Related Manuals for SmartRG SR616ac
Summary of Contents for SmartRG SR616ac
- Page 1 Quick Start Guide SR616ac This Quick Start Guide shows you how to set up and start using your new gateway.
-
Page 2: Installation
Installation 1. Connect one end of the included phone cable to the DSL port on the gateway and connect the other end to the wall jack. 2. Connect one end of an Ethernet cable to a LAN port of the gateway and connect the other end to your PC. 3. -
Page 4: Led Indicators
LED INDICATORS The LEDs on the front of the SR616ac gateway can help you understand the current state of your adapter. White Green Legend: White blinking Green blinking Action Explanation All LEDs except Feature enabled &/or working correctly those listed below... -
Page 5: Quick Gateway Configuration
QUICK GATEWAY CONFIGURATION Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small cir- cular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into the hole, press the Reset button for 1 second, and then release the button. -
Page 6: Configuring The Wan Manually
Configuring the WAN manually If the automatic connect process is unsuccessful, refer to the Advanced Setup > Layer 2 Interface WAN Service sections of the SmartRG SR616ac Gateway User Manual to manually establish a connection. - Page 7 WiFi Setup Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow the instructions for the applicable method. The default settings work for most situations. 1. In the left menu, click Wireless and then click 2.4 GHz Band...
-
Page 8: Wps Method
WPS Method If the device you wish to connect to the Internet via your gateway supports the WPS secure Wi-Fi connection method, follow these steps. 1. In the left navigation bar, click Wireless, then click the band that you want to configure, and then click Secur- ity. -
Page 9: Manual Method
Manual Method Set up your gateway’s parameters first, then follow these steps. 1. In the left menu, click Wireless and then the band that you want to configure. 2. Click Security and scroll down to the Manual Setup AP section. 3. -
Page 10: Additional Support
Record Your SR616ac Wi-Fi Settings Predefined wireless settings If you change the preset wireless settings WiFi network name (SSID) Network key (password) Additional Support If you require further instructions, please contact your local ISP Support. SMARTRG INC. ALL RIGHTS RESERVED. COPYRIGHT 2017 ©... -
Page 11: Important Safety Instructions
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. -
Page 12: Fcc Statements
FCC Statements FCC - Part 68 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom case of this equipment is a label that contains, among other information, a product identifier in the format US: VW7DL01ASR616A. - Page 13 If trouble is experienced with this equipment, for repair or warranty information, please contact SmartRG,Inc. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
- Page 14 FCC - Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 15 Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including inter- ference that may cause undesired operation of the device.
- Page 16 antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été...