Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ergolux ELSTANDWWBA
Summary of Contents for Ergolux ELSTANDWWBA
- Page 1 WHITE BOARD AND STANDING DESK ELSTANDWWBA...
-
Page 3: Safety And Warnings
SAFETY & WARNINGS • Read all instructions before use and retain this user guide for future reference. • Read all following safety precautions carefully before use. • Your equipment is intended for use in cool, dry conditions. You should avoid storage in extreme cold, hot or damp areas as this may lead to corrosion and other related problems. - Page 4 COMPONENTS Lay all components out on a clean floor and ensure all parts are included. If any pieces are missing, check all packaging thoroughly, then contact help.Kogan.com for assistance. 1 Feet (x2) 2 Left lifting column 3 Right lifting column 4 Supporting beam 5 Transmission rod 6 Left baffle...
- Page 5 Hardware list A M6 (x8) B M6 (x4) C Self-tapping D Self-tapping screw (x4) screw (x8) E M4 (x4) F M8 (x4) G Self-tapping screw (x10) Tools 5mm Allen key 4mm Allen key 2.5mm Allen key Spanner...
- Page 6 ASSEMBLY Step 1: Installing the feet. Attach the feet (1) to the lifting columns (2)(3) using the M6 screws (C) and tighten using the 4mm Allen key. A M6 (x8) 4mm Allen key...
- Page 7 Step 2: Installing the supporting beam. • Loosen screws on supporting beam (4) using the 4mm Allen key and adjust the supporting beam to your desired width. • Using the M8 screws (F) attach the supporting beam (4) to the lifting columns (2)(3) and tighten using the 5mm Allen key.
- Page 8 Step 3: Installing the transmission rod. • Use the spanner to loosen the nut on the transmission rod (5). • Insert the nut side of the transmission rod into the left lifting column (2). • Attach the transmission rod (5) to the right lifting column (3) by rotating it clockwise and use the 2.5mm Allen key to tighten screws on the transmission rod (5).
- Page 9 Step 4: Installing the side brackets. • Using M6 screws (B) attach the side brackets (8) to the lifting columns (2)(3) and tighten using the 5mm Allen key. Note: Ensure the handle is installed on the same side as the motor. •...
- Page 10 Step 5: Installing the desktop. • Adjust the support beam (4) and the transmission rod (5) to the appropriate length according to the width of the desktop • Attach the desktop with the self-tapping screws (G) using a drill or impact driver. •...
- Page 11 Step 6: Installing the baffles. • Twist open the connecting plates on the left and right baffles (6)(7). • Use the M4 screws (E) to attach the left and right baffles (6)(7) to the support beam and tighten using the 2.5mm Allen key. Note: Ensure the right baffle (7) is installed on same side at the motor.
- Page 12 Step 7: Installing the control box, headset and castors. • Attach the control box to the tabletop using the self-tapping screws (G). • Attach the handle to the tabletop using the self-tapping screws (C). • Attach the handset (10) to the desktop using the self-tapping screws (G). •...
- Page 13 Step 8: Connecting the control box. • Following the diagram below, connect the lifting column connector to the control box (9). • Connect the handset connector (10) to the control box (9). • Connect the power cord (14) to the power adapter (8). Power cord Lifting column Handset...
- Page 14 Step 9: Cable management. • Remove the adhesive backing and attach the supplied cable ties (E) to the underside of the tabletop. • Tidy up and secure all the cables in place using the cable ties (E). E Cable ties (x6) Attach Secure Remove...
- Page 15 Step 10: Install the magnet storage box. Attach the magnetic storage box (13) to the lifting column. Note: The maximum weight capacity is 0.8kg.
- Page 16 Step 11: Adjusting the angle of tabletop. • The tabletop can be adjusted to five different angles (0˚, 60˚, 70˚, 80˚, 90˚ • Press the handle and rotate the tabletop to the desired angle. • Release the handle ensuring the tabletop locks into position with an audible ‘click’. Note: Do not leave anything on the tabletop when adjusting the angle.
-
Page 17: Operation
OPERATION Handset Controls Button Description ▲ Raise the desk height ▼ Lower the desk height First user defined height position Second user defined height position Third user defined height position Memory button Alarm button Functions Adjusting the height: Press the ▲... -
Page 18: Setting Sensitivity Level
Stand up alarm: Pressing the “Alarm” button will enable the stand up alarm function. The LED will display After 2 seconds the LED display will flash. By default the stand up alarm timer is set to 45 minutes. Use the ▲... -
Page 19: Specifications
SPECIFICATIONS Column Stage Max. weight capacity 70kg (horizontality) Height range 760-1260mm Width range 900-1350mm Desktop angle range 0°, 60°, 70°, 80°, 90° Storage box weight 0.8kg... -
Page 20: Troubleshooting
TROUBLESHOOTING The following tips will help you detected and eliminate some common faults and errors. If the problem cannot be fixed or the fault is not listed below, please contact help.Kogan.com for support. Problem Solution No response after pressing and Check if all the cables be connected well. - Page 21 NOTES...
- Page 24 Need more information? We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com.
Need help?
Do you have a question about the ELSTANDWWBA and is the answer not in the manual?
Questions and answers