IDEAL APP SBE 80 Series Assembly Instruction

SBE
two pole battery connectors with option for auxiliary contacts.
Contains one (1) housing and two (2) contacts.
1. CONNECTOR RATINGS
Series
SBE80
SBO60
2. TOOLING CHART
Contact
Part Number" Size
1399G1
3. REDUCING BUSHING
Bushing
Part Number AWG (mm²)
5910
5912
4. CABLE STRIPPING DIMENSIONS FOR PRIMARY POWER CONTACTS
Connector
Series
SBE80 / SBO60
5. RECOMMENDED SOLDERING TECHNIQUES
(
Use rosin flux solder only). Wrap cable strands, melt solder into well; heat and insert stripped
cable. Continue heating well until solder flows into wire being careful not to over flow onto
contact surfaces. DO NOT SOLDER DIP CONTACTS when contacts are soldered to
unsupported lead. Underwriters' Laboratories, Inc. requires use of cable clamps, listed in table below.
Connector
Series
SBE80 / SBO60
6. CABLE / CONTACT & HOUSING ASSEMBLY
Observing polarity of markings, push each contact into rear of housing until notched side snaps
over spring, tug on cable to make sure contact is locked into place.
DISASSEMBLING CONNECTORS
Switch off power first. Remove contact by depressing spring with a small flat blade screwdriver
and pulling lightly on the cable.
CAUTION: Replace contacts individually on battery leads to reduce potential danger of shorting.
HEADQUARTERS: Anderson Power Products®, 13 Pratts Junction Road, Sterling, MA 01564-2305 USA T:978-
422-3600 F:978-422-0128 | EUROPE: Anderson Power Products® Ltd., Unit 3, Europa Court, Europa Boulevard,
Westbrook, Warrington, Cheshire, WA5 7TN United Kingdom T: +44 (0) 1925 428390 F: +44 (0) 1925 520203 | ASIA
/ PACIFIC: IDEAL Anderson Asia Pacific Ltd., Unit 922-928 Topsail Plaza, 11 On Sum Street, Shatin N.T., Hong Kong
T:+(852) 2636 0836 F:+(852) 2635 9036 | CHINA: IDEAL Anderson Technologies (Shenzhen) Ltd., Block A8 Tantou
Western Industrial Park, Songgang Baoan District, Shenzhen, PR. China 518105 T: +(86) 755 2768 2118 F: +(86) 755
2768 2218 | TAIWAN: IDEAL Anderson Asia Pacific Ltd., Taiwan Branch, 4F.-2, No.116, Dadun 20th St., Situn District,
Taichung City 407, Taiwan (R.O.C.) T: +(886) 4 2310 6451 F:+(886) 4 2310 6460 "
www.andersonpower.com
All Data Subject To Change Without Notice
& SBO
®
Assembly instruction for SBE
Amperes Volts AWG
80 150
60 600
Wire
16 mm
Wire Size
#10-12 (5.3 - 3.3)
#8 (8.4)
Strip "X" To
Inches
0.56
For Two Single
Conductor Cables
SBE80REDCLP-BK
15515
Connectors
®
80 & SBO
®
FOR INSTALLATION BY A QUALIFIED
ELECTRICIAN IN ACCOR
TIONAL AND LOCAL ELECTRICAL CODES AND
THE FOLLOWING INSTRUCTIONS. THE SUIT-
ABILITY OF THIS TYPE OF TERMINATION MUST
BE EVALUATED BY UNDERWRITERS' LABORA-
TORIES, INC. AND CANADIAN STANDARDS. AS-
SOCIATION FOR THE END USE APPLICATION:
Assemble contacts to the cables according to the
equipment manufacturer's assembly instructions.
The following instructions are supplied as a refer-
ence. Please note: instructions are included with each
crimp tool for proper use.
Max Cable Size
mm²
#6 16
#6 16
Pneumatic
Bench Tool + Die +
1387G1 1388G6
For Use With
Contact Part Number
1339G1
1399G1
mm
14
60 Series
®
DANCE WITH NA-
Locator or Tool
1389G9
X
1S6331 ASM-SBE/SBO REV 02
Hand
1309G4