Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Skandia Elevator SE 140
Summary of Contents for Skandia Elevator SE 140
- Page 1 MAINTENANCE INSTRUCTIONS L/I/H-LINE Elevators...
-
Page 3: Table Of Contents
Contents Thank you for choosing Skandia Elevator! Your conveyor system must be assembled correctly and maintained thoroughly if it is to operate satisfactorily. These maintenance instructions and the separate assembly instructions for each machine must be followed for the warranty to apply. -
Page 4: Safety Information
• Use protective gloves, helmet, steel-toed boots, ear defenders, protective goggles and high-vis vest when carrying out assembly, electrical connection, maintenance and operation of conveyor equipment. SKANDIA ELEVATOR... - Page 5 Certain sensors/switches are optional accessories only on certain machines. IMPORTANT! •Ensure the motor protection is set to the correct ampere setting for the motor. • Read the "Back stop" section in the elevator's assembly instructions before test starting the motor for the first time. SKANDIA ELEVATOR...
-
Page 6: Safety Decals
The machine is supplied with safety decals on delivery. They must not be removed or defaced. If a safety decal becomes damaged, you can order a new one free of charge from Skandia Elevator AB. Specify the part number of the decal. See the section below and the previous chapter Machine Overview. - Page 7 DEK3060 Warning for bucket belt! SKANDIA ELEVATOR – DEK3060 DEK3040 Warning for chain drive! SKANDIA ELEVATOR – DEK3040 DEK3070 Warning for rotating conveyor drive shaft! SKANDIA ELEVATOR – DEK3070 DEK3080 Warning for rotating elevator drive shaft! SKANDIA ELEVATOR – DEK3080...
-
Page 8: Maintenance
Elevator boot Clear the elevator boot from grain after a completed drying season and make sure there is nothing left that has started to grow before a new season starts. A. Clean out hatch SE-SEI-SEH New generation 50/18-63/30 SKANDIA ELEVATOR... -
Page 9: Transmission
The interval between changes can be doubled if synthetic oil is used. When operating in severe conditions such as high humidity, aggressive environment or large temperature variations, the oil must be changed more often. Clean the gear when changing oil. SKANDIA ELEVATOR... -
Page 10: Bucket Belt
Relieve the belt tensioner by releasing the ratchet one notch. NB! The belt tensioner must remain mounted on the bucket belt when the elevator is in operation. SKANDIA ELEVATOR... - Page 11 Centre the bucket belt IMPORTANT! Ensure the bucket belt is centred on the drive- and slatted pulley. Check how the bucket belt is running on the drive and slatted pulley. If it runs askew then it must be centred. SKANDIA ELEVATOR...
- Page 12 Applies to SEI, SEH and the new generation SEH: If the bucket belt is running to the right on the slatted pulley in the elevator boot. Raise the slatted pulley (E) on the left-hand side plate by reducing the tension of the tensioning bolt (F) until the bucket belt is running centred. SKANDIA ELEVATOR...
- Page 13 SEI & SEH New generation SEH SKANDIA ELEVATOR...
-
Page 14: Troubleshooting
• that the connecting channel and the elevator inlet for an elevator mounted in an elevator trench are the same size and that the angle of inclination is at least 45°. SKANDIA ELEVATOR... - Page 15 10 mm. 10 mm If the elevator stops unloaded Check: • that the speed monitor is correctly set or the power will be cut immediately after the elevator is started. Contact your supplier for help. SKANDIA ELEVATOR...
-
Page 16: Motor Stoppage
Valve is set correctly on delivery. If the setting has changed after delivery, it could cause leakage. Renew the setting in accordance with the instructions in the separate accessory assembly instructions, Replace actuator, which are available for download on the Skandia Elevator website. SKANDIA ELEVATOR... -
Page 17: Technical Specifications
30 t/h 40 t/h 60 t/h 80 t/h 100 t/h 120 t/h 150 t/h 200 t/h 250 t/h 300 t/h SE 140 32 m 29 m 30 m 27 m SEI 35/14 32 m 30 m 33 m 33 m... -
Page 18: Belt Tension - Bucket Belt
Wheat 700-800 Wholemeal 400-600 650-700 Oats 500-600 Mashed cereal 300-400 Powdered milk 500-600 Grain 600-700 Rape 600-700 Grass seed 120-200 Rice 700-800 Coffee 350-450 Corn 600-700 Fishmeal 550-600 Peas 600-700 Fish pellets 500-900 Beans 700-800 Powdered lime 800-990 SKANDIA ELEVATOR... -
Page 19: Sei
EP 630/4 Leg, width/depth 200 x 160 250 x 200 300 x 220 Plate thickness, head/boot 2.00 3.00 3.00 Plate thickness, legs 1.25 1.50 1.50 Plate thickness alternative, legs 2.00 2.00 2.00 Plate thickness, inlet hoppers 3.00 3.00 3.00 SKANDIA ELEVATOR... -
Page 20: Seh
2.3/3.0 4.0/5.7 4.0/5.7 Material thickness buckets Belt width Belt type/standard 630/4, 800/5, 1000/6 630/4, 800/5, 1000/6 Leg, width/depth 400/270 850/325 Plate thickness, head/boot 4.00 4.00 Plate thickness, legs 2.00 2.50 Plate thickness, inlet hoppers 3.00+8.00 Plastic 3.00+8.00 Plastic SKANDIA ELEVATOR... - Page 21 Bucket model/width Max buckets/m belt Buckets/m belt Bucket volume, net/gross litre 1.4/1.7 2.4/3.0 5.2/6.7 Material thickness buckets Belt width Belt type/standard 630/1 630/1, 800/1 630/1, 800/1, 1000/2, 1250/2 Leg, width/depth 300/230 350/250 430/310 Plate thickness, head/boot Plate thickness, legs SKANDIA ELEVATOR...
- Page 24 SKANDIA ELEVATOR AB KEDUMSVÄGEN 14, ARENTORP PHONE +46 (0)512 79 70 00 INFO@SKANDIAELEVATOR.COM FAX +46 (0)512 134 00 WWW.SKANDIAELEVATOR.COM S-534 94 VARA, SWEDEN...
Need help?
Do you have a question about the SE 140 and is the answer not in the manual?
Questions and answers