Subscribe to Our Youtube Channel
Related Manuals for Wiedenmann Terra Rake 170
Summary of Contents for Wiedenmann Terra Rake 170
- Page 1 Translation of original Operating Instructions Verticutting harrow Terra Rake 170 521.001 From equipment I.D. No. : Status : April 2017 521 99 01...
- Page 2 Am Bahnhof 89192 Rammingen declare under our sole responsibility that the product Verticutting harrow Terra Rake 170 to which this declaration refers, corresponds with the relevant basic safety and health requirements of the machinery directive 2006/42/EC. Rammingen, the 10.03.2015 Horst Wiedenmann...
- Page 3 Declaration of conformity Wiedenmann GmbH Am Bahnhof 89192 Rammingen hereby declare that the product Verticutting harrow Terra Rake 170 referred to by this declaration complies with the requirements of Machinery Directive 2006/42/EC. Rammingen, the 10.03.2015 Karl Wiedenmann (Place and date of issue)
- Page 4 Preface READ THESE OPERATING INSTRUCTIONS CAREFULLY to familiarise yourself with the correct way to operate and service your machine, and to prevent personal injury or damage to the machine. These operating instructions and the adhesive safety signs on your machine can also be obtained in other languages (your dealer can order these for you).
-
Page 5: Table Of Contents
TABLE OF CO N T E N T S Page * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * 1.0. -
Page 6: Safety
1.0. Safety Recognize safety information This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. Follow safety instuctions Carefully read all safety messages in this manual and on your machine safety sings. - Page 7 1.0. Safety Observe road traffic regulations Always observe llocal road traffic regulations when using public roads. Wear protective clothing Wear close fitting clothing and safety equipment appropriate to the job. Prolonged exposure to loud noise can cause impairment or loss of hearing.
- Page 8 1.0. Safety Guard and shields Keep guards and shields in place all the times. Ensure that they are in good condition and installed correctly. Always disengage the driveline, shut off engine and remove key before removing any guards or shields. Keep hands, feet and clothing away from moving parts.
- Page 9 1.0. Safety Use safety lights and devices Prevent collisions between other road users, slow moving tractors with attachments or towed equipment, and self- propelled machines on public roads. Frequently check for traffic from the rear, especially in turns, and use hand signals or turn signal lights.
- Page 10 1.0. Safety Remove paint before welding or heating Avoid potentially toxic fumes and dust. Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch. Do all work outside or in a well ventilated area. Dispose of paint and solvent properly.
-
Page 11: Safety Decals
1.0. Safety 1.1. Safety Decals Pictorial safety sings At several important places of this machine safety sings are affixed intendent to signify potenial danger. The hazard is identified by a pictorial in a warning triangle. An adjacent pictorial provides information how to avoid personal injury. -
Page 12: Safety Equipment
1.0. Safety 1.2. Safety instructions Apart from the information in these operating instructions, please also observe generally applicable safety and accident- prevention standards! During work operation, the user is responsible for the safety of third parties! During operation on public highways, the relevant traffic regulations must be observed! Before moving off, ensure that... -
Page 13: Assembly
2.0. Assembly 2.1. General Information Only attach the machine on firm, even ground. The Terra Rake is secured to the pallet by two transport feet when delivered. Once removed, the transport feet are no longer required and can be disposed of. For this work, please use your personal protective equipment (PSA) such as: gloves, goggles,... -
Page 14: Fitting The Drawbar
2.0. Assembly 2.4. Installing the drawbar Securely bolt the drawbar (A) to the bracket (B) on the basic unit using the three bolts (C). Secure the bracket (D) of the electrospindle (E) to the basic unit frame using the bolt (F). NOTE: Electro spindle (A) must NOT be energised. -
Page 15: Mounting The Strain Relief Kit
2.0. Assembly 2.5. Mounting the strain relief kit ATTENTION DANGER! The machine shall be set down on an even, secure surface for the mounting of the strain relief kit. Remove the screw, spring circlip and washer. The removed washer will be replaced. Secure spring holder I (A) on right with washer, spring circlip and screw as shown in... - Page 16 2.0. Assembly 2.5. Mounting the strain relief kit ATTENTION DANGER! The machine shall be set down on an even, secure surface for the mounting of the strain relief kit. Remove the screw, spring circlip and nut. The removed washer will be replaced.
-
Page 17: General Information
NOTE: After unpacking, check that all parts for the Terra Rake are present. The shipping company and Wiedenmann GmbH or the delivery company must be notified immediately in writing of any transportation damage and missing parts. All information, illustrations and specifications in these Operating Instructions are based on the latest information available at the time of... -
Page 18: Transportation With The Terra Rake
3.0. Transport 3.3. Transportation with the Terra Rake 3.3.1. Version with three-point linkage Raise the attached equipment with the tractor rear hydraulic system and secure against inadvertent lowering. 3.3.2. Version with drawbar Fully retract the electrospindle piston rod by activating the rocker switch. -
Page 19: Connecting To The Tractor
4.0. Connecting to the Tractor 4.1. General Information CAUTION DANGER! Secure the tractor against rolling away. Switch off the tractor and secure it against inadvertent switching on. 4.2. Mounting with cat.1 Mount the lower guide bolt on the outside in the lowest possible location bore. -
Page 20: Mounting With Cat.0
4.0. Connecting to the Tractor 4.3. Mounting with cat.0 Mount the lower guide bolt on the inside in the lowest possible location bore. You thus achieve a maximum lift travel. 1. Mount lower guide to bolt (A) and secure with linch pin. -
Page 21: Disconnecting From The Tractor
5.0. Disconnecting from the Tractor 5.1. General Information CAUTION DANGER! Switch off the tractor and secure it against inadvertent switching on. Secure the tractor against rolling away. When removing the machine, always set it down on a firm and even surface. 5.2. - Page 22 6.0. Before Initial Operation 6.1. General Information ACHTUNG GEFAHR! During work operation, the Beware of foreign bodies when verticut harrow user is working. responsible for the safety of Never reverse the verticut third parties. harrow while in the working When moving off, ensure that position.
-
Page 23: Before Initial Operation
6.0. Before Initial Operation 6.3. Setting the strain relief kit The strain relief kit reduces the tine penetration depth in synthetic turf (mandatory) or sensitive lawns (option). Setting for synthetic turf The strain relief kit must be mounted (i.e. mandatory) before the machine is used on synthetic turf. -
Page 24: General Information
7.0. Operation 7.1. General Information ATTENTION DANGER ! During work operation, the Use on artificial turf surfaces: verticut harrow user is Drive at a moderate speed. responsible for the safety of Avoid abrupt braking and third parties. acceleration or the synthetic When moving off, ensure that grass surface may shift or the immediate area of the... -
Page 25: Operation
7.0. Operation 7.3. Adjusting the working depth Starting operation Drive the tractor onto the surface to be worked on Lower the machine Start driving operation Operating speed 10 to 15 km/h [6.2-9.3 mile/hour] Pay attention to the effectiveness of the adjustment when performing work. -
Page 26: Maintenance
Shut down the that non-original parts that tractor and secure it against have not been delivered by accidental starting. Wiedenmann also have not been approved and released by After completion of the Wiedenmann. The installation maintenance work, remove and/or use of such products... -
Page 27: Lubricating - General Information
8.0. Maintenance 8.2. Lubrication – General Information The tractor engine must be switched off during all maintenance work. Where required, lubricate more often than specified. Keep all exposed machine parts, threaded spindles and guides slightly lubricated. Clean lubrication nipple before use. -
Page 28: Cleaning The Verticut Harrow
8.0. Maintenance 8.4. Cleaning the verticutting harrow Clean the verticutting tines on a regular basis. This lengthens the service life of the components and, in the process, you discover loose components, wear and areas of unwanted corrosion. NOTE: Do not bring plastic and sealing elements in contact with aggressive fluids (e.g. -
Page 29: Replacing The Spring Tines
8.0. Maintenance 8.5. Replacing the spring tines Loosen all hexagon nuts (A) of the faulty spring elements Remove the clamping sleeves (B) on the left and right of the axle. Pull the axle (C) outwards. Replace spring elements Insert axle (C) Tap the clamping sleeves (B) on the left and right into place. -
Page 30: Disassembly/Disposal
8.0. Maintenance 8.6. Disassembly / disposal ATTENTION DANGER ! Exercise care when Disassembly for disposal : disassembling. Place verticutting tines Please refer to the on firm ground. chapter "Safety measures" Disassemble verticutting and local safety tines, working from top regulations. to bottom. -
Page 31: Unauthorised Modification And Spare Part Manufacturing
8.0. Maintenance 8.7. Unauthorized conversion and spare part manufacture Conversion or modifications to the verticutting tines are permissible only after consultation with the manufacturer ! The use of original parts and accessories authorized by the manufacturer is in the interest of safety. -
Page 32: Equipment
9.0. Equipment 9.1. Scope of Delivery Basis unit with three-point linkage drawbar Operating instructions, transfer declaration with guarantee card. 9.2. Machine designs Version 1 Version 2 Verticutting harrow 1700 Attachment frame complete Cat.1 and O Drawbar The strain relief kit must be mounted (i.e. -
Page 33: Special Equipment
9.0. Equipment 9.3. Special equipment Strain relief kit 9.4. Attachment components Attachment Torro 7210 All information, illustrations and specifications in these Operating Instructions are based on the latest information available at the time of publication. We reserve the right to make design changes at any time without prior notification... -
Page 34: Technical Specifications
10.0. Technical Specifications 10.1. Technical Data Height up to lower pull rod connection (down) Height up to lower pull rod connection (up) Height up to middle of upper guide bar connection cat.0 Height up to middle of upper guide bar connection cat.1 Machine length E1 Machine length in the transport position 1770... - Page 35 10.0. Technical Specifications 10.1. Technical Data 521.25 All information, illustrations and specifications in these Operating Instructions are based on the latest information available at the time of publication. We reserve the right to make design changes at any time without prior notification...
-
Page 36: Metric Bolt And Cap Screw Torque Values
10.0. Technical Specifications 10.2. Metric bolt and cap screw torque values Property Class and Head Markings Property Class and Markings class 4.8 class 8.8 or 9.8 class 10.9 class 12.9 Size Lubricated * Dry ** Lubricated * Dry ** Lubricated * Dry ** Lubricated * Dry **... -
Page 37: Chassis Number
10.0. Technical Specifications 10.3. Chassis Number Enter the respective product identification no. in the space Wiedenmann D-89192 Rammingen provided below. Always quote Terra Rake 1700 this number when ordering spare parts or in case of warranty claims. 521.26 Fz. Id. Nr. _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ All information, illustrations and specifications in these Operating Instructions are based on the latest information available at the time of publication.
Need help?
Do you have a question about the Terra Rake 170 and is the answer not in the manual?
Questions and answers