Page 1: Table Of Contents
All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.
Page 2: Introduction
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. ICONS Indicates a safety alert.
Page 3: Breaking-In Your Vehicle
INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Using your vehicle as a snowplow Do not use this vehicle for snowplowing.
Page 4: Vehicle Symbol Glossary
Introduction These are some of the symbols you may see on your vehicle. Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Brake System Brake Fluid - Non-Petroleum Based Master Lighting Switch Fog Lamps-Front Fuel Pump Reset Windshield Defrost/Demist Power Windows Front/Rear...
Page 5 Child Safety Door Lock/Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment Air Filter Vehicle Symbol Glossary Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature Battery Battery Acid...
Page 6: Instrumentation
Instrumentation Instrument panel dimmer switch (pg. 20) Headlamp control (pg. 19) PEDALS Power adjustable foot pedals (pg. 79) Rear window Parking brake release defroster control (pg. 21) Instrument cluster (pg. 8) DOOR AJAR km/h P RN FUEL DOOR Hood release (pg.
Page 7 Gearshift (includes overdrive button) (pg. 142) PUSH ON TAPE SEEK MUTE A4WD 4WD control * (pg. 145) Auxiliary power point (pg. 24) Electronic sound system (pg. 25) BASS TREB FADE TUNE SCAN AUTO SIDE 1 . 2 COMP SHUFF PANEL COOL WARM Climate control system...
Page 8: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES FUEL SERVICE ENGINE SOON FUEL DOOR Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information). When refueling, after the light comes on, the amount of fuel that is added will be less than the advertised capacity since there is fuel still in the tank.
Page 9 What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2.
Page 10 Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the ignition is turned to the ON position.
Page 11 High beams Illuminates when the high beam headlamps are turned on. SecuriLock anti-theft system This light indicates the anti-theft alarm system is armed. Momentarily illuminates when the ignition is turned to ON/START. If the light fails to illuminate, continues to flash or remains on, have the system serviced.
Page 12 Instrumentation Four wheel drive low (if equipped) Momentarily illuminates when the ignition is turned to the START RANGE position. Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive indicator (if equipped) Momentarily illuminates when the ignition is turned to the ON position.
Page 13 Instrumentation This light comes on when either the COAST/SET or RES/ACCEL controls are pressed. It turns off when the cruise cancel control is pressed, the brake is applied or the ignition is turned to the OFF position. Optional electronic instrument CRUISE cluster The “CRUISE”...
Page 14: Fuel Gauge
Instrumentation GAUGES FUEL SERVICE ENGINE SOON FUEL DOOR Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 15 Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Page 16 Instrumentation Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer RPMX1000 pointer continuously at the top of the scale may damage the engine. Battery voltage gauge This shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’s...
Page 17: Trip Computer
TRIP COMPUTER The trip computer tells you about the condition of your vehicle through a constant monitor of vehicle systems. You may select display features on the trip computer for a display of status. The appearance of your vehicle’s trip computer may differ depending on your vehicle’s option package, but the functions are the same.
Page 18 Instrumentation The fuel range function will flash for 5 seconds when you have approximately the following distance you can drive before the fuel tank is empty: 80 km (50 miles) 40 km (25 miles) 16 km (10 miles) Average fuel economy. The display will indicate the vehicle’s average fuel economy in liters/100 km (or miles/gallon) since last reset.
Page 19: Headlamp Control
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate.
Page 20: Panel Dimmer Control
Controls and features Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
Page 21: Power Adjustable Foot Pedals
To turn autolamps off, rotate the control clockwise to OFF. Foglamps are not controlled by the autolamps. In order to turn on the foglamps, you must turn the lamp switch to the pull toward you for fog. POWER ADJUSTABLE FOOT PEDALS Press and hold the rocker control to adjust accelerator and brake pedal.
Page 22: Reverse Sensing System (If Equipped)
Controls and features 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information. REVERSE SENSING SYSTEM (IF EQUIPPED) The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the reverse gear is selected. To help avoid personal injury, please read and understand the limitations on the reverse sensing system described below.
Page 23 Controls and features The reverse sensing system detects obstacles within approximately 1.8 meters (5.9 ft.) of the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
Page 24 Controls and features AUXILIARY POWER POINT The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. A second auxiliary power point is located on the left rear side of the console (behind the driver seat).
Page 25: Using Your Audio System
USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette (CD Changer Compatible) PUSH ON TAPE MUTE Premium AM/FM Stereo/Cassette (CD Changer Compatible) PUSH ON TAPE MUTE Controls and features TUNE SEEK SIDE 1 . 2 TUNE SEEK SIDE 1 . 2 BASS TREB FADE SCAN...
Page 26 Controls and features Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Page 27 to increase volume compensation to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Page 28 Controls and features Press to select the next disc in the CD changer. Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD mode (if equipped). Seek function in radio mode Press to find the next listenable station down the...
Page 29 Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again.
Page 30 Controls and features If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the control again.
Page 31 Tape/CD select To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. To begin CD play (if equipped with CD changer), ensure that the CDs are loaded.
Page 32 Controls and features Eject function Press the control to stop and eject a tape. Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction.
Page 33 identification or program type from RDS-equipped FM radio stations. The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired.
Page 34 Controls and features Info Jazz Oldies R & B Religious Rock Soft Top 40 Show With RDS activated, press the RDS control until SHOW is displayed. Use the SEL control to select TYPE (the display shows the program type), NAME (the display shows the call letters of the station) or NONE.
Page 35 Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected: JAZZ CLUB—jazz club with clearly reflected sounds. HALL—rectangular concert hall capacity of about 2 000 CHURCH—church with a high vault.
Page 36 Controls and features Premium AM/FM Stereo/Single CD Radio PUSH ON SCAN MUTE Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 37 The recommended level for speed sensitive volume is from level 1 through level 3. Level 0 turns the speed sensitive volume off and level 7 is the maximum setting. With the radio on, press and hold the volume control for five seconds, then press: to increase volume compensation...
Page 38 Controls and features Tune adjust for CD changer Press to select the previous disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc.
Page 39 Controls and features Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.). To stop on a particular selection, press the control again.
Page 40 Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Page 41 Rewind The rewind control works in CD mode. In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in CD mode.
Page 42 Controls and features Shuffle feature (if equipped) The shuffle feature operates in CD changer mode and plays all tracks on the current disc in random order. The shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again.
Page 43 Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: Classic Country Info Jazz Oldies R & B Religious Rock Soft Top 40 Show With RDS activated, press the...
Page 44 Controls and features Setting the clock Press the RDS control until SELECT HOUR or SELECT MINS is displayed. Use the SEL control to manually set the time. Press to increase hours/minutes. Press to decrease hours/minutes. Rear seat controls (if equipped) The rear seat controls allow the middle seat passengers to operate the radio, tape, CD or CD changer...
Page 45 Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to Turning speakers on and off.
Page 46 Controls and features Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped). Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2.
Page 47 Controls and features CD changer (if equipped) Your CD changer is located in the center console. Slide the door to access the CD changer magazine. Press to eject the magazine. 1. Pull the lever to remove a CD tray from the magazine.
Page 48 Controls and features 2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine.
Page 49 Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty.
Page 50 Controls and features Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation. Cassette and cassette player care Use only cassettes that are 90 minutes long or less. Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold.
Page 51: Climate Control System
Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.
Page 52 Controls and features The air conditioning compressor will operate in all modes except PANEL and FLOOR. However, the air conditioning will only function if the outside temperature is about 10°C (50°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle.
Page 53 sent to the windshield defroster ducts. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. -Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.
Page 54 Controls and features If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle.
Page 55 Controls and features Turning the EATC off Press OFF. The Outside Temperature function will continue to operate until the ignition is turned off. AUTOMATIC FLR • DEF Automatic operation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature.
Page 56 Controls and features To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. OUTSIDE TEMP MAX A/C VENT PNL • FLR For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window.
Page 57 The display will show manual fan operation. To return to automatic fan operation, press AUTOMATIC. Manual override controls The override controls are located at the bottom of the EATC and allow you to determine where airflow is directed. To return to full automatic control, press AUTOMATIC.
Page 58 Controls and features FLOOR-Allows for maximum heating by distributing outside air through the floor ducts. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate this mode. FLR DEF-Distributes outside air through the windshield defroster ducts and the floor ducts.
Page 59 The outside temperature reading is most accurate when the vehicle is moving. Higher readings may be obtained when the vehicle is not moving. The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station locations. Operating tips In humid weather, select DEF fogging on your windshield.
Page 60 Controls and features Auxiliary A/C-heater controls (if equipped) The auxiliary A/C-heater feature provides increased capacity to quickly heat or cool the vehicle. Besides the driver’s control panel for the front seat occupants, the second row auxiliary A/C-heater controls allow the rear passengers to control the temperature in the rear of the vehicle through a second control panel above the second row, or in the floor console.
Page 61 Controls and features or located in the overhead console. In order for the auxiliary A/C-heater controls to function, the driver’s REAR auxiliary A/C-heater control must be set to REAR. COOL WARM PANEL FLOOR The instrument panel climate PANEL controls must be on in order for the auxiliary A/C-heater to operate.
Page 62: Positions Of The Ignition
Controls and features Turn the temperature control to the desired temperature. You can get warm or cool air through either the overhead registers or floor vent by turning the auxiliary mode selector: Far left for airflow to the overhead registers. Far right for airflow to the rear floor vent.
Page 63: Turn Signal Control
TURN SIGNAL CONTROL Push down to activate the left turn signal. Push up to activate the right turn signal. SPEED CONTROL To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).
Page 64 Controls and features To turn speed control off Press OFF or Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
Page 65 To set a higher set speed Press and hold SET/SET ACC/ SET ACCEL. Release the control when the desired vehicle speed is reached or Press and release SET/SET ACC/ SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or Accelerate with your accelerator pedal.
Page 66 Controls and features To disengage speed control Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Page 67: Tilt Steering
Controls and features TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter.
Page 68 Controls and features Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds). Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position.
Page 69: Overhead Console
Controls and features Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of OVERDRIVE the gearshift lever. The Transmission Control Indicator Light (TCIL) (the word OFF) will illuminate on the end of the gearshift lever. The transmission will operate in all gears except overdrive.
Page 70 Controls and features Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: Place Velcro hook onto back side of aftermarket transmitter opposite of actuator control. Place transmitter into storage compartment, control down. Place the provided height adaptors onto the back of the storage bin door as needed.
Page 71 Without trip computer Press and release the rear portion of the moon roof control to open. Press and hold (as desired) the front portion of the moon roof control to close. To halt motion at any point during one-touch opening, press the control a second time.
Page 72 Controls and features Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error.
Page 73 Without trip computer 1. Press and hold the SELECT control until VAR appears in the display, then release. The display should show the current zone number. 2. Press the SELECT control until the desired zone number appears. The display will flash and then return to normal operation.
Page 74 Controls and features Without trip computer 1. Press and hold the SELECT control until CAL appears in the display (approximately eight seconds) and release. 2. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles.
Page 75 Press the portion of the VENT control to open the power rear quarter windows. Press the portion of the VENT control to close the power rear quarter windows. Interior Lamps Map lamps With trip computer Without trip computer To turn on the map lamps, press the control next to each lamp. Controls and features ROOF VENT...
Page 76: Illuminated Visor Mirror (If Equipped)
Controls and features Rear dome lamp The dome lamp lights when: any door is opened. the instrument panel dimmer switch is held up until the courtesy lamps come on. any of the remote entry controls are pressed and the ignition is OFF.
Page 77: Power Windows
POWER WINDOWS Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. One touch down Press AUTO completely down and release quickly.
Page 78: Power Door Locks
Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls WINDOW LOCK except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until...
Page 79: Power Side View Mirrors
POWER SIDE VIEW MIRRORS The ignition can be in any position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror.
Page 80: Center Console
Controls and features Signal mirrors (if equipped) When the turn signal is activated, the outer portion of the appropriate mirror housing will blink red. This provides an additional warning to other drivers that your vehicle is about to turn. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.
Page 81: Positive Retention Floor Mat (If Equipped)
Rear center console features (if equipped) The rear center console incorporates the following features: utility compartment cupholders POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
Page 82 If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the encoded ignition key is an approved Ford encoded ignition key.
Page 83 Spare coded keys can be purchased from your dealership and programmed to your anti-theft system. Refer to Programming spare SecuriLock keys for more information. If one or both of your coded keys are lost or stolen and you want to ensure the lost or stolen key will not operate your vehicle, bring your vehicle and all available coded keys to your dealership for reinitialization.
Page 84: Remote Entry System
Controls and features 2. Turn ignition to OFF and remove the first coded key from the ignition. 3. Within five seconds of turning the ignition to OFF, insert the second previously programmed coded key into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second but no more than five seconds).
Page 85 Controls and features Unlocking the doors Press this control to unlock the driver door. The interior lamps and running board lamps (if equipped) will illuminate. The memory mirrors/seat (if equipped) will also be moved to position 1, 2 or 3 depending upon which remote entry transmitter (1, 2 or 3) is used.
Page 86 Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Page 87 Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: Take all your vehicle’s transmitters to your dealer for programming, or Perform the programming...
Page 88 Controls and features Illuminated entry The illuminated entry system will turn on the interior lights when the remote transmitter unlock control is pressed. The illuminated entry system will turn off the interior lights if the ignition switch is turned to the ON position, or if the remote transmitter lock control is pressed, or after 25 seconds of illumination.
Page 89 1. Turn the ignition key to ON. 2. Press the power door unlock control three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock control three times. 5. Turn the ignition back to ON. The horn will chirp. 6.
Page 90 Controls and features 5. Turn the ignition back to ON. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated.
Page 91 Controls and features 2. Press 1/2 control within five seconds of step one. 7 8 9 0 3. Press 7/8 control and 9/0 control at the same time within five seconds of step 2. The system will now only respond to the factory set code.
Page 92: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 93 Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Lift handle to move seat forward or backward.
Page 94 Seating and safety restraints 60/40 split bench seat (if equipped) Lift the release bar to move the seat forward or backward. Ensure the seat is relatched into place. Pull the seatback handle up to recline the seat. Using the armrest (if equipped) Push the release control to move the armrest up or down.
Page 95 Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. The control is located on the outboard side of the seat cushion. Press front to raise or lower the front portion of the seat cushion.
Page 96 Seating and safety restraints Memory seats (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to three programmable positions. The memory seat control is located on the driver door. To program position one, move the driver seat to the desired position using the seat controls.
Page 97: Rear Seats
Seating and safety restraints REAR SEATS Head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 98 Seating and safety restraints 3. Press the green control on the seatback to release the closeout panel. Rotate the panel to closeout the space in the floor. 4. Once the second row seats are in the down position, the front seats may be readjusted.
Page 99 Reclining the seatback Locate the lever at the bottom of the seatback that reads “FOLD FLAT OR RECLINE”. Pull the lever upwards to recline the seatback. Third row seat The third row seat is equipped with combination lap and shoulder belts in the outboard seating positions and a manual adjust tongue lap belt in the center seating position.
Page 100 Seating and safety restraints Ensure that the second row seat is in the upright position in order to achieve optimum access to the third row. To minimize the risk of personal injury, the third row seat should not be left in the forward, stowed position while the vehicle is in motion. Please ensure that the seat is in the upright, fully latched position before putting the vehicle in motion.
Page 101 2. Before removing the seat, be sure that the detachable anchor tongue is stowed flat into the vehicle floor. 3. Use the black plastic clip (located just above the detachable anchor) to stow the loose seat belt. Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat...
Page 102 Seating and safety restraints Installing the third row seat Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. When reinstalling a rear seat in your vehicle it must be placed in its original position.
Page 103 Seating and safety restraints 3rd row tip/stow feature The 3rd row seat has a tip/stow feature to increase cargo space without removing the seat from the vehicle. To put seat in tip/stow position: 1. Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion.
Page 104 Seating and safety restraints 6. Pull down support bar and push into floor latch. To return seat to seating position: 1. Hold seat and pull support bar from floor latch. 2. Rotate support bar up under seat. 3. Rotate floor latch down into floor tub. 4.
Page 105 It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 106 Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free...
Page 107 How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 108 Seating and safety restraints Lap belts Adjusting the lap belt The lap belts should fit snugly and as low as possible around the hips, not around the waist. 1st row and 3rd row (if equipped) center seating positions The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming...
Page 109 Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, front passenger and second row passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button down and slide the height adjuster down.
Page 110 Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
Page 111 I’m not going far 3 of 4 fatal crashes occur within 25 miles of home. Belts are Ford designs its safety belts to enhance comfort. If uncomfortable you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible;...
Page 112 Seating and safety restraints One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Page 113 (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
Page 114: Air Bag Supplemental Restraint System (Srs)
This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles.
Page 115 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Seating and safety restraints...
Page 116 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Page 117 The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag.
Page 118: Side Air Bag System (If Equipped)
Seating and safety restraints The RCM (restraints control module) monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors, the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors). Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Page 119 Do not attempt to service, repair, or modify the air bag Supplemental Restraint System, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided.
Page 120 Seating and safety restraints by the collision will be inflated, even if the respective seat is not occupied. The air bag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The air bag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Page 121: Safety Restraints For Children
A difficulty with the system is indicated by one or more of the following: The readiness light (same light as for front air bag system) will either flash or stay lit. The readiness light will not illuminate immediately after ignition is turned on.
Page 122 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
Page 123: Safety Seats For Children
SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 124 Seating and safety restraints Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
Page 125 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 126 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 127 Seating and safety restraints Installing child safety seat in the second row center seating position with an automatic locking retractor 1. Place the child safety seat in the center seating position. 2. In a continuous motion, pull out enough webbing from the retractor to route the tongue through the child seat.
Page 128 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln/Mercury dealer. All second row and third row passenger side seating positions (if equipped) have a fabric strap installed near the bottom of the rear face of the seatback.
Page 129: Preparing To Start Your Vehicle
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 130 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns...
Page 131: Starting The Engine
FUEL SERVICE ENGINE SOON FUEL DOOR Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts.
Page 132 Starting recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle. Using the heater for longer than three hours will not harm the engine, so the heater can be plugged in the night before starting the vehicle.
Page 133 Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Page 134: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 135 ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
Page 136 Driving Parking brake Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released.
Page 137 Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Page 138: Air Suspension System (If Equipped)
Driving Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased. If the amount of effort required to steer your vehicle changes at a constant vehicle speed, have the power steering system checked by your dealer or a qualified service technician.
Page 139: Traction-Lok Axle (If Equipped)
The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver.
Page 140: Preparing To Drive Your Vehicle
Driving To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 141: Automatic Transmission Operation
AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1.
Page 142 Driving Driving with a 4–speed automatic transmission Understanding gearshift positions To put your vehicle in gear, start the engine, depress the brake pedal, then move gearshift lever out of P (Park). Hold the brake pedal down while you move the gearshift lever from P (Park) to another position.
Page 143 (Overdrive) can be deactivated by pressing the transmission control switch (TCS) on the end of the gearshift lever. The transmission control indicator light (TCIL) (the word OFF) on the end of the gearshift lever will illuminate. Drive – Not shown on the display. Activate by pressing the transmission control switch (TCS) on the end of the gearshift lever with the gearshift in the position.
Page 144: Four-Wheel Drive (4Wd) Operation (If Equipped)
Driving higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed. Forced Downshifts To gain acceleration in passing another vehicle, push the accelerator to the floor. The transmission will downshift to the appropriate gear: third, second or first gear.
Page 145 CONTROL-TRAC AUTOMATIC FOUR-WHEEL DRIVE SYSTEM (IF EQUIPPED) Your 4x4 features the heavy-duty Control-Trac system which includes a computer-operated transfer case. This unique system is interactive with the road, continually monitoring and adjusting torque delivery to the front and rear wheels to optimize vehicle control. Positions of the Control-Trac system The Control-Trac A4WD system functions in three modes:...
Page 146 Driving Using the Control-Trac system Shifting from A4WD to 4H Move the 4WD control from A4WD to 4H at any forward speed up to 88 km/h (55 mph). At temperatures below 0°C (32°F), shifts from A4WD to 4H should not be performed above 72 km/h (45 mph).
Page 147 Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside.
Page 148 Driving When driving through water, determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly. If the ignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes.
Page 149: Driving Through Water
Automatic transmission may shift frequently while driving up steep grades. Eliminate frequent shifting by shifting out of D (Drive). Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Avoid sudden applications of power and quick changes of direction on snow and ice.
Page 150 Driving Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. GVW (Gross Vehicle Weight): Base curb weight plus payload weight. The GVW is not a limit or a specification. GVWR (Gross Vehicle Weight Rating): Maximum total weight of the base vehicle, passengers, optional equipment and cargo.
Page 151 limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations. The Certification Label, found on the inside pillar of the driver’s door, lists several important vehicle weight rating limitations. Before adding any additional equipment, refer to these limitations. If you are adding weight to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the front axle reserve capacity (FARC).
Page 152 Driving 2. Weigh your vehicle as you customarily operate the vehicle without cargo. To obtain correct weights, try taking your vehicle to a shipping company or an inspection station for trucks. 3. Subtract your loaded vehicle weight from the maximum GCWR on the following charts.
Page 153 and turn lamps, back up lamps, battery charge, electric brakes (when a customer provided controller is installed) and ground. The kit included with your vehicle provides you with adaptors to attach the brake controller and convert the hitch connector for Class I trailer usage. Trailer towing table (with heavy duty trailer tow option) GCWR (Gross Combined Weight Rating)/trailer weights Rear...
Page 154 Driving Do not exceed the maximum loads listed on the Safety Compliance Certification label. For load specification terms found on the label, refer to Vehicle loading in this chapter. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of control...
Page 155 4. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0–13 mm (0.5 in) of the reference point. After proper adjustment, the rear bumper should be no higher than in Step 3. 5.
Page 156 If a distance of 80 km (50 miles) or a speed of 56 km (35 mph) must be exceeded, the drive shaft will have to be removed until the vehicle is being towed. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation.
Page 157 Improper removal/installation of the driveshaft can cause transmission fluid loss, damage to the driveshaft and internal transmission components. 4WD vehicles electronic shift transfer case (with automatic transmissions) 4x4 vehicles with electronic shift on the fly cannot be towed with any wheels on the ground.
Page 158: Luggage Rack (If Equipped)
Driving Disconnect the wiring to the trailer before backing the trailer into the water. Reconnect the wiring to the trailer after the trailer is removed from the water. LUGGAGE RACK (IF EQUIPPED) The rear crossbar can be adjusted to fit the item being carried. The front crossbar does not move.
Page 159: Getting Roadside Assistance
GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: 24–hours, seven days a week for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.) of three years or 60,000 km (36,000 miles),...
Page 160 Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB (1–877–894–2582).
Page 161: Fuses And Relays
Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Page 162 Roadside emergencies Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse Mini Rating Fuses Grey...
Page 163 The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 7.5A Roadside emergencies Passenger Compartment Fuse Panel Description Audio Overhead Trip Computer, Electronic Automatic Temperature Control (EATC), Powertrain Control Module (PCM), Cluster Cigar Lighter, OBD-II Scan Tool Connector Remote Entry Module, Mirrors, Memory Functions (Seats and Pedals) Speed Control Module, Reverse Lamp, EVO Module, Climate Mode Switch (Front...
Page 164 Roadside emergencies Fuse/Relay Fuse Amp Location Rating — — — Passenger Compartment Fuse Panel Description Cluster, Overhead Trip Computer, Compass, Brake Shift Interlock Solenoid, Air Suspension Module, GEM Module, EVO Steering Sensor, Heated Mirror, Rear Defroster, Reverse Sensing System Aux A/C Blower Relay (via fuse 22) Radio, Remote Entry Module, GEM Module Not Used Not Used...
Page 165 Fuse/Relay Fuse Amp Location Rating — — Relay 1 — Relay 2 — Relay 3 — Relay 4 — Relay 5 — Roadside emergencies Passenger Compartment Fuse Panel Description Starter Relay, Fuse 20, Transmission Range Switch Air Bag Module, Climate Mode Switch (Blower Relay), EATC, EATC Blower Relay, Feeds Fuse 7 Aux A/C, Heated Seats, Trailer Tow Battery...
Page 166 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 167 The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 20A * 30A* 30A* 20A* 20A* 15A* 20A* 30A* 15A* 20A* 20A* 10A* 15A* — 10A* — 10A* 15A* 10A* 10A* — — 15A* — 30A** 50A** 50A** Roadside emergencies Power Distribution Box Description Power Point...
Page 168 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 30A** 40A** — — 30A** 50A** 30A** 40A** 30A** 40A** 30A** — 40A** — — — — — — — — — — — — — — — Power Distribution Box Description 4x4 Shift Motor & Clutch Climate Control Front Blower Not Used Not Used...
Page 169: Changing The Tires
Fuse/Relay Fuse Amp Location Rating — — — — — *Mini fuses **Maxi fuses Relays Relays are located in the power distribution box and should be replaced by qualified technicians. CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed.
Page 170 Roadside emergencies Removing the jack handle 1. Open the hood. 2. Unsnap the end of the handle that is retained by the clip on the top of the windshield washer bottle. 3. Unsnap the shaft of the handle from the two retaining clips attached to the top of the radiator shroud.
Page 171 Stowing the spare tire 1. Lay the tire on the ground with the outboard side facing up. 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. Turn the spare handle clockwise until the tire is raised to its original position underneath the vehicle.
Page 172 Roadside emergencies 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) and turn engine OFF. 3. Block the diagonally opposite wheel. 4. Obtain the spare tire and jack from their storage locations.
Page 173 7. Turn OFF the air suspension switch (if equipped). 8. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the...
Page 174 Roadside emergencies Front (4x4) Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
Page 175: Jump Starting Your Vehicle
12. Remove the jack and fully tighten the lug nuts in the order shown. 13. Put flat tire, jack and lug wrench away. Make sure the jack is fastened so it does not rattle when you drive. 14. Unblock the wheels. 15.
Page 176 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 177 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 178 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
Page 179 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 180: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Page 181: Maintenance And Care
SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 182: Opening The Hood
Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2.
Page 183: Identifying Components In The Engine Compartment
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 and 5.4L V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7.
Page 184 Maintenance and care 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again.
Page 185 Motor oil displaying the API certification trademark will meet all requirements for your vehicle’s engine. Ford oil specification is WSS-M2C153-G. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty.
Page 186 Maintenance and care Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Page 187: Engine Coolant
In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 188 Maintenance and care Canada, Motorcraft CXC-10), or an equivalent premium engine coolant that meets Ford specification ESE-M97B44-A. A 50/50 mixture of distilled water and Ford Premium Engine Coolant provides: maximum cooling system efficiency. freeze protection down to -36° C (-34° F).
Page 189 Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or a premium engine coolant that meets Ford specification ESE-M97B44-A. DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color).
Page 190 Maintenance and care Do not put engine coolant in the windshield washer fluid reservoir. If engine coolant is sprayed onto the windshield, it could make it difficult to see through the windshield. When the engine is cool, add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir, until the coolant is at the “cold fill level”...
Page 191 Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44-A. Use of a recycled engine coolant which does not meet the Ford specification may harm engine and cooling system components.
Page 192 Maintenance and care decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.
Page 193: Checking And Adding Power Steering Fluid
Check the power steering fluid. Refer to the Scheduled Maintenance Guide for the service interval schedules. If adding fluid is necessary, use only Ford Premium Power Steering Fluid. 1. Start the engine and let it run until it reaches normal operating...
Page 194: Transmission Fluid
Maintenance and care 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and...
Page 195 Maintenance and care 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7.
Page 196: Driveline Universal Joint And Slip Yoke
Maintenance and care The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
Page 197 intervals. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will also be necessary. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.
Page 198 Maintenance and care When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 199: Air Filter Maintenance
7. Drive the vehicle to complete the relearning process. The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Page 200 Maintenance and care Changing the air filter element 1. Loosen the clamp that secures the air inlet tube to the engine air filter cover and disconnect the tube from the cover. 2. Loosen the clamp that secures the air filter cover to the air filter housing and carefully separate the cover from housing.
Page 201: Windshield Wiper Blades
Maintenance and care WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild...
Page 202: Information About Uniform Tire Quality Grading
10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 203 The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 204 If you do not follow these precautions, your vehicle may not drive properly and safely. Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford.
Page 205: Snow Tires And Chains
Follow these guidelines when using snow tires and chains: Use only cable type chains offered by Ford as an accessory or equivalent. SAE class “S” or other conventional link type chains may contact and cause damage to the vehicle’s wheel house and/or body.
Page 206: What You Should Know About Automotive Fuels
Maintenance and care WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 207 Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention.
Page 208 Maintenance and care Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use fuel containing methanol. It can damage critical fuel system components. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containing MMT.
Page 209 If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. Maintenance and care...
Page 210: Essentials Of Good Fuel Economy
Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in...
Page 211 The amount of empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Page 212 Maintenance and care Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits Smooth, moderate operation can yield up to 10% savings in fuel. Steady speeds without stopping will usually give the best fuel economy.
Page 213: Emission Control System
Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide. Conditions Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried).
Page 214 Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 215 Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter.
Page 216 Maintenance and care Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. At the back of the headlamp, pull clips rearward and up to release the headlamp assembly. 4. Slide headlamp assembly forward and off of guide ribs to expose the back of the bulb and wiring connector.
Page 217 Maintenance and care 11. Straighten alignment pins, making them parallel with the outer edges of the attachment standoff. 12. Carefully insert the headlamp assembly into the vehicle making sure the alignment pins are inserted into the proper holes and into the guide ribs.
Page 218 Maintenance and care 3. Carefully pry the lamp assembly away from the vehicle to expose the bulb sockets. 4. Rotate the bulb socket counterclockwise and remove from lamp assembly. 5. Pull bulb straight out of socket and push in the new bulb. 6.
Page 219 Maintenance and care 2. Carefully pull the lamp assembly away from the vehicle to access the bulbs. 3. Remove the bulb socket by turning counterclockwise and a careful pull. 4. Pull the bulb straight out of the sicket and push in the new bulb. 5.
Page 220: Replacing The Interior Bulbs
Maintenance and care Function Headlamps Front park/turn lamps Front sidemarker Foglamps Dome/map lamps Turn/tail/brake lamps Liftgate lamp Backup lamp License lamp High-mount brake lamp Running board lamp (if equipped) All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: interior overhead lamp...
Page 221: Aiming The Headlamps
If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
Page 222 Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products.
Page 223 Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.
Page 224 Ford Ultra-Clear Spray Glass Cleaner, (E4AZ-19C507–AA), available from your Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water.
Page 225 Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label. Regular cleaning of your leather upholstery helps maintain its resiliency and color.
Page 226: Capacities And Specifications
Fuel filter Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Name Brake fluid High Performance DOT 3 Motor Vehicle Brake Fluid Engine oil...
Page 227 Fluid Ford Part Name Transmission Motorcraft fluid MERCON V Motorcraft MERCON ATF Transfer case Motorcraft fluid MERCON ATF Engine coolant Premium Engine Coolant Capacities and specifications Application 4R70W 4R100 (4x2) 4R100 (4x4) 4x4 vehicles 4.6L V8 engine with 1 row radiator 4.6L V8 engine...
Page 228 Capacities and specifications Fluid Ford Part Name Front axle Motorcraft SAE lubricant 75W-90 Premium 4x4 Front Axle Lubricant Rear axle Motorcraft SAE lubricant 75W-140 Synthetic Rear Axle Lubricant Windshield Ultra-Clear washer fluid Windshield Washer Concentrate Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.
Page 229: Lubricant Specifications
Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.
Page 230 Capacities and specifications Ford part Item name Driveshaft, slip Premium Long spline, double Life Grease Cardan joint center ball Engine coolant Ford Premium Engine Coolant Engine oil Motorcraft SAE 5W-30 Super Premium Motor 4x4 front wheel High bearings, 4x4 Temperature...
Page 231 Use of any fluid other than the recommended fluid may cause transmission damage. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118-A for complete refill of Ford Traction-Lok rear axles. Capacities and specifications...
Page 232: Engine Data
Capacities and specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Vehicle dimensions 4x2 mm (in) (1) Overall length (2) Vehicle width *width including mirrors *with optional running boards (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear...
Page 233 Capacities and specifications...
Page 234: Certification Label
Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block and transmission. MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX...
Page 235: Customer Assistance
5,000 participating Ford or Lincoln/Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options.
Page 236 Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you.
Page 237 Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Assistance Center: Your telephone number (home and business)
Page 238 Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Page 239 Ford Motor Company Customer assistance...
Page 240 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 241: Getting Assistance Outside The U.s. And Canada
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 242 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 243 Customer assistance Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (Canada only) Ford Extra Strength Upholstery Cleaner (not available in Canada)
Page 244 Customer assistance Comfort and convenience Cabin air filter Cargo nets Cargo organizers Cargo trays Dash trim (wood grain) Engine block heaters Tire step Travel equipment Auto headlamps with DRL Bumper mount bike carrier Daytime running lights (DRL) Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery...
Page 245 Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and sport) Hood deflectors Inside mirror with compass display Inside mirror with compass and temperature display Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Outside signal mirror (requires power mirrors) Rear air deflectors Side window air deflectors...
Page 246: Ordering Additional Owner's Literature
(Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. ORDERING ADDITIONAL OWNER’S LITERATURE...
Page 247: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
Page 248: Index
Index Accessory delay ...78 Air bag supplemental restraint system ...114,118 and child safety seats ...116 description ...114,118 disposal ...118,121 driver air bag ...116,119 indicator light ...9,118,120 operation ...116,119 passenger air bag ...116,119 side air bag ...118 Air cleaner filter ...199,200,226 Air conditioning ...51 automatic temperature control system ...54...
Page 249 ...187 refill capacities ...191,226 specifications ...229,232 Cruise control (see Speed control) ...63 Customer Assistance ...159 Ford accessories for your vehicle ...242 Ford Extended Service Plan ...235 Getting assistance outside the U.S. and Canada ...241 Getting roadside assistance ...159 Getting the service you need ...235...
Page 250 Index Floor mats ...81 Fluid capacities ...226 Foglamps ...20 Four-Wheel Drive vehicles ..12,144 control trac ...22,145 description ...145 driving off road ...147 electronic shift ...22,146 indicator light ...12 preparing to drive your vehicle ...140 Fuel ...206 calculating fuel economy ...210 cap ...209 capacity ...226 choosing the right fuel ...208...
Page 251 lighting up panel and interior ...20 location of components ...8 Jump-starting your vehicle ...175 Keyless entry system autolock ...89 locking and unlocking doors ...91 programming entry code ...90 Keys key in ignition chime ...13 positions of the ignition ...62 Lamps autolamp system ...20 bulb replacement specifications chart ...219...
Page 252 Index fluid, specifications ...229,232 Preparing to drive your vehicle ...140 Radio ...25 Relays ...161,169 Remote entry system ...84,85 illuminated entry ...88 locking/unlocking doors ...85 panic alarm ...85 replacement/additional transmitters ...87 replacing the batteries ...86 Reverse sensing system ...22 Roof rack ...158 Safety belts (see Safety restraints) ...13,104 105,106,107,109...
Page 253 Water, Driving through ...149 Windows power ...77 rear wiper/washer ...68 Windshield washer fluid and wipers checking and adding fluid ...187 checking and cleaning ...201 liftgate reservoir ...187 operation ...67 replacing wiper blades ...201 Wrecker towing ...180 Index...
Page 255: Filling Station Information
(4x2) Automatic transmission fluid capacity-4R100 (4x4) Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.
Page 256 Filling station information Some transmission fluids may be labeled as dual usage, such as MERCON and MERCON V. These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON type fluid. However, these dual usage fluids may be used in transmissions that require the MERCON V type fluid.

This manual is also suitable for:

Expedition 2002

Ford 2000 Expedition Owner's Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Ford 2000 Expedition

Summary of Contents for Ford 2000 Expedition

This manual is also suitable for:

Table of Contents