Page 7: Table Of Contents
Instrument Panel ....1-2 Initial Drive Information ..1-4 Remote Keyless Entry (RKE) System ..... . 1-4 Remote Start .
Page 9 B. Turn and Lane Change Lever. Driver Information Center (DIC) Display. See (If Equipped). G. Charging Status Indicator. H. Light Sensor. See K. Driver Information Center (DIC) Controls. See M. Data Link Connector (DLC) (Out of View). See (If Equipped). R.
Page 10: System
This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual. The Remote Keyless Entry (RKE) transmitter will work up to 60 m (195 ft) away from the vehicle.
Page 11: Remote Start
This feature starts the heating or air conditioning systems and rear window defogger from outside the vehicle. Normal operation of the system will return after the vehicle has been turned on. The engine may start to support the climate control operation. 1.
Page 12: Windows
To open the hatch, with all doors unlocked, press the button on the underside of the hatch and lift up. Always close the hatch before driving. Do not press the button while closing the hatch; it will unlock it again. The power window switches are on the driver door armrest.
Page 13 Move the lever up or down to raise or lower the seat. See Seat Height Adjuster under To recline the seatback: 1. Lift the lever. 2. Move the seatback to the desired position, and then release the lever to lock the seatback in place.
Page 14: Heated Seats
If available, the controls are on the center stack. To operate, the vehicle must be on. Press to heat the driver or passenger seat cushion and seatback. Press the button once for the highest setting. With each press of the button, the heated seat will change to the next lower setting, and then the off setting.
Page 15: Safety Belts
Press the touch screen AUTO or AUTO button. The button color will change to green when this feature is on. When the vehicle is on, this feature will automatically activate the heated seats at the level required by the vehicle's interior temperature. The active high, medium, low, or off heated seat level will be indicated by the manual heated seat button...
Page 16: Passenger Airbag
The passenger sensing system will turn off the right front passenger frontal airbag and passenger knee airbag under certain conditions. The driver airbags, seat mounted side impact airbags, and roof rail airbags are not affected by the passenger sensing system. See for more information.
Page 17: Interior Lighting
To adjust the steering wheel: 1. Pull the lever (A) down. 2. Move the steering wheel up or down. 3. Pull or push the steering wheel closer or away from you. 4. Pull the lever (A) up to lock the steering wheel in place.
Page 18: Instrument Panel
Turns on the parking lamps, together with the sidemarker lamps, taillamps, license plate lamps, and instrument panel lights. Turns on the headlamps, together with the parking lamps, sidemarker lamps, taillamps, license plate lamps, and instrument panel lights. For more information, see: The windshield wiper lever is on the side of the steering column.
Page 19: Climate Controls
Heating, cooling, and ventilation can be controlled by using the climate control buttons and the climate touch screen. A. Temperature Control B. Driver and Passenger Heated Seats C. Defrost D. Climate E. Auto (Automatic Operation) Rear Window Defogger G. Manual Fan Control...
Page 20 A. Driver and Passenger Auto Heated Seats B. Air Delivery Mode Controls C. Auto Recirculation D. Manual Recirculation E. Outside Air Temperature Display Climate Modes: Fan Only, ECO, Comfort G. Climate Power Gauge H. Manual Fan Control Temperature Setting Display Air Conditioning Indicator K.
Page 21: Satellite Radio
This vehicle's radio is part of the navigation system. See Vehicles with an XM Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. XM is a satellite radio service based in the 48 contiguous United States and 10 Canadian provinces.
Page 22: Steering Wheel Controls
The Bluetooth system allows users with a Bluetooth-enabled cell phone to make and receive hands-free calls using the vehicle audio system, microphone, and controls. The Bluetooth-enabled cell phone must be paired with the in-vehicle Bluetooth system before it can be used in the vehicle.
Page 23: Cruise Control
The cruise control buttons are on the steering wheel. Press to turn the cruise control system on and off. An indicator light will turn on or off in the instrument cluster. Press to disengage cruise control without erasing the set speed from memory.
Page 24: Information
Exposure to high voltage can cause shock, burns, and even death. The high voltage components in the vehicle can only be serviced by technicians with special training. High voltage components are identified by labels. Do not remove, open, take apart, or modify these components.
Page 25 1. The charge port door release button is on the driver door inner trim panel. With the vehicle in P (Park), press the button for one second and release to open the charge port door. The charge port door can also be opened using the RKE transmitter.
Page 26 4. Then plug in the vehicle plug of the charge cord into the charge port on the vehicle. Verify that the charging status indicator illuminates on top of the instrument panel and a horn chirp occurs. See for more information. 5.
Page 27: Fueling
6. Place the charge cord, face down, into the storage compartment with the front edge (F) of the charge cord body under the clips (G) located in the front of the storage compartment. The vehicle plug (B) should be on the right side of the charge cord.
Page 28: Total Vehicle Range
3. Turn the fuel cap counterclockwise to remove. While refueling, hang the fuel cap tether from the hook on the inside of the fuel door. Complete refueling within 30 minutes of pushing the fuel door button found on the driver side door. If refueling more than 30 minutes, push the fuel door button again.
Page 29: Service
Never try to do your own service on high voltage components. You can be injured and the vehicle can be damaged if you try to do your own service work. Service and repair of these high voltage components should only be performed by a trained service technician with the proper knowledge and tools.
Page 30: Compressor Kit
During cooler conditions, the low tire pressure warning light may appear when the vehicle is first started and then turn off. This may be an early indicator that the tire pressures are getting low and the tires need to be inflated to the proper pressure.
Page 31: Efficiency
Use the following tips to help maximize energy efficiency and range. The ball indicator should be kept green and in the center of the gauge. Inefficient acceleration is indicated when the ball turns yellow and travels above the center of the gauge.
Page 32 Using the heat and air conditioning systems decreases the energy available for electric driving. Optimal energy efficiency is achieved with the heat, air conditioning, and fan turned off. Less energy is used at low fan speeds. When using the fan: Fan Only is the most energy efficient climate setting as long is not selected.
Page 33: Program
U.S.: TTY Users: Canada: As the owner of a new Chevrolet, you are automatically enrolled in the Roadside Assistance program. This program provides security and convenience in the event of an on-road failure or emergency situation. Service is provided 24 hours a day, 365 days a year for the 5 year/160 000 km (100,000 mi) coverage period.
Page 34 Push this blue button to connect to a specially trained OnStar Advisor to verify your account information and to answer questions. Push this red emergency button to get priority help from specially trained OnStar Emergency Advisors. Push this button for hands free, voice activated calling and to give voice commands for Hands Free Calling and Turn by Turn...
Page 35 information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310. This vehicle may have talk and mute buttons that can be used to interact with OnStar Hands-Free Calling. See for more information. On some vehicles, the mute button can be used to dial numbers into voice mail systems, or to dial phone extensions.
Page 121: Adjustment
Instrument Panel Overview ..5-4 Steering Wheel Adjustment . . . 5-6 Steering Wheel Controls ..5-6 Horn ......5-7 Windshield Wiper/Washer .
Page 122 Vehicle Messages ... 5-45 Battery and Charging Messages ....5-45 Brake System Messages ..5-46 Cruise Control Messages .
Page 125 B. Turn and Lane Change Lever. Driver Information Center (DIC) Display. See (If Equipped). G. Charging Status Indicator. H. Light Sensor. See K. Driver Information Center (DIC) Controls. See M. Data Link Connector (DLC) (Out of View). See (If Equipped). R.
Page 126 To adjust the steering wheel: 1. Pull the lever (A) down. 2. Move the steering wheel up or down. 3. Pull or push the steering wheel closer or away from you. 4. Pull the lever (A) up to lock the steering wheel in place.
Page 127 Press SRC to change between radio and CD or DVD. Press + to increase the volume; press decrease the volume. Press near the horn symbols to sound the horn. The Pedestrian Friendly Alert provides momentary soft note horn sound. See more information.
Page 128 Clear ice and snow from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged wiper blades should be replaced. See Heavy snow or ice can overload the wipers. If the wiper motor overheats, the windshield wipers will stop until the motor cools and the wiper control is turned off.
Page 129 Remove the cover to access and replace when not in use. Certain accessory plugs may not be compatible with the accessory power outlet and could overload vehicle or adapter fuses. If a problem is experienced, see your dealer. When adding electrical equipment, be sure to follow the installation instructions included with the equipment.
Page 130 The following screens may appear, depending on the status. This screen indicates that the charge cord is not connected. Plug the charge cord in to charge the vehicle. This screen indicates that the charge cord is connected and the charging is complete. This screen indicates that charging is active and the estimated charge completion time is 10:00 a.m.
Page 131 This screen indicates that charging is programmed to be delayed with an estimated completion time of 7:00 a.m. This screen indicates that the vehicle is fully charged and the charge cord is not connected. This screen indicates that the charge cord is connected, but the vehicle cannot be charged.
Page 133 Second Row Passenger Safety Belt Reminder Light. See S. Electric Drive Unit Positions. AD. Driver Safety Belt Reminder Light. See...
Page 134 There are two instrument cluster display configurations to choose from. Press CONFIG located left of the steering wheel to change the configuration. See for more information. Choose either the Simple or Enhanced Configuration display. The Enhanced Configuration displays the Driver Efficiency Gauge.
Page 135 The speedometer shows the vehicle speed in both kilometers per hour (km/h) and miles per hour (mph). The DIC menu can be used to change the units. The odometer shows how far the vehicle has been driven, in either kilometers or miles. The trip odometer is within the Driver Information Center.
Page 136 The vehicle has a compass display in the instrument cluster above the speedometer. The compass receives its heading and other information from the Global Positioning System (GPS) antenna and vehicle speed information. The compass system has automatic calibration and zone adjustment features.
Page 137 This gauge is a guide to driving in an efficient manner by keeping the ball green and in the center of the gauge. The leaves stop spinning when the vehicle stops or when the ball travels away from the center of the gauge.
Page 138 When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. The light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled during driving while the vehicle is moving.
Page 139 Second row seating positions monitored for safety belt use are represented by a colored symbol indicating safety belt status. When the vehicle is started, two safety belt symbols come on and stay on for several seconds in the instrument cluster to alert the driver that passengers may need to fasten their safety belts.
Page 140 A message may also display in the Driver Information Center (DIC). for more information. If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash.
Page 141 If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system.
Page 142 If the malfunction indicator lamp comes on and stays on, while the vehicle is in ON/RUN, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent.
Page 143 An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emission system malfunction: Check that the fuel cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 144 The vehicle will not pass this inspection if the OBD II (On-Board Diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if the 12 volt battery has recently been replaced or if the 12 volt battery has run...
Page 145 This status light comes on when the parking brake is applied. If the light flashes and stays on after the parking brake is released, or while driving, there is a problem with the Electric Parking Brake system. If the light does not come on, or remains flashing, see your dealer.
Page 146 This light should come on briefly when the vehicle is in ON/RUN. If it does not come on, have the vehicle serviced by your dealer. If the ABS warning light stays on longer than a few seconds after the vehicle is in ON/RUN, or comes on and stays on while driving, try resetting the system.
Page 147 This light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by your dealer. If the system is working normally the indicator light then goes off. If the light comes on and stays on while driving, there could be a problem with the TCS/StabiliTrak system and the vehicle might need service.
Page 148 This indicates that there may be a problem with the Tire Pressure Monitor System. The light flashes for about one minute and stays on steady until the vehicle is in OFF. This sequence repeats each time the vehicle is in ON/RUN. See for more information.
Page 149 This light comes on briefly when the vehicle is started. If the light remains on while driving, there is a problem with the security system. See your dealer for service. For more information, see The high-beam on light comes on when the high-beam headlamps are in use.
Page 150 If a door, hood, or hatch is not completely closed, a light comes on together with a graphic in the Driver Information Center (DIC). The DIC indicates when a door, the hood, or the hatch is open. The light displays the open area as shaded. The DIC and the light both display when the vehicle is moving.
Page 151 The center stack screen displays Charging, Power Flow, and Energy Information. See the information that follows. The Climate Control, Infotainment, and Vehicle Personalization also display information in this screen. For more information on these systems, see: The center stack controls only need a light touch to operate and work best with bare hands.
Page 152 Battery Power Vehicle is stationary in electric mode and no power is flowing to the wheels. Engine Power Engine is active with energy flowing to the wheels. Engine Power Vehicle is stationary in extended range mode and no power is flowing to the wheels. Engine and Battery Power Both the engine and battery are active with energy flowing to the wheels.
Page 153 Power Off No power is flowing to the wheels. This vehicle has three programmable charge modes. To view the current charge mode status in the center stack display, press the button on the center stack and then press the Charging button at the top of the touch screen.
Page 154 vehicle estimates the charging start time considering the programmed departure time for the current day of the week. Charging begins at the start time and is complete by the departure time only if sufficient time is allowed after the charge cord is plugged in.
Page 155 From the Charge Mode Status screen, press Change Charge Mode. Select one option: Immediately upon plug in. Delayed based on departure time. Delayed based on electric rates & departure time. From the Delayed Charge Mode Status screen, press Edit to change the departure time for each day of the week to match your personal schedule.
Page 156 From the Departure Time & Rate Information screen, press Select Charge Rate Preference. Press one of the following options to select the Charge Rate Preference. Charge during Peak, Mid Peak, and Off Peak Rates: The vehicle will charge during any rate period and will select when to charge to minimize the total cost of the charge.
Page 157 To edit the Summer/Winter Schedule: 1. Press Summer/Winter Schedule. 2. Press Edit. To edit the Yearly Schedule: 1. Press Yearly Schedule. 2. Press Edit. From the Select Electric Rate Plan screen, press Summer/Winter Schedule then press Edit. 1. Press Summer Start. 2.
Page 158 1. Press Weekday or Weekend. 2. Press Edit next to the row to be changed. Weekdays are Monday through Friday and use the same rate schedule. Weekends are Saturday and Sunday and use the same rate schedule. Both weekday and weekend schedules must be set.
Page 159 1. Press + or to adjust the time. 2. Press Peak, Mid-Peak, or Off-Peak to select the electric rate. 3. Press the Back button to store changes. Only the finish time can be edited. The start time is automatically populated in the rate table. From the Select Electric Rate Plan screen, press View (Summer, Winter, or Yearly) Schedule.
Page 160 To temporarily override a Delayed Charge Mode from inside the vehicle: 1. Press the charge port door release button on the driver door to view the Charge Mode Status pop-up in the center stack display. 2. Press Charge Immediately Upon Plug In.
Page 161 The Programmable Charging system will be disabled if the Charge Complete Time cannot be confidently estimated. If the Programmable Charging system is consistently disabled, see your dealer for details. To view the Energy Usage, Energy Efficiency, and Efficiency Tips, press button on the center stack and then press the Energy Info button at the top of the touch...
Page 162 The Energy Usage information will also appear automatically on power off when Retained Accessory Power is active. This automatic pop-up can be disabled through the vehicle personalization. See Energy Summary Exit Pop-up under The Energy Efficiency screen is accessed by pressing Energy Efficiency on the Energy Usage screen.
Page 163 The Driver Information Center (DIC) display is in the instrument cluster. The DIC displays information about the vehicle. It also displays warning messages if a system problem is detected. See for more information. View the DIC displays by pressing the DIC buttons located to the left of the steering wheel.
Page 164 The trip displays show fuel used, average fuel economy, and distance traveled since the last trip reset. Reset the trip data by pressing and holding the SELECT button when either Trip A or Trip B is displayed. This displays the percentage of remaining oil life.
Page 165 Messages displayed in the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. Messages that do not require immediate action can be acknowledged and cleared by pressing the SELECT knob.
Page 166 This message displays when there is a problem with the high voltage charging system. See your dealer for service. This message displays when the brake fluid level is low. See This message displays if the electric parking brake is on while the vehicle is in motion.
Page 167 This message displays when in Mountain Mode and the mode becomes unavailable. See Mountain Mode under This message displays when in Sport Mode and the mode becomes unavailable. See Sport Mode under This message displays when the vehicle should be shifted to P (Park).
Page 168 This message displays when the engine oil needs to be changed. After changing the engine oil, the Engine Oil Life System must be reset. See for information on how to reset the system. See more information. This message displays if low oil pressure levels occur.
Page 169 This message displays when the RKE transmitter is not detected while attempting to start the vehicle. The transmitter battery may be weak. See Starting the Vehicle with a Low Transmitter Battery under more information. This message displays if the RKE transmitter is no longer detected in the vehicle.
Page 170 This message displays when the propulsion power is reduced and can affect the ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration...
Page 171: System (Tcs)
This message displays when there is a problem detected with the Traction Control System (TCS). The vehicle is safe to drive, but the TCS is not operational. See for information on resetting the system. This message displays if there is a problem with the airbag system.
Page 172 This message displays if there is a problem with the power steering system. Take the vehicle to your dealer for service. This message displays if there is a problem with the vehicle. Take the vehicle to your dealer for service. Depending on the severity of a crash, this message may come on along with the airbag readiness...
Page 173 This message displays when the vehicle speed is limited. This message displays when the washer fluid level is low. For information on filling the washer fluid, see The Vehicle Personalization features can be accessed by using either the infotainment controls or the touch screen in the center stack display.
Page 174 1. Turn the TUNE/MENU knob to highlight the function. 2. Press the TUNE/MENU knob to turn the function on or off. A checkmark next to the function indicates that the function is on. Use the touch screen icons and menus on the center stack display to select personalization features.
Page 175 Select the Climate and Air Quality menu to display: Auto Fan Speed Auto Heated Seats Remote Start Auto Heat Seats Auto Defog This feature sets the automatic fan speed to maintain the desired interior tempurature. This selection is available on vehicles with the Automatic Climate Control system.
Page 176 To turn the auto defog on or off: 1. Press the Vehicle menu. 2. Select Climate and Air Quality. 3. Turn the auto defog feature on or off. 4. Press Back to return to the previous menu. Select the Comfort and Convenience menu and the following will be displayed: Chime Volume...
Page 177 This allows the selection of a language: 1. Press the Vehicle menu. 2. Select Languages. 3. Select English, French, or Spanish. 4. Press Back to return to the previous menu. Select the Lighting menu and the following will be displayed: Exit Lighting Vehicle Locator Lights This allows the selection of how...
Page 178 This allows selection of which doors will automatically unlock when the vehicle is shifted into P (Park). The available options are: All Doors Driver Door To select how the doors will automatically unlock: 1. Press the Vehicle menu. 2. Select Power Door Locks. 3.
Page 179 This allows selection of what feedback is provided when unlocking the vehicle with the RKE transmitter. The available options are: Lights and Horn Lights Only Horn Only To select the remote lock feedback: 1. Press the Vehicle menu. 2. Select Remote Locking, Unlocking, Starting.
Page 180 When on, the horn will chirp rapidly three times if an RKE transmitter is left in the vehicle. To turn the remote left in vehicle reminder feature on or off: 1. Press the Vehicle menu. 2. Select Remote Locking, Unlocking, Starting. 3.
Page 181 Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Remote system programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Remote system buttons be erased for security purposes. See Erasing Universal Remote System Buttons later in this section.
Page 182 3. Press and hold for five seconds the newly trained Universal Remote system button (the button selected in Step 2) while observing the indicator light and garage door activation. If the indicator light stays on continuously or the garage door starts to move when the Universal Remote system button is pressed and released, then the...
Page 183 If you have questions or need help programming the Universal Remote system, call 1 800 355 3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming.
Page 184 To reprogram any of the three Universal Remote system buttons: 1. Press and hold the desired Universal Remote system button. Do not release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 of the section Programming the Universal Remote System.
Page 191 Infotainment System Introduction Infotainment ....7-2 Theft-Deterrent Feature ..7-3 Overview ..... . 7-3 Radio AM-FM Radio .
Page 192: Infotainment System
Infotainment System Introduction Infotainment The vehicle has a navigation system with an AM-FM radio. Read the following pages to become familiar with its features. WARNING Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others.
Page 193: Theft-Deterrent Feature
Theft-Deterrent Feature The theft-deterrent feature works by learning a portion of the Vehicle Identification Number (VIN) to the infotainment system. The infotainment system does not operate if it is stolen or moved to a different vehicle. Overview When the navigation system is turned on, a screen may appear that must be read and acknowledged.
Page 194 Infotainment System A. RADIO BAND (AM, FM, XM) B. HDD/DVD/AUX (Source) C. FAV (Favorite) D. TUNE/MENU BACK TONE G. CONFIG (Configuration) SEEK/SEEK (Phone/Mute) TP (Time Program) K. DEL (Delete) REC (Record) (Play/Pause) N. VOL/ (Volume/Power) O. INFO (Information) DEST (Destination) Q.
Page 195 S. AS1-2 (Autostore) (Eject) NAV (Navigation) Menu Use the Navigation Menu screen to access the navigation system settings. See for more information. Press the NAV button to view the navigation map screen. The map and the current vehicle location display. Press the NAV button to change between a map/audio split view or a full map view.
Page 196 Infotainment System Languages To change the display language, for more information. The vehicle supports English, French Canadian, and Spanish. The default language is English. English and Metric Unit Conversion To change the display readings between English and metric units, for more information. Deleting Personal Information The navigation system can record and store destinations and personal...
Page 197 Entering an Address and Point of Interest, and Storing Preset Destinations The vehicle must be in P (Park) to perform these operations. Entering an Address To more easily find a city or a street name: Enter the street name first instead of the city name, or vice versa.
Page 198 Infotainment System Entering a Point of Interest (POI) To set a destination by entering a Point of Interest (POI): 1. Press VOL/ to turn the system on. 2. A caution could appear. Press OK to proceed. 3. Press the DEST button. 4.
Page 199 Using the Stored Preset Destinations These destinations are available for selection while driving. 1. Press VOL/ to turn the system on. 2. A caution could appear. Press the OK screen button to proceed. 3. Press the DEST button. 4. Press one of the available preset destination screen buttons.
Page 200: Radio
7-10 Infotainment System Radio AM-FM Radio Playing the Radio Audio Source Menu VOL/ (Volume/Power): 1. Press to turn the radio on or off. 2. Turn to increase or decrease the volume. The volume is adjusted for the current audio source, active navigation voice guidance, voice prompts, or audio cues.
Page 201 Navigation Audio System Sound Menu To access the Sound menu, press the TONE button. Use the Sound menu to adjust the following features: Setting the Tone Adjusting the Speakers Setting the Tone To adjust the tone using the Sound menu: Treble: Press + or to change the level.
Page 202 7-12 Infotainment System Radio Menu There are two ways to access the Radio menu: Press the CONFIG button, then press the Radio screen button. Turn the TUNE/MENU knob until Radio displays. Press the TUNE/MENU knob to select Radio or press the Radio screen button to display more options within that feature.
Page 203 Auto Volume Select OFF, Low, Medium, or High sensitivity to automatically adjust the volume to minimize the effects of unwanted background noise that can result from changing road surfaces, driving speeds, or open windows. This feature works best at lower volume settings where background noise is typically louder than the sound system volume.
Page 204 7-14 Infotainment System To scroll through the pages, press the FAV button. The current page number displays above the preset buttons. The stored stations for each list display on the preset buttons at the bottom of the screen. The number of preset FAV lists can be changed.
Page 205 To resume listening to the broadcast at the point left off, press again. Timeshift stops recording and erases the buffer when the vehicle is turned off or the station or source is changed. Before turning the vehicle off, press so that timeshift keeps recording for 20 minutes.
Page 206: Satellite Radio
7-16 Infotainment System Satellite Radio Satellite Radio Service Vehicles with an XM satellite radio tuner and an XM satellite radio subscription can receive XM programming. XM is a satellite radio service based in the 48 contiguous United States and 10 Canadian provinces. XM satellite radio has a wide variety of programming and commercial-free music, coast to coast, and in...
Page 207: Radio Reception
No Title Info: The system is working properly. No song title information is available at this time on this channel. No CAT Info: The system is working properly. No category information is available at this time on this channel. No Information: The system is working properly.
Page 208: Multi-Band Antenna
7-18 Infotainment System The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. Static can occur when things like storms and power lines interfere with radio reception. When this happens, try reducing the treble on the radio.
Page 209 The system is capable of playing: Most audio CDs CD-R CD-RW MP3 or unprotected WMA formats DVD-Video DVD-Audio DVD-R/RW DVD+R/RW When playing any compatible recordable disc, the sound quality can be reduced due to disc quality, the method of recording, the quality of the music or video that has been recorded, or the way the disc has been handled.
Page 210 7-20 Infotainment System There are two ways to play a CD/DVD: Insert the disc and play starts automatically. Press the HDD/DVD/AUX button, then press the disc screen button. Playing an Audio CD A track number displays at the beginning of each track. Song, Artist, and Album information displays when available.
Page 211 Playing an Audio and Video DVD To view the DVD video, the vehicle must be in P (Park) or the parking brake must be engaged. After the DVD is loaded, the menu options display on the DVD screen. The menu options time out and a full screen appears after about 10 seconds.
Page 212 7-22 Infotainment System SEEK: 1. Press to seek to the beginning of the current or previous chapter. If the chapter has played for less than five seconds, it goes to the previous chapter. If the chapter has played longer than five seconds, the current chapter is restarted.
Page 213: Mp3
Subtitle: Press while a DVD is playing to view with subtitles on or off or to change the language of the subtitles. Continue pressing to cycle through the available subtitle languages and to turn subtitles off, depending on the DVD playing. Pan Scan: Pan Scan is a method of adjusting widescreen film images so that they can be proportioned to...
Page 214 7-24 Infotainment System The Artist/Album/Song Titles/ Genre information requires a CD to be fully scanned before the music navigator works with these menus. Disc scanning does not occur when the disc is being played. When an MP3 is loaded in the player, MP3 displays.
Page 215 Press any of the following category buttons on the MP3 Music Menu to display the corresponding category screen: Folders/Playlists Press to view the folders stored on the disc. Select a folder to view the list of all songs in that folder.
Page 216: Hard Drive Device (Hdd)
7-26 Infotainment System Empty Directory or Folder If a root directory or folder is empty or contains only folders, the player advances to the next folder in the file structure that contains a compressed audio file. The empty folder(s) are not displayed or numbered.
Page 217 Recording from a CD to the Hard Drive The speed of the recording increases if you are listening to another source while recording. To record all tracks from the disc: 1. Load a CD or press the HDD/DVD/AUX button until the Disc screen displays.
Page 218 7-28 Infotainment System Duplicate Content When the record function starts, there is a check to verify that the content does not already exist on the hard drive. If the entire content of the CD exists on the hard drive, it will not record the content. If it is determined that some or none of the content exists, then only that missing content will be copied to the...
Page 219 TUNE/MENU: 1. Turn to the right or left to display All Songs. 2. Turn it again to cycle through the list. 3. Press the TUNE/MENU knob to select the song. The system plays the selected song and returns to the CD screen. DEL (Delete): 1.
Page 220 7-30 Infotainment System All Songs: 1. Press to view a list of all songs on the hard drive. 2. Select a song from the list. Once selected, All Songs Mode displays. Genres: 1. Press to view the genres on the hard drive.
Page 221 USB-Supported Devices The USB connector uses the following: USB 2.0. USB flash sticks or pen drives. Portable USB Hard Drives. Special care needs to be taken related to the power source of these devices (USB bus powered vs. external power). Portable media adapters that support SD Flash, Compact Flash, or SD Micro.
Page 222 7-32 Infotainment System SEEK: 1. Press to seek to the beginning of the current or previous track. If the track has been playing for less than five seconds, the previous track plays. If playing longer than five seconds, the current track restarts. 2.
Page 223 Eject USB: Press when the USB is to be removed. If the USB is disconnected without selecting Eject USB, the files could become corrupted. ® Playing from an iPod This feature supports the following iPod models: iPod (fifth generation or later) iPod nano (first, second, third, fourth, and fifth generation) iPod classic...
Page 224 7-34 Infotainment System Playlists: 1. Press to view the playlists stored on the iPod. 2. Select a playlist name to view a list of all songs in the playlist. 3. Select the desired song from the list. Once a song has been selected, Playlist Mode appears on the iPod main screen.
Page 225 Audio Books: 1. Press to view the audio books stored on the iPod. 2. Select the audio book from the list. Once an audio book has been selected, Audio Book Mode appears on the iPod main screen. Podcasts appear with the general music.
Page 226 7-36 Infotainment System Playing Audio Book Content After activating and transferring www.audible.com files to the system, play the files: 1. Press the HDD/DVD/AUX button until the HDD source is selected. 2. Press the HDD Menu. The HDD Music Menu displays. Scroll down to the Audio Book option and select.
Page 227 Selecting Another Audio Book To play a different audio book from the one selected, return to the Audio Book menu options. To change the audio book currently playing: 1. Press the TUNE/MENU knob or press the HDD Menu screen button. The HDD Music Menu displays.
Page 228: Auxiliary Devices
7-38 Infotainment System Changing Chapters within an Audio Book To change chapters within an audio book: While the audio book is playing, turn the TUNE/MENU knob. The chapter list of the current book displays. Select a chapter from the list. To return to the current chapter being played, select the chapter with the checkmark at the right.
Page 229: Navigation
Navigation Using the Navigation System Read this section thoroughly to become familiar with how the navigation system operates. Keeping your eyes on the road and your mind on driving is important for safe driving. The navigation system has built-in features intended to help do this.
Page 230 7-40 Infotainment System Always be alert and obey traffic and roadway laws and instructions, regardless of the guidance from the navigation system. Because the navigation system uses street map information that does not include all traffic restrictions or the latest road changes, it may suggest using a road that is now closed for construction or a turn that is prohibited by signs at the...
Page 231 SEEK: 1. Press to seek to the beginning of the current or previous track or chapter. If the track or chapter has been playing for less than five seconds, the previous track or chapter plays. If playing longer than five seconds, the current track or chapter restarts.
Page 232 7-42 Infotainment System Touch Screen Buttons Touch screen buttons are on the screen and are highlighted when a feature is available. Some screen buttons highlight when active and grey out when inactive. Alpha-Numeric Keyboard Letters of the alphabet, symbols, punctuation, and numbers, when available, display on the navigation screen as an alpha or numeric keyboard.
Page 233 Voice Prompt This menu allows changes to the voice features. The touch screen buttons available are: Voice Volume: Adjust the voice volume for guidance and voice recognition prompts by pressing or + screen buttons or by turning the VOL/ knob on the infotainment system.
Page 234: Maps
7-44 Infotainment System Back Track Press the Back Track screen button to turn on, off, or delete the recording and displaying of the traveled path. Display Back Tracks: When active, the traveled path displays. Record Back Track Points: When active, the traveled path is recorded. Delete Back Track Points: The recorded path is deleted.
Page 235 Installing the DVD Map Disc Your dealer installs the map database information on the HDD. An updated map disc can be used to update the map database information. See Before updating the map database on the HDD, read the following steps: 1.
Page 236: Map Adjustments
7-46 Infotainment System Map Adjustments The scale of view on the map can be adjusted. Map Scales There are two methods to change the map scale: Turn the TUNE/MENU knob clockwise or counterclockwise to zoom out or in. Press the Map Scale button on the left bottom corner of the map screen to change the zoom level.
Page 237: Navigation Symbols
Navigation Symbols Following are the most common symbols that appear on a map screen. The vehicle symbol indicates the current position and heading direction of the vehicle on the map. The destination symbol marks the final destination after a route has been planned.
Page 238 7-48 Infotainment System Press this screen symbol to change to 3 D mode. The 3-D symbol is the same as the Heading-up symbol, but the map is in 3-D. The No GPS symbol appears when there is no Global Positioning System (GPS) satellite signal.
Page 239 Urgent Maneuver An urgent maneuver is displayed when the next maneuver is less than or equal to 0.8 km (0.5 mi) away on a residential road or less than or equal to 1.5 km (2 mi) away on a highway. Driving on a Highway Driving on a Residential Road Non-Urgent Maneuver...
Page 240 7-50 Infotainment System When this symbol is selected, the distance and time remaining from the current vehicle position to the first waypoint displays. This menu displays if the symbol and waypoints are entered. Select the main map view to display the distance and time remaining from the current vehicle position to any of the set waypoints or final...
Page 241: Destination
2. Select the new POI icon. 3. The new icon is on the Show POI Icons menu. List: Displays all available POIs. Clear: Clears all selected POIs. Nearby: Displays up to 200 of the selected POIs within 32 km (20 mi) of the current vehicle position.
Page 242 7-52 Infotainment System Cross Street Name: Enter a street name that intersects with the selected street. A checkmark displays on the right side when the field has been selected and the destination can be entered. After an entry step is completed, the checkmark moves to the next item.
Page 243 3. Select the street name field. Enter the street name. Do not enter directional information or street type. Use the space screen button between street and city names. Use the backspace screen button to delete an incorrect character. A list displays if four or fewer names are available.
Page 244 7-54 Infotainment System A list displays if four or fewer names are available. If there are more than four, there is a match counter with a number of available POI names. Press the List screen button to view the list. 4.
Page 245 Previous Destination Select a destination from a list of previous destinations. Up to 15 points that have been previously entered can be recalled. If the list is full, the oldest destinations are automatically deleted once the newest destinations are added. 1.
Page 246 7-56 Infotainment System 3. Select the destination from the list. 4. Press Go on the confirmation screen if the information is correct. The route calculates. 5. Select the route preference for Fastest, Shortest, or Easiest. See Entering an Address and Point of Interest, and Storing Preset Destinations under more information.
Page 247 3. Enter the coordinates for the destination in degrees, minutes, and seconds. 4. Press Go on the confirmation screen if the information is correct. The route calculates. 5. Select the route preference for Fastest, Shortest, or Easiest. See Entering an Address and Point of Interest, and Storing Preset Destinations under more information.
Page 248 7-58 Infotainment System Voice Prompt Select Voice Volume to change the volume of voice prompts and voice recognition. Select the Voice Guidance, Speech Confirmation Feedback, or Traffic Voice Prompt screen buttons to turn voice prompts on or off for each category.
Page 249 3. Enter the waypoint by any of the add destination methods. See more information. The system calculates and highlights the route and the route can be started. 4. To add more waypoints, press the DEST button. Press the Add Waypoint screen button to add the waypoint in the order desired on the route.
Page 250 7-60 Infotainment System (Fast Reverse or Forward Scroll): Press the fast reverse scroll arrow to go to the start point. Press the fast forward scroll arrow to go to the final destination. These buttons display once the reverse/forward scroll button has been selected. (Reverse or Forward Scroll): Press the reverse scroll arrow to go to the start point.
Page 251 5. Press Change Icon. 6. Select an icon from the list. 7. Press the OK screen button to save the changes. To edit the name of an address book: 1. Press the DEST button. 2. Press the Address Book screen button. A list displays the address book entries.
Page 252 7-62 Infotainment System 3. Select the address book entry to be deleted. 4. Press the Delete Entry screen button. A confirmation message displays. To add a preset destination from the address book: 1. Press the DEST button. 2. Press the Address Book screen button.
Page 253 Menu Screen Button Various navigation system settings are available through the Menu screen button. Some options are only available after a route is planned. 1. Press the NAV button to view the Map screen. 2. Press the Menu screen button or the TUNE/MENU knob on the faceplate.
Page 254: Onstar ® Destination
7-64 Infotainment System ® OnStar Destination Download The OnStar Destination Download lets an OnStar subscriber ask an OnStar Advisor to download a destination to the navigation system. OnStar will send address information and location coordinates of the destination into the navigation system.
Page 255 Route Guidance Not Active If an OnStar destination is downloaded while route guidance is not active, the navigation system displays a pop-up screen and the following available screen functions: Press the Go screen button; the navigation system starts route calculation to the destination(s) received.
Page 256: Configure Menu
7-66 Infotainment System Previous Destinations Previously downloaded OnStar destinations are saved under Previous Destinations in the navigation system where they can be accessed or saved to the address book. Map Destination Screen Functions Destination Map Screen If the map screen is used to show destination, it has map screen capabilities such as Go, Save, Zoom, Scroll, etc.
Page 257 If activated, traffic information displays: Unscheduled traffic incident data, such as accidents and disabled vehicles. Scheduled traffic incident data, such as road construction and road closures. Traffic flow information (rate of speed data). Flow data might not be available in all markets. Traffic information is delivered to the vehicle by the XM Radio satellites.
Page 258 7-68 Infotainment System It could take some time to sort the received information. The list of traffic conditions displays in the order of distance from the vehicle, for up to approximately 125 km (75 mi). With a route planned, traffic events display on the route. Not all traffic conditions may display.
Page 259 Traffic: Press to enable or disable the traffic function. Show Traffic ICONs: Press to display traffic icons on the map screen. Also, select what traffic information displays. Traffic Flow Status Enables or disables the green, yellow, red, and black arrows that display beside the roads and shows the traffic flow or extent of a traffic event.
Page 260 7-70 Infotainment System On Route Press the On Route screen button to display all events ahead on the current active route. No traffic events reported on route displays if there are none to report. Name Press the Name screen button to display traffic events in alphabetical order.
Page 261 Traffic Event Information Use to display additional details of a traffic event. This screen can display when: Scrolling to an event on the map and then pressing Info. Selecting a traffic event listed on the Traffic Event List screen. Approaching a traffic event. Back, Map, More, and Avoid These buttons have common functions across all Detailed...
Page 262 7-72 Infotainment System Alternate Route When Alternate Route Available displays, a possible quicker route is available and can be selected to detour around the traffic condition. Press the Yes screen button and the new route is calculated. This option is only available when the multiple car icon appears.
Page 263 Weather (where available) Press INFO, then press it again until the Weather screen button is selected or press the Weather screen button. Current Condition Press INFO until the Weather screen button is selected to show the current weather condition in the city of the vehicle s current position.
Page 264: Global Positioning
7-74 Infotainment System Display Press the CONFIG button to enter the menu options. Turn the TUNE/MENU knob to scroll through the available setup features. Press the TUNE/MENU knob or press the Display screen button to display other options within that feature. Dimming Mode Auto (Automatic): The screen background automatically adjusts...
Page 265: Vehicle Positioning
When the vehicle is not receiving signals from the satellites, a symbol appears on the map screen. See This system might not be available or interferences can occur if any of the following is true: Signals are obstructed by tall buildings, trees, large trucks, or a tunnel.
Page 266: Problems With Route
7-76 Infotainment System Problems with Route Guidance Inappropriate route guidance can occur under one or more of the following conditions: The turn was not made on the road indicated. Route guidance might not be available when using automatic rerouting for the next right or left turn.
Page 267: Database Coverage
Database Coverage Explanations Coverage areas vary with respect to the level of map detail available for any given area. Some areas feature greater levels of detail than others. If this happens, it does not mean there is a problem with the system. As the map data is updated, more detail can become available for areas which previously had limited...
Page 268 7-78 Infotainment System Canceling Voice Recognition 1. Press and release the steering wheel button to cancel a command, or if the system response does not match the verbal command. 2. The system replies, Voice recognition canceled. Pressing any other radio or steering wheel control, other than the volume knob or the volume steering wheel button...
Page 269 This system is able to recognize commands in different languages, such as English, French Canadian, and Spanish. The system only recognizes commands based on the language selected. To increase or decrease the voice volume during a voice recognition session, turn the volume knob of the radio, or press the volume steering wheel buttons.
Page 270 7-80 Infotainment System Display Commands Display (set) day (mode), display (select) day (mode): This command instructs the system to switch the display to day mode. Display (set) night (mode), display (select) night (mode): This command instructs the system to switch the display to night mode. Display (set) auto (mode), display (select) auto (mode): This command instructs the system...
Page 271 General Navigation Commands Feedback on, feedback off: This command instructs the system to turn on and off the voice recognition feedback. When feedback is ON, the system responds to commands with a talk back phrase. When feedback is OFF, the system responds to commands with a chime.
Page 272 7-82 Infotainment System Destination and Guidance Commands Navigation (go to) preset destination (number) (one, two, three, four, five, or six): These commands instruct the system to set one of the preset destinations one through six as the new destination. Navigation delete: This command instructs the system to delete the destination, route, or next waypoint.
Page 273 The state name displays. In some cases the radio shows a candidate list with the closest matches to the spoken state name. The system asks the user to select an item from the candidate list either by pressing the desired choice, or by saying the list number of the desired choice.
Page 274 7-84 Infotainment System OnStar (if equipped) Command Hands Free: This command instructs the system to enter the OnStar voice recognition system. See Hands-Free Calling in the OnStar Owner's Guide for more information. Help Commands Help Radio (help) CD (help), DVD (help), Disc (help) Display (help) Navigation (help)
Page 275: Phone
Route (used in conjunction with another command) Next waypoint (used in conjunction with another command) Add to waypoint (used in conjunction with another command) Replace destination (used in conjunction with another command) Yes (used in conjunction with another command) No (used in conjunction with another command) Destination (used for Destination VR entry, available...
Page 276 7-86 Infotainment System Using Voice Recognition To use voice recognition, press the button on the steering wheel. The system responds with a tone. After the tone say Hands Free to use the Bluetooth voice recognition system. The system then responds with Ready, followed by a tone.
Page 277 Connecting to a Different Phone To connect to a different cell phone, the Bluetooth system looks for the next available cell phone in the order in which all available cell phones were paired. Depending on which cell phone you want to connect to, you may have to use this command several times.
Page 278 7-88 Infotainment System 3. One at a time, say each number to store. After each number is entered, the system repeats back the number it heard followed by a tone. After the last number has been entered, say Store, and then follow the directions given by the system to save a name tag for this number.
Page 279 Using the Digit Dial Command The digit dial command allows a phone number to be dialed by entering the number one at a time. After each number is entered, the system repeats back the number it heard followed by a tone. If an unwanted number is recognized by the system, say Clear at any time to clear the...
Page 280 7-90 Infotainment System Three Way Calling Three way calling must be supported on the cell phone and enabled by the wireless service carrier. 1. While on a call, press 2. Say Three way call. 3. Use the dial or call command to dial the number of the third party to be called.
Page 281 Voice Pass-Thru Voice pass thru allows access to the voice recognition commands on the cell phone. See your cell phone manufacturer's user guide to see if the cell phone supports this feature. To access contacts stored in the cell phone: 1.
Page 282 7-92 Infotainment System Pairing a Phone Using the Infotainment System The pairing process can be started by using the controls on the infotainment system. 1. Press the CONFIG button. Turn the TUNE/MENU knob until the Phone menu displays. Press the TUNE/MENU knob or press the Phone screen button to display other options.
Page 283 Listing All Paired and Connected Phones 1. Press the CONFIG button. Turn the TUNE/MENU knob until the Phone menu displays. Press the TUNE/MENU knob or press the Phone screen button to display other options. 2. Turn the TUNE/MENU knob until Bluetooth displays. Press the TUNE/MENU knob or press the Bluetooth screen button to display other options.
Page 284 7-94 Infotainment System Deleting a Paired Phone 1. Press the CONFIG button. Turn the TUNE/MENU knob until the Phone menu displays. Press the MENU knob or press the Phone screen button to display other options. 2. Turn the TUNE/MENU knob until Bluetooth displays.
Page 285 4. Turn the TUNE/MENU knob, then press it to select the phone to be deleted. Follow the on-screen prompts to delete the device from the system. 5. Once a phone has been deleted, the only way to connect back to that phone is to pair the phone again.
Page 286 7-96 Infotainment System 3. Turn the TUNE/MENU knob until Device List displays. Press the TUNE/MENU knob or press the Device List screen button to display other options. 4. Select the phone to be linked and then follow the on-screen prompts. 5.
Page 287 Making a Call Press on the infotainment system, to access the Phone Menu. Enter Number Use this option to enter a phone number and make a call. 1. Turn the TUNE/MENU knob, then press it to select Enter Number selection. A dial pad displays.
Page 288 7-98 Infotainment System The Phone Book feature also has a search menu that can be accessed by pressing that option screen button. Once the Search menu displays, turn the TUNE/MENU knob to scroll through the list, then press the TUNE/MENU button to select the desired list item.
Page 289 2. Turn the TUNE/MENU knob, then press this knob or press either Incoming Calls, Outgoing Calls, or Missed Calls. Once one of these options has been selected, a pop-up menu displays. A list of persons and places will display for the selected option. Turn the TUNE/MENU knob, then press this knob or press the appropriate screen button to...
Page 290 7-100 Infotainment System Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. Switching Calls (Only Available with Call Waiting) This feature allows switching between calls, making one call active, and placing the other on hold.
Page 291 Ending a Call To end a call: 1. Press 2. Select Hang Up. Mute or UnMute a Call 1. Press 2. Select Mute Call. 3. Select Mute Call again to unmute the call. Dual Tone Multi-Frequency (DTMF) Tones The in-vehicle Bluetooth system can send numbers during a call.
Page 292 7-102 Infotainment System NOTES...
Page 367 General Information ..10-3 California Proposition 65 Warning ....10-3 California Perchlorate Materials Requirements ..10-3 Accessories and Modifications .
Page 368 Tires ......10-48 Winter Tires ....10-49 Tire Sidewall Labeling .
Page 369 For service and parts needs, visit your dealer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 370 Adding non dealer accessories or making modifications to the vehicle can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control, and stability control.
Page 371 This vehicle can be lifted with a hoist or a service jack. Do not use any other type of jack to lift the vehicle. This vehicle can be lifted with a hoist at the four locations, as illustrated. The front lifting points can be accessed from either side of the vehicle, behind the front tires.
Page 372 Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. Raising the vehicle with the jack improperly positioned can damage the vehicle or the vehicle may fall and cause you or others...
Page 373 There are four points where the vehicle can be lifted with a service jack. When lifting the vehicle from the rear, place the service jack directly under the spring seat. When lifting the vehicle from the front, place the service jack directly under the cradle mount.
Page 374 Never try to do your own service on high voltage battery components. You can be injured and the vehicle can be damaged if you try to do your own service work. Service and repair of these high voltage battery components should only be performed by a trained service technician with the proper knowledge and tools.
Page 375 Keep a record with all parts receipts and list the mileage and the date of any service work performed. To open the hood: 1. Turn the vehicle off before opening the hood. If the vehicle is on, the engine will start when the hood is opened.
Page 377 A. Engine Coolant Surge Tank and Pressure Cap. See C. Engine Oil Dipstick. See D. High Voltage Battery Coolant Reservoir and Pressure Cap. E. Engine Cover. Engine Oil Fill Cap. See G. Power Electronics Coolant Reservoir and Pressure Cap. H. Brake Fluid Reservoir. See Brake Fluid under High Voltage Cables (Orange Color).
Page 378 To ensure proper engine performance and long life, careful attention must be paid to engine oil. Following these simple, but important steps will help protect your investment: Always use engine oil approved to the proper specification and of the proper viscosity grade. See Selecting the Right Engine Oil in this section.
Page 379 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through. Selecting the right engine oil depends on both the proper oil specification and viscosity grade: Use and ask for engine oils with the dexos...
Page 380 Use of Substitute Engine Oils if dexos is unavailable: In the event that dexos approved engine oil is not available at an oil change or for maintaining proper oil level, you may use substitute engine oil displaying the API Starburst symbol and of SAE 5W-30 viscosity grade.
Page 381 Do not add anything to the oil. The recommended oils with the dexos specification and displaying the dexos certification mark are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty.
Page 382 When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary. A CHANGE ENGINE OIL SOON message comes on. Change the oil as soon as possible within the next 1 000 km (600 mi). It is possible that, if driving under the best conditions, the oil life system might indicate that an oil...
Page 383 To inspect or replace the air filter: 1. Open the hood. See 2. Locate the engine air cleaner/ filter assembly on the passenger side of the engine compartment. A. Retaining Clips B. Air Duct Clamp C. Electrical Connector 3. Disconnect the air duct by loosening the air duct clamp (B).
Page 384 When it is safe to lift the hood: A. Engine Coolant Surge Tank and Pressure Cap B. Engine Cooling Fans (Out of View) The electric cooling fans under the hood can start up even when the engine is not running and can cause injury.
Page 385 During vehicle operation and also during charging, the high voltage battery cells in the vehicle are kept within a normal operating temperature range. If the temperature rises above this temperature, the battery cooling system turns on the air conditioning compressor and cools the coolant until the correct temperature is reached.
Page 386 The power electronics and charger modules are cooled using the same coolant loop. The power electronics and charger modules in the vehicle are kept below a maximum temperature. If the temperature rises above this temperature, the electric engine cooling fans will turn on and cool the coolant until the correct temperature is reached.
Page 387 The engine cooling system in the vehicle is filled with DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for 5 years or 240 000 km (150,000 mi), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low.
Page 388 The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant surge tank. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the cold fill mark, add a 50/50 mixture of clean, drinkable...
Page 389 If coolant is needed, add the proper DEX-COOL coolant mixture at the coolant surge tank. The coolant surge tank pressure cap can be removed when the cooling system, including the surge tank pressure cap and upper radiator hose, is no longer hot. 1.
Page 390 The vehicle is equipped with an electric power steering system. No fluid or general maintenance is required. When adding windshield washer fluid to the vehicle, be sure to read the manufacturer's instructions before use. If operating the vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing.
Page 391 This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
Page 392 The brake master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: The brake fluid level goes down because of normal brake lining wear.
Page 393 Check brake fluid by looking at the brake fluid reservoir. See With the vehicle not running for at least one minute, the maximum fluid level (A) is at the top of the reservoir body. With the vehicle running, the fluid level should be in the proper operating range (B) between the MIN and MAX marks.
Page 394 This vehicle has a high voltage battery and a standard 12 volt battery. If the vehicle is in a crash, the sensing system may shut down the high voltage system. When this occurs, the high voltage battery is disconnected and the vehicle will not start.
Page 395 Remove the 12 volt battery black, negative ( ) cable from the battery to keep the 12 volt battery from running down or use a battery trickle charger. In addition, to avoid potential damage to the high voltage battery, perform the following recommended steps: Store the high voltage battery with 1/2 charge or less.
Page 396 When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface. 2.
Page 397 Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the electric parking brake. To check the electric parking brake's holding ability: With the propulsion system active and the electric drive unit in N (Neutral), slowly remove foot pressure from the regular brake pedal.
Page 398 The headlamp aiming system has been preset at the factory. If the vehicle is damaged in an accident, the aim of the headlamps may be affected and adjustment may be necessary. It is recommended that a dealer adjust the headlamps. To re-aim the headlamps yourself, use the following procedure.
Page 399 4. At the wall, measure from the ground upward (A) to the recorded distance from Step 3 and mark it. 5. Draw or tape a horizontal line (B) on the wall the width of the vehicle at the height of the mark in Step 4.
Page 400 For the proper type of replacement bulbs, see For any bulb changing procedure not listed in this section, contact your dealer. Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.
Page 401 To replace the high/low beam headlamp: 1. Open the hood. See 2. Remove the air cleaner cover. 3. Remove the air cleaner assembly by pulling up to release the rear two retention posts from the securing grommets. Then pull it forward to remove the remaining retention post from the securing grommet.
Page 402 3. Turn the bulb socket counterclockwise to remove it from the bulb assembly. 4. Pull the bulb from the bulb socket. 5. Push a new bulb straight into the bulb socket. 6. Reinstall the bulb socket by lining up the tabs in the lamp assembly and turn it clockwise to lock it into place.
Page 403 6. Reinstall the lamp assembly (C) into the fascia by inserting the left side first. 7. Push the spring clip side into place. Back-Up Lamps 3157K High/Low Beam HIR2 (9012) Headlamps License Plate 168LL Lamps (W5W) For replacement bulbs not listed here, contact your dealer.
Page 404 If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed. Choose some feature of the vehicle that is not needed to use and replace it as soon as possible. An electrical overload may cause the lamps to go on and off, or in some cases to remain off.
Page 405 A fuse puller is located in the engine compartment fuse block. The vehicle may not be equipped with all of the fuses, relays, and features shown. Engine Control Module Switched Power Emissions Not Used Ignition Coils/Injectors Empty Empty Rear Defogger (Lower Grid) Empty Empty...
Page 406 Traction Power Inverter Module and Transmission Control Module Battery Engine Control Module Battery Left High Beam Headlamp Empty Empty Empty Rechargeable Energy Storage System (High Voltage Battery) Coolant Pump Sensing Diagnostic Module Run/Crank Run/Crank for Fuel System Control Module/Vehicle Integration Control Module Vehicle Integration Control...
Page 407 Traction Power Inverter Module Run/Crank Run/Crank for Air Conditioning Control Module/Instrument Cluster/Passenger Airbag Display/ Accessory Power Module Empty Empty Power Window Front Empty Antilock Brake System Electronic Control Unit Charge Port Door Empty Empty Empty Antilock Brake System Motor Cooling Fan Right Front Wipers Charger...
Page 408 The instrument panel fuse block is on the driver side end of the instrument panel. To access the fuses, open the fuse panel door by pulling out. To reinstall the door, insert the bottom tab first, then push the door back into its original location. A fuse puller is located in the engine compartment fuse block.
Page 409 Empty Empty Body Control Module 1/Body Control Module Electronics/Keyless Entry/Power Moding/ Center High Mount Stoplamp/License Lamps/Left Daytime Running Lamp/Left Front Parking Lamp/ Right Rear Taillamp/ Hatch Release Relay Control/ Washer Pump Relay Control/Switch Indicator Lights Body Control Module 4/Left Headlamp Empty Empty Empty...
Page 410 A fuse puller is located in the engine compartment fuse block. The vehicle may not be equipped with all of the fuses, relays, and features shown. Steering Wheel Switch Backlighting Empty Empty Body Control Module 3/Right Headlamp Body Control Module 2/Body Control Module Electronics/Hatch Lamp/Right Daytime...
Page 411 Body Control Module 7/Left Front Turn Signal/Right Rear Stop and Turn Signal Lamp/Child Security Lock Relay Control Body Control Module 8/Locks ® OnStar Universal Garage Door Opener (If Equipped) Blower Motor Empty Empty Empty Empty Empty Empty Empty Empty Empty Empty DIODE Empty...
Page 412 A fuse puller is located in the engine compartment fuse block. The vehicle may not have all of the fuses, relays, and features shown. Empty Fuel System Control Module Passive Start Module Heated Seats (If Equipped) Driver Door Switches (Outside Rearview Mirror/ Charge Port Door Release/Refuel...
Page 413 Regulated Voltage Control/Ultrasonic Front and Rear Parking Assist (If Equipped) Horn Rear Power Windows Electric Parking Brake Rear Defog (Upper Grid) Empty Hatch Release Empty Empty Rear Defog (Upper Grid) Hatch Release Empty Empty Empty Empty Empty Horn DIODE Empty...
Page 414 Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer. Poorly maintained and improperly used tires are dangerous.
Page 415 Consider installing winter tires on the vehicle if frequent driving on snow or ice covered roads is expected. All season tires provide good overall performance on most surfaces, but they may not offer the traction or the same level of performance as winter tires on snow or ice covered roads.
Page 416 Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S.
Page 417 The three digit number indicates the tire section width in millimeters from sidewall to sidewall. A two digit number that indicates the tire height to width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide.
Page 418 The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards.
Page 419 The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire.
Page 420 The number of designated seating positions multiplied by 68 kg (150 lbs) plus the rated cargo load. See Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. A label permanently attached to a vehicle showing the vehicle's capacity weight and the original equipment tire size...
Page 421 For additional information regarding how much weight the vehicle can carry, and an example of the Tire and Loading Information label, see How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.
Page 422 As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them...
Page 423 This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmit the tire pressure readings to a receiver located in the vehicle.
Page 424 This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure. A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold.
Page 425 The malfunction light and DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See "TPMS Sensor Matching Process" later in this section. The TPMS sensor matching process was started but not completed or not completed successfully after rotating the tires.
Page 426 There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. Follow the TPMS sensor matching process: 1. Set the parking brake. 2.
Page 427 GM recommends that the tires, including the spare, be inspected for signs of wear or damage at least once a month. Replace the tire if: The indicators at three or more places around the tire can be seen. There is cord or fabric showing through the tire's rubber.
Page 428 Check that all wheel nuts are properly tightened. See Wheel Nut Torque under Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause a crash.
Page 429 The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple conditions including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. Tires will typically need to be replaced due to wear before they may need to be replaced due to age.
Page 430 GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size.
Page 431 The Tire and Loading Information Label indicates the original equipment tires on the vehicle. , for the label location and more information about the Tire and Loading Information label. If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics,...
Page 432 The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires.
Page 433 The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature...
Page 434 Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts. Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash.
Page 435 Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.
Page 436 But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly.
Page 437 Running the engine in Extended Range Mode in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in Extended Range Mode in an enclosed area that has no fresh air ventilation.
Page 438 The kit includes: A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gauge D. Pressure Deflation Button (If equipped) E. Tire Sealant Canister Sealant/Air Hose (Clear) G. Air Only Hose (Black) H. Power Plug Read and follow the safe handling instructions on the label adhered to the sealant canister.
Page 439 When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place.
Page 440 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter.
Page 441 11. Press the on/off button (B) to turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire; therefore, Steps 12 through 18 must be done immediately after Step 11.
Page 442 20. Wipe off any sealant from the wheel, tire, and vehicle. 21. Dispose of the used sealant canister (E) and sealant/air hose (F) assembly at a local dealer or in accordance with local state codes and practices. 22. Replace it with a new canister available from your dealer.
Page 443 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter.
Page 444 The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc. To remove the sealant canister: 1. Unwrap the sealant hose. 2.
Page 445 Jump starting is connecting jumper cables between the two vehicles to enable vehicle starting. If the Volt or another vehicle has a run down 12 volt battery, it can be jump started using good condition jumper cables. There are different procedures depending on if the Volt has a run down battery or another vehicle has a run down battery.
Page 446 If the Volt won't start, the 12 volt battery may be run down. To jump start the Volt use the underhood remote positive (+) and negative ( ) terminals. 1. The other vehicle used to jump start the Volt must have a 12 volt battery with a negative ground system.
Page 447 6. Check that the jumper cables do not have loose or missing insulation or a shock could result and the vehicles could be damaged. Before connecting the jumper cables, here are some basic things to know. Positive (+) jumper cable goes to positive (+) battery terminal or a remote positive (+) terminal if available.
Page 448 1. Disconnect the black negative ( ) jumper cable from the Volt. Do not let the other end of the cable touch anything until after the next step. 2. Disconnect the black negative ( ) jumper cable from the other vehicle with the good battery.
Page 449 4. Locate the positive (+) and negative ( ) terminals on the vehicle with the run down battery. 5. Locate the positive (+) and negative ( ) battery terminals on the Volt. The access cover is under the load floor access cover in the rear cargo area.
Page 450 3. Connect the black negative ( ) jumper cable to the negative ( ) battery terminal of the Volt. Do not let the other end touch anything until the next step. 4. Make the final connection to a heavy, unpainted metal engine part or to the remote negative ( ) terminal on the other vehicle with the run down battery.
Page 451 To load a vehicle onto a flatbed carrier: 1. The vehicle must be on a flat surface. 2. The front tires must be properly inflated. If necessary, move a rear tire to the front to replace a flat or damaged tire. 3.
Page 452 7. When the fascia has enough clearance to clear the flatbed, lower the flatbed, and finish pulling the vehicle onto the flatbed. 8. Secure the vehicle to the flatbed (B) using nonabrasive straps (A) through all four wheel openings and secure the straps to the flatbed (B).
Page 453 Recreational vehicle towing refers to towing the vehicle behind another vehicle such as a motor home. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground.
Page 454 The vehicle can be towed from the front using a dolly. To tow the vehicle using a dolly, follow these steps: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions. 2. Drive the front wheels onto the dolly.
Page 455 Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing the Vehicle later in this section. Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish.
Page 456 A. Outer Air Deflector B. Inner Air Deflector C. Tab D. Slot The front air deflector allows air to flow cleaner under the vehicle. Should the front air deflector become detached, insert Tab C into Slot D. Repeat for the other side. To preserve the finish, keep it clean by washing it often.
Page 457 Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft, clean cloth with mild soap and water.
Page 458 Use a stiff brush with tire cleaner to clean the tires. If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection.
Page 459 The interior will continue to look its best if it is cleaned often. Dust and dirt can accumulate on the upholstery and cause damage to the carpet, fabric, leather, and plastic surfaces. Stains should be removed quickly as extreme heat could cause them to set rapidly.
Page 460 Use a vacuum cleaner with a soft brush attachment to remove dust and loose dirt. A canister vacuum with rotating brushes in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda.
Page 461 Do not use silicone or wax-based products, or those containing organic solvents to clean the interior because they can alter the appearance by increasing the gloss in a non-uniform manner. To remove dust, a soft cloth dampened with water can be used.
Page 462 If a floor mat is the wrong size or is not properly installed, it can interfere with the accelerator pedal and/or brake pedal. Interference with the pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury.

Chevrolet 2011 Volt Owner's Manual

Bluetooth

Infotainment System

Quick Links

Chapters

Related Manuals for Chevrolet 2011 Volt

Summary of Contents for Chevrolet 2011 Volt

Table of Contents