia Elevator. WARNING! • Never stand in front of an explosion relief panel while the elevator is in operation. -
Page 18: Elevator Head
– Tension each cable using turnbuckles to 2.0 ± 0.5 kN. - The attachment of the cable must withstand a load of at least 8 kN. – Use an M10 shackle for mounting in the support frame. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 19: Back Stop
IMPORTANT! Ensure that the bucket belt is fitted with the thickest rubber coating (X) (3 mm) turned toward the slatted pulleys. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 20: Bucket Belt
(B) with nut and bolt. NB! If the hole pattern does not align, only the outer holes need to be used. Lubricate the threaded rods (C) and lower them into the sleeve profile (A). M10x35 M8x16 SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... - Page 21 Bucket belt tension must be checked and adjusted shortly after the elevator has been taken into service. Follow the description in the separate maintenance instructions. 50/18 = 3 pcs 50/23 = 4 pcs 63/30 = 5 pcs M10x35 SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30...
-
Page 22: Buckets
10 metres instead of a bucket. Use the same bolted joints as for the buckets. NB! The bucket belt can only be drawn upwards as the back stop prevents it from going down. Retighten the bucket belt as described in "Bucket belt" (12). SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 23: Centring Of Bucket Belt
If the bucket belt is running to the right on the slatted pulley in the elevator boot. Raise the slatted pulley (D) on the left-hand side plate by reducing the tension of the tensioning bolt (E) until the bucket belt is running centred. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 24: Adjusting The Splash Guard
Adjusting the splash guard Adjusting the splash guard 10 mm SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 25: Elevator Hood
Elevator hood Lift the parts of the hood into place (Alt. A) or slide them into place (Alt. B) fit and secure them. M10x35 Alt. A1 Alt. A2 Alt. B SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 26: Speed Monitor
• All electrical equipment is to be connected by a qualified electrician. See separate connecting directions for electronics. The speed monitor stops the elevator if the bucket belt slips. Fit the speed monitor in the holder that is fitted on the elevator boot. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... -
Page 27: Inlet
Prepare for and fit the inlet hoppers (A/B/C) or connection hopper (D) according to the chapter "Before connection" and "Connection, machine". SEH 63/30 SEH 50/18-23 M10x20 M8x16 Water seal IMPORTANT! When assembling outdoors, seal all the bolts, flanges and folds with silicone. SKANDIA ELEVATOR – SEH 50/18, 50/23 & 63/30... - Page 28 SKANDIA ELEVATOR AB KEDUMSVÄGEN 14, ARENTORP PHONE +46 (0)512 79 70 00 INFO@SKANDIAELEVATOR.COM S-534 94 VARA, SWEDEN FAX +46 (0)512 134 00 WWW.SKANDIAELEVATOR.COM...
Need help?
Do you have a question about the SEH 50/18 and is the answer not in the manual?
Questions and answers