Parts And Functions; Display Board - Haier AS09PBDHRA Operation Manual

Parts and Functions

• Indoor Unit
Inlet
Inlet grille
Horizon tal flap
丿 Vertical .blade
( adju st up and do w n air flo w ( ad j ust le ft and
Don't adjust it manually)

Display board

0
Setting temp.display
f)Operation mode indicator
8
Remote signal receiver
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
• WiFi Se tup
If your Air Cond几ioner (AC) has a Connected Appliance Information
label located under the front cover as shown below, your AC is
WiFi Connect Enabled. A WiFi communication card is built into the
product allowing it to communicate with your smart phone for remote
monitoring, control and notifications.
Please visit www.haier.com.au/smart or www.haier.co.nz/smart to
learn more about connected appliance featu「es, and to learn what
connected appliance apps will work with you
＠
Air Purif y ing Filter
{inside)
Display
board
Emergency
Switch
Outlet
ight air fl ow}
「
Control the lightening and
extinguishing of the indoor LED
display board.
蕴 ＠
1= 10 一
--
巳巳
跪
©
一
@OUTLET
@ INLET
@ CONNECTING PIPING
AND ELECTRICAL WIRING
@ DRAIN HOSE
smart phone.
「
• Remote controller
三I
J, � ,l:
念
＠）
®
＠
®
＠
＠
®
＠
远
＠
＠
＠
＠
＠
＠
。 。 。
＠
＠
＠
｀
coc,
U础 吐匀
@
器
�
1. Mode display
I I I I IH
Opera n mode AUTO DRY F T
沁 cocx.
Im 心 还
画 口
R 国 国
I 砌啦 如t �lle c
2. Signal sending display
3. SWING display
4. FAN SPEED display
I
Dis pla y
d-dll--1111
LO MED HI AUTO
5. LOCK display
6. TIMER OFF display
TIMER ON display
7. TEMP display
NOTE:
Cooling only unit do not have displays and functions related w ith heating
If the unit which you purchased has healthy function,follow it.If not,please ignore
• Loading of the battery
1
2
2 R-03 batteries, resetting key
3
cover again.
Note:
• The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
• When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
• Full display or unclear display during operation indicates the
batteries have been used up. Please change batteries.
• If the remote controller can't run normally during operation, please
remove the batteries and 「eload several minutes later.
8 . Additional functions display
Ope,atoo mode louiE计SLEEP ! HEAL TH I TURBO
Im
一名I
!Rem ote ooo 四叫 ""ii
9 . QUIET button
10.HEAT button
11.COOL button
12.AUTO button
13.FAN SPEED button
14.TIMER button
15.SELF CLEAN button
16.LOCK button
Used to lock buttons and LCD display
17.LIGHT button
Control the lightening and
extinguishing of the indoor LED
display board.
18. POWER ON/OFF button
19.DRY button
E
20.T MP button
21.SWING button
22.HOUR button
E C
23. XTRA FUN TION button
Function: Sleeping HEALTH（
C
UV- lamp starts working）-
Healthy airflow position1-Healthy
airflow position 2-Power -Air
sending-A-8 yard -- .- Left/Right
Swing(This function is unavailable
on some models.)
U M
24.CANCE CON FI button
R
Function: Setting and cancel to
the timer and other additional
functions.
25.RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote.
Remove the battery cover;
Load the batteries as illustrated.
Load the battery.then put on the