How To Check The View Mode Using A Tact Switch - Samsung AM072/096/120/144FXVAFH Service Manual

How to check the view mode using a tact switch

AM072/096/120/192HXWA
K3 (Number of press)
1 time
K4
(Number of press)
1 time Outdoor unit model
2 times Target frequency (Compressor 1)
3 times Target frequency (Compressor 2)
4 times High pressure (MPa)
5 times
6 times Discharge temperature (Compressor
7 times Discharge temperature (Compressor
8 times IPM temperature (Compressor 1)
9 times IPM temperature (Compressor 2)
10 times CT sensor value (Compressor 1)
11 times CT sensor value (Compressor 2)
12 times Suction temperature
13 times COND OUT temperautre
14 times Temperature of liquid pipe
15 times TOP temperature (Compressor 1)
16 times TOP temperature (Compressor 2)
17 times
18 times EVI inlet temperature
19 times EVI outlet temperature
20 times
21 times
22 times
23 times
24 times
25 times Current frequency of the compressor
26 times Current frequency of the compressor
27 times Suction 2 temperature
28 times Address of master indoor unit
29 times Temperature of control box
When you install the product, optional function for outdoor unit must be set in compliance with installation conditions.
SW version, View mode 2 and address of the indoor unit, press and hold for three seconds to enter the K4.
(Information will be displayed in following order. Main-Hub-INV1-INV2 FAN1-FAN2-EEP-Automatically assigned address -
manually assigned address.)
View mode 2
K4
KEY operation
(Number of press)
1
TIME Main version
2
TIMES HUB version
3
TIMES Water HUB version
4
TIMES Inverter1 version
5
TIMES Inverter2 version
6
TIMES EEPROM version
The device receives
7
TIMES
automatic address
The device receives
8
TIMES
a manual address
8-14
KEY operation
Intialize (Reset) setting
KEY operation
Low pressure (MPa)
Water temperature
Main EEV 1 step
Main EEV2 step
EVI EEV step
HR EEV step
-
KEY operation
Main version
HUB version
Water HUB version
Inverter1 version
Inverter2 version
EEPROM version
The device receives
automatic address
The device receives
a manual address
(cont.)
Display on segment
Same as initial state
Display on segment
SEG 1
1 AM120FXW → Off, 1, 2
120 Hz → 1, 2, 0
2
3 120 Hz → 1, 2, 0
4 1.52 MPa → 1, 5, 2
0.43 MPa → 0, 4, 3
5
6 87 °C → 0, 8, 7
7 87 °C → 0, 8, 7
8 87 °C → 0, 8, 7
87 °C → 0, 8, 7
9
A
B
-42 °C → -, 4, 2
C
D -42 °C → -, 4, 2
E -42 °C → -, 4, 2
-42 °C → -, 4, 2
F
-42 °C → -, 4, 2
G
H -42 °C → -, 4, 2
I -42 °C → -, 4, 2
-42 °C → -, 4, 2
J
K 2000 steps → 2, 0, 0
L 2000 steps → 2, 0, 0
300 steps → 3, 0, 0
M
N 2000 steps → 2, 0, 0
O
120 Hz → 1,2,0
P
Q 120 Hz → 1,2,0
R -42 °C → -, 4, 2
When master indoor unit is not set → BLANK, N, D
S
When indoor unit No.1 is set as master indoor unit →0, 0, 1
T -42 °C → -, 4, 2
Display on Page
Page 1
Main
HUB
HUB2
INV1
INV2
EEPROM
AUTO
Indoor unit : "A","0"
MCU : "C","1"
MANU
Indoor unit : "A","0"
SEG2, 3, 4
2 A → 0, 2, 0
2 A → 0, 2, 0
-
Page 2
Version(ex. 1412)
Version(ex. 1412)
Version(ex. 1412)
Version(ex. 1412)
Version(ex. 1412)
Version(ex. 1412)
SEG1,2 SEG3,4
Adress(ex. 07)
SEG1,2 SEG3,4
Adress(ex. 15)
Samsung Electronics