Avital 3100 Install Addendum

Install Addendum/Instalación Addendum
Programming System Features
The system features are pre-programmed to default settings and may need to be
changed to accommodate vehicle specific requirements and user preferences. To
change the system feature settings use the following procedure:
Important: Test the systems Ignition input, Door trigger input, Valet button, Status
LED, and siren for proper operation before proceeding.
1. Select a System Feature and required number of Valet button presses as
described in the following Features table.
2. Open a door, turn the key ON, and then OFF.
3. Press and release the Valet button to select the feature. After pressing and
releasing corresponding to the selected function, then press the Valet button
once more and hold it. The LED flashes and the siren sounds to confirm
the selection.
4. While still holding the Valet button press the
set the feature to the LED On option. To set the LED Off, while still holding
the Valet button, press *. (See Feature Table)
5. Release the Valet button to exit programming, or repeat the above to pro-
AUX
gram more features.
AUX
or AUX on the 3-button remote to set the feature to the LED Off
* Press
option.
Exit Programming
The siren emits one quick chirp, and then another lengthier chirp when exiting.
Programming is exited when one of the following occurs:
• Turn ignition ON
• Close the doors
• Press Valet button too many times
• There is no activity for 15 seconds
Feature menu
VALET Button LED ON OPTION
Pressess
*1 chirp
(Chirps/Flashes)
1 Active Arming
2 Confirmation Chirps ON
3 Ign-controlled Locking
ON
4 Active Locking
5 0.8 Second Doorlock
Pulse
6 Double Pulse Unlock OFF
7 Code Hopping ON
*Default settings
© 2012 Directed. All rights reserved.
3100 Auto Security System
Feature Decriptions
1. Active/Passive Arming
• Active Arming: the transmitter must be used to arm the system.
• Passive Arming: after exiting the vehicle the system will automati-
cally arm.
NOTE: Doors need to be closed and the system will passively arm
30 seconds after closing the doors.
2. Confirmation Chirps:
• ON: arm, disarm, and sensor warn-away chirps are active
• OFF: arm and disarm chirps are defeated, warn-away chirps are
active
3. Ign-controlled Locking
button on the remote to • ON: the door lock/unlock outputs will activate when ignition is
turned on/off
• OFF: the door lock/unlock outputs will not activate when ignition is
AUX
turned on/off
AUX
NOTE: Doors need to be closed for ignition lock to work.
4. Active/Passive Locking
• Active Locking: The doors will not lock when passively arming only
when using the remote.
• Passive Locking: The doors will automatically lock when the system
passively arms.
5. Door Lock Pulse
• 0.8 seconds: the door lock output pulses will be 800mS in duration
• 3.5 seconds: the door lock pulses will be 3.5 seconds in duration
6. Double Pulse Unlock
• OFF: the door unlock output will provide a single pulse.
• ON: the door unlock output will provide a double pulse.
7. Code Hopping
LED OFF OPTION
• ON: The code hopping portion of messages from the remote con-
2 chirps
trols will be decrypted before a command is activated
• OFF: The code hopping portion of the remote control messages will
Passive Arming
be ignored resulting in possible improvement in range.
Confirmation Chirps OFF
Horn Honk, 3-pin connector
Ign-controlled Locking OFF
OPEN
H/1
Passive Locking
H/2 BROWN/BLACK
3.5 Second Door Lock Pulse
H/3 OPEN
Double Pulse Unlock ON
This wire outputs a single pulse when arming the system and two pulses when dis-
arming.This wire also output pulses for 30 seconds when the system is triggered
Code Hopping OFF
or if panic mode is activated. If the vehicle has a (+) horn circuit, a standard
automotive SPDT relay or a relay assembly package(p/n 8617) must be used.
Remote Programming
Remote controls included in this system are pre-programmed in the standard but-
ton configuration, and are ready to use. This system will accept up to four remote
controls.
To add, delete, or reprogram remote controls with customized button configura-
tions, use the following procedure.
Important: Test the systems Ignition input, Door trigger input, Valet button, Status
LED, and siren for proper operation before proceeding.
1.
2.
3.
4.
5.
Exit Programming
The siren emits one quick chirp, and then another lengthier chirp when exiting.
Programming is exited if any of the following occurs:
•
•
•
•
Valet button presses
(Chirps/Flashes)
NO FUNCTION
(-) 200 mA HORN HONK OUTPUT
*The Auto-learn function cannot be used to program 3-button remotes. The chan-
NO FUNCTION
nels must be prorgammed indiviudally.
** Press any button of a programmed remote to delete all remote controls from
the system and to reset the features to default settings.
Select a System Function and the required number of valet button presses,
as described in the following table.
Open a door and turn the key ON (run position).
Press and release the Valet button to select the function. After pressing
and releasing corresponding to the function, then press the Valet button
once more and hold it. The LED flashes and the siren sounds to confirm
the selection.
While holding the Valet button, press the remote button that controls the
selected function. The siren emits one long sound to confirm programming.
Release the Valet button to exit programming, or to program another func-
tion return to step 3 and continue through step 5 again (Example: after
programming 'Arm only', select 'Panic only' by pressing and releasing the
Valet button two times, then press and hold it). Repeat to program more
functions.
Turn ignition off
Close the doors
Press Valet button too many times
There is no activity for 15 seconds.
System Function
1 Arm/Disarm/Panic
2 Aux Channel 2
3 Aux Channel 3
4 Arm only
5 Disarm only
6 Panic only
7 Auto-learn for 4-button configuration*
8 Delete remote controls & Reset features**
ADN3100 BL 2012 02
1