Dump Screen; Dump (Write) Screen - Kenwood FZDA07ELEF2 Service Manual

FZDA07ELEF2/EREF2/MRHF2
11 Longitude
12 Item_Position (Only for Japan destination)
13 Item_Latitude (Except for Japan destination)
14 Item_Longitude (Except for Japan destination)
A Shift to "Engineering Diag Menu (Page1)" screen.

■ Dump screen

∗ The number of byte to be read is selectable from 1Byte,
2Byte and 4Byte.
Select 1Byte as a default value when shifting from "Engineer-
ing Diag Menu (Page1) screen", "DISK Information screen"
or "Developer Diag Menu (Page1) screen".
Retain the last value when shifting from "Dump (Output)
screen" (Selection of output media) by using the Return SW.
Retain the value that has been set up in "Dump (Write)
screen" when shifting from "Dump (Write) screen" (Dump list
writing screen) by using the Return SW.
A G
* 1
* 2
B 0824E00 1
D
0000 0000 0000
F
0000 0000 0000
0000 0000 0000
0000 0000 0000
0000 0000 0000
0000 0000 0000
0000 0000 0000
0000 0000 0000
Output
O
● Description of operations
1 Dump list
2 Pointer cursor
3 Pointer
A Set 1 in the number of byte to be read.
B Set 2 in the number of byte to be read.
C Set 4 in the number of byte to be read.
D Increase the pointer value.
E Decrease the pointer value.
F Move the pointer cursor to left.
G Move the pointer cursor to right.
H Display the preceding page.
I Display the succeeding page.
J Set the pointer value.
L Re-write the dumped value (Shift to "Dump (Write)"
screen)
M Shift to "Engineering Diag Menu (Page1)" screen.
Shift to "DISK Information" screen.(When shifting from
DISK Information screen.)
O Save in the external equipment (Shift to "Output Size
Select" screen).
30
TEST MODE
M
B E C J
Menu
2 4
0000 0000 0000 0000 0000
0000 0000 0000 0000 0000
0000 0000 0000 0000 0000
0000 0000 0000 0000 0000
0000 0000 0000 0000 0000
0000 0000 0000 0000 0000
0000 0000 0000 0000 0000
0000 0000 0000 0000 0000
Write
L

■ Dump (Write) screen

This screen is intended to write data in NAVI (internal
memory).
D
*
1
* 2
F FFFFFFF 1
*
4 3
0000 0000 0000
0000 0000 20FF
B
0000 0000 0000
0000 0000 0000
A Output
0 1 2 3
M
8 9 A B
5
Overwrite which memory area?
ROM
X
H
● Description of operations
1
1 Pointer
2 Pointer cursor
I
3 Dump list
4 Dump list cursor
A Save in the external equipment (Shift to "Output Size
Select" screen).
B Display "CRC Check" screen (On Screen).
C Set the pointer value.
D Set 1 in the number of byte to be read.
E Set 2 in the number of byte to be read.
F Set 4 in the number of byte to be read.
G Display the preceding page.
H Display the succeeding page.
I Move the pointer cursor up.
J Move the pointer cursor down.
K Move the pointer cursor to left.
L Move the pointer cursor to right.
M Enter the value, 0~F.
N Switch pointer and dump list inputs.
O Shift to "Dump" screen
5 On Screen frame
6 Message
X Write the message in ROM area.
Y Write the message in RAM area.
∗ After the completion of data writing, close the On Screen
window and display "Dump (Write)" screen again.
E F C
Back
2 4
0000 0000 0000 0000
0000 0000 0000 0000
0000 0000 0000 0000
0000 0000 0000 0000
Input charge
Write
4 5 6 7
C D E F
N K J
BACK SCREEN
RAM
O
G
0000
0000
0000
0000
H
I
L
6
Y