Softub 140 Owner's Manual
Hide thumbs
Also See for 140:
- Owner's manual (32 pages) ,
- User manual (20 pages) ,
- Assembly instructions manual (16 pages)
Subscribe to Our Youtube Channel
Related Manuals for Softub 140
Summary of Contents for Softub 140
- Page 1 Owners Manual & Water Treatment Guide Softub Canada 967 Falconbridge Road Sudbury, Ontario P3A 5K8 Telephone: (800) 668-8827 Fax: (800) 463-3845 E-mail: sales@softubcanada.com...
-
Page 2: Table Of Contents
Many of its unique features are patented. We are sure that you too will join the ranks of satisfied Softub customers. The Softub has been designed to be simple to operate. With a little care, it will give you many years of enjoyable, trouble-free use. -
Page 3: Safety Instructions
Use a properly grounded outlet of 110 Volt AC. Do not put Softub on floors or other surfaces that are not structurally strong enough to support a load of 125 lb/sq.ft. (611 kg/sq.m.) and/or on any floors or other surfaces that will not withstand exposure to water. -
Page 4: Manufacturer's Warnings
Equipment failure may also cause substantial water spillage. Care must be taken that the structure underneath the Softub will not warp or suffer damage in the event of a water spill. If located in a multiple floor structure, objects on the floor below should be protected in the event of a major spill. -
Page 5: Installation Instructions
You may place the Softub on any smooth surface (tile, concrete, wood, brick). Verify there are no sharp objects under the tub prior to set-up. Placing the Softub on grass or other vegetation may damage the Softub. If you need to step on grass or dirt to get to the Softub, we recommend the use of stepping stones to reduce the amount of dirt and debris entering the tub. -
Page 6: Set-Up Checklist
SET-UP CHECKLIST ________ 1. All Softub models come with locking straps. Be sure to place the safety straps in an “X” fashion under the tub prior to filling. ® ® ________ 2. Set the HydroMate beside the Softub on the same level surface. Align the hoses from the HydroMate with the fittings on the tub. -
Page 7: Operation
*Patent Pending Programming Ground Fault Circuit Interrupter (GFCI) The Softub cord is fitted with a ground fault circuit interrupter (GFCI), a very important safety feature. The GFCI shuts off the ® electricity immediately if there is a short in the cord or HydroMate . This plug fits conventional 110 Volt outlets found in homes. -
Page 8: Maintenance
Consult the water treatment section. Changing Water Empty the Softub and fill with clean water every 2-3 months or when it becomes cloudy and proper water chemistry does not clear it up. 1. Before draining tub, pour 250 ml of Swirl Away into water and circulate for 1 to 2 hours with the air control off. Also make sure that the thermostat is set to maximum temperature, this will allow the pump to run continuously. -
Page 9: Winterizing & Vacationing; Storing & Transporting; Filling & Draining
Winterizing and Vacationing If you are taking a vacation or leaving your Softub outdoors and unused for a week or more, you should leave the bi-fold lid ® ° on, air control valve closed and set the control dial on your HydroMate to 7, on P6 and earlier models to 100 F and on P7 models. -
Page 10: Water Treatment
In addition to important information about water treatment products and hot tub maintenance, we have featured details on the use of recommended water treatment products. Our goal is to help you get the most out of your Softub - to enjoy its fun, therapy and convenience. -
Page 11: Water Balance
3-5 ppm level. If you have any questions or concerns concerning Softub water treatment, please contact your local Authorized Softub Dealer. A Softub dealer can provide you with a complete water analysis and assist in designing an easy to follow water treatment program. -
Page 12: Water Treatment Trouble-Shooting Guide
WATER TREATMENT TROUBLE-SHOOTING GUIDE SYMPTOMS CAUSE SOLUTIONS Built-up of body oils and/or Add a few drops of an anti-foam concentrate. If Foaming chemicals problem persists, drain part or all of the water and refill pH/alkalinity out of balance Adjust pH and alkalinity, as necessary Adjust pH and alkalinity, as necessary pH/alkalinity out of balance Cloudy Water... -
Page 13: Trouble-Shooting
TROUBLE SHOOTING Problem: The tub is connected but nothing is working. Cause: The tub may be wired incorrectly. The GFCI only works if the wiring is in the orientation. Solution: 1. Consult an electrician to repair the circuit in question. Problem: Tub will not heat up to desired operating temperature. - Page 14 Problem: No LED temp display. ® Cause: Loss of power at wall switch or HydroMate . Solution: 1. Make sure that the unit is plugged into a 110 Volt outlet. 2. Test GFCI on the power supply cord. See instructions on page 5. 3.
- Page 15 B) Check the HydroMate for water at HydroMate side of hose connection or under the HydroMate . 4. Most tub leaks can be easily patched with a Softub vinyl repair kit available from your dealer (see instructions on repair kit). ®...
-
Page 16: Tub Squeezing
TUB SQUEEZING We have designed the Softub to be completely portable in every way possible. Because of its large diameter it would be next to impossible to roll it down the stairs and into your basement.. Therefore, we have developed a different method so that you can get it into your basement. -
Page 17: Year Limited Warranty
5 YEAR LIMITED WARRANTY Softub Canada warrants the Softub to be free of defects in materials and workmanship for five (5) full years from date of purchase. Any repairs required will be at the following costs to the customers. Tub, Bi-fold lid and LeatherTex...
Need help?
Do you have a question about the 140 and is the answer not in the manual?
Questions and answers