Page 1 2005 Cadillac DeVille Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-5 Safety Belts ... 1-7 Child Restraints ... 1-26 Airbag System ... 1-45 Restraint System Check ... 1-54 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest & Wreath, and the name DEVILLE are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without notice.
Page 3 Safety Warnings and Symbols There are a number of safety cautions in this book. We use a box and the word CAUTION to tell about things that could hurt you if you were to ignore the warning. CAUTION: These mean there is something that could hurt you or other people.
Page 4 Vehicle Damage Warnings Also, in this manual you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 5 These are some examples of symbols that may be found on the vehicle:...
Page 6 NOTES...
Page 7: Table Of Contents
Section 1 Front Seats ...1-2 Power Seats ...1-2 Power Lumbar ...1-2 Massaging Lumbar ...1-3 Heated and Cooled Seats ...1-3 Reclining Seatbacks ...1-4 Rear Seats ...1-5 Heated Seats ...1-5 Power Lumbar ...1-6 Safety Belts ...1-7 Safety Belts: They Are for Everyone ...1-7 Questions and Answers About Safety Belts ...1-11 How to Wear Safety Belts Properly ...1-12 Driver Position ...1-12...
Page 8: Front Seats
Front Seats Power Seats The power seat controls are located on the outboard sides of the front seat cushions. • Move the front of the seat control up or down to adjust the front portion of the cushion. • Move the rear of the seat control up or down to adjust the rear portion of the cushion.
Page 9: Massaging Lumbar
Massaging Lumbar If your vehicle has this feature, the control is located on the outboard sides of the front seats. With the ignition on, brieﬂy press the top of the control where it is marked AUTO to activate the massaging lumbar feature.
Page 10: Reclining Seatbacks
When you press a button, the feature will turn on at the highest setting. Each time you press the button, the feature will go down one temperature setting. To turn the feature off, keep pressing the button until the display lights turn off. Reclining Seatbacks The recliner controls are located on the outboard...
Page 11: Rear Seats
CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 12: Power Lumbar
(Heated Seat and Seatback): Press this button to turn on the heated seat and seatback. Press the button to turn on the feature that you want. A light on the button will display to show which feature is on. There are three temperature ranges for each feature. A light bar near the buttons will display which setting the feature is in;...
Page 13: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Do not let anyone ride where he or she can not wear a safety belt properly.
Page 14: Why Safety Belts Work
You never know if you will be in a crash. If you do have a crash, you do not know if it will be a bad one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Page 15 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop.
Page 16 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-10...
Page 17: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Will I be trapped in the vehicle after an accident...
Page 18: Driver Position
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt.
Page 19 3. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
Page 20 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. 1-14 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 21 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 22 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-16 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 23 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 24: Safety Belt Use During Pregnancy
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 25: Right Front Passenger Position
Right Front Passenger Position To learn how to wear the right front passenger’s safety belt properly, see Driver Position on page 1-12. The right front passenger’s safety belt works the same way as the driver’s safety belt — except for one thing.
Page 26: Rear Seat Passengers
To make the belt shorter, pull its free end as shown until the belt is snug. Buckle, position and release it the same way as the lap part of a lap-shoulder belt. If the belt is not long enough, see Safety Belt Extender on page 1-25. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 27 The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly. 2. Push the latch plate into the buckle until it clicks. The latch plates for the safety belts in each rear seating position vary in size.
Page 28 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 29 Rear Safety Belt Comfort Guides for Children and Small Adults Rear shoulder belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When installed on a shoulder belt, the comfort guide better positions the belt away from the neck and head.
Page 30 2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 1-24 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top.
Page 31: Safety Belt Pretensioners
4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-20. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
Page 32 Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. If you have the choice, a child should sit next to a window so the child can wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. 1-26 What is the proper way to wear safety belts? If possible, an older child should wear a...
Page 33 CAUTION: Never do this. Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck?
Page 34 CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 35 CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby does not weigh much — until a crash. During a crash a baby will become so heavy it is not possible to hold it. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) baby will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 36: Child Restraints
What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 37: Child Restraint Systems
CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 38 A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. 1-32 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
Page 39 A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness. A booster seat can also help a child to see out the window. How do child restraints work? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position...
Page 40: Where To Put The Restraint
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may ﬁnd these instructions on the restraint itself or in a booklet, or both.
Page 41: Top Strap
CAUTION: A child in a child restraint in the center front seat can be badly injured or killed by the right front passenger’s airbag if it inﬂates. Never secure a child restraint in the center front seat. It is always better to secure a child restraint in the rear seat.
Page 42 In Canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored. Anchor the top strap to one of the following anchor points.
Page 43: Top Strap Anchor Location
Top Strap Anchor Location Your vehicle has top strap anchors already installed for the rear seating positions. You will ﬁnd them behind the rear seat on the ﬁller panel. In order to get to a bracket, you will have to open the trim cover.
Page 44 A. Lower Anchorage B. Lower Anchorage C. Top Tether 1-38 A. Lower Anchorage B. Lower Anchorage In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback at each lower anchor position.
Page 45: Securing A Child Restraint Designed For The Latch System
The labels are located near the base of all three rear seating positions. CAUTION: If a LATCH-type child restraint is not attached to its anchorage points, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed.
Page 46: Securing A Child Restraint In A Rear Seat Position
Securing a Child Restraint in a Rear Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-37. See Top Strap on page 1-35 if the child restraint has one. CAUTION: A child in a child restraint in the center front seat can be badly injured or killed by the right...
Page 47 3. Buckle the belt. Be sure the latch plate clicks when you put it into the buckle. This means you are using the correct buckle. Also make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 4.
Page 48: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Center Front Seat Position CAUTION: A child in a child restraint in the center front seat can be badly injured or killed by the right front passenger’s airbag if it inﬂates. Never secure a child restraint in the center front seat. It is always better to secure a child restraint in the rear seat.
Page 49 Here is why: CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Always secure a rear-facing child restraint in a rear seat.
Page 50 5. Pull the rest of the lap belt all the way out of the retractor to set the lock. 1-44 6. To tighten the belt, feed the lap belt back into the retractor while you push down on the child restraint. You may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 51: Airbag System
Airbag System Your vehicle has airbags — a frontal airbag for the driver and another frontal airbag for the right front passenger. Your vehicle also has a side impact airbag for the driver and another side impact airbag for the right front passenger.
Page 52 CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt, even if you have airbags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it.
Page 53 CAUTION: Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 54: Where Are The Airbags
Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel. 1-48 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side.
Page 55 The driver’s side impact airbag is in the side of the driver’s seatback closest to the door. The right front passenger’s side impact airbag is in the side of the passenger’s seatback closest to the door. 1-49...
Page 56: When Should An Airbag Inﬂate
The side impact airbags for the rear seat outboard passenger positions are in the sides of the rear seatback closest to the doors. 1-50 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 57 Whether your frontal airbags will or should deploy is not based on how fast your vehicle is traveling. It depends largely on what you hit, the direction of the impact and how quickly your vehicle slows down. In addition, your vehicle has “dual stage” frontal airbags, which adjust the restraint according to crash severity.
Page 58: What Makes An Airbag Inﬂate
What Makes an Airbag Inﬂate? In an impact of sufficient severity, the airbag sensing system detects that the vehicle is in a crash. For both the frontal and side impact airbags, the sensing system triggers a release of gas from the inﬂator, which inﬂates the airbag.
Page 59 CAUTION: When an airbag inﬂates, there is dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so.
Page 60: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 7-11.
Page 61: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 62 NOTES 1-56...
Page 63: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry System ...2-5 Remote Keyless Entry System Operation ...2-6 Doors and Locks ...2-8 Door Locks ...2-8 Central Door Unlocking System ...2-9 Power Door Locks ...2-9 Programmable Automatic Door Locks ...2-10 Rear Door Security Locks ...2-10 Lockout Protection ...2-11 Trunk ...2-12 Windows ...2-15...
Page 64 Section 2 Full Floor Console Storage Area ...2-49 Center Console Storage Area ...2-49 Center Flex Storage Unit ...2-50 Map Pocket ...2-50 Assist Handles ...2-50 Umbrella Holder ...2-51 Features and Controls Rear Storage Area ...2-51 Rear Storage Door Trim Armrest ...2-51 Convenience Net ...2-51 Sunroof ...2-51 Vehicle Personalization ...2-52...
Page 65: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. If they turned the ignition to ACCESSORY or ON and moved the shift lever out of PARK (P), that would release the parking brake.
Page 66 Valet Key Be sure you have spare keys. In an emergency, contact Cadillac Roadside Assistance. See Roadside Service on page 7-5. If your vehicle is equipped with the OnStar an active subscription and you lock your keys inside the vehicle, OnStar unlock your vehicle.
Page 67: Remote Keyless Entry System
Remote Keyless Entry System Your keyless entry system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 68: Remote Keyless Entry System Operation
Remote Keyless Entry System Operation With this system you can lock and unlock your doors or unlock your trunk from about 3 feet (1 m) up to 30 feet (9 m) away using the remote keyless entry transmitter supplied with your vehicle. (Lock): Press this symbol to lock the doors.
Page 69: Battery Replacement
Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer.
Page 70: Doors And Locks
3. Insert the new battery as the instructions under the cover indicate. 4. Snap the transmitter back together tightly to be sure no moisture can enter. 5. Press any button on the remote keyless entry transmitter to resynchronize the transmitter. 6.
Page 71: Central Door Unlocking System
There are several ways to lock and unlock your vehicle. Because your vehicle has the theft-deterrent system, you must unlock the doors with the key or remote keyless entry transmitter to avoid setting off the alarm. From the outside, use either the key or the remote keyless entry transmitter.
Page 72: Programmable Automatic Door Locks
Press the bottom part of the power door lock switch located on either front door to lock all of the doors at once. Press the top of the switch to unlock all of the doors at once. If your vehicle has rear door lock switches, they can also lock all the doors at once by pressing the bottom part of the switch, but they cannot unlock the doors.
Page 73: Lockout Protection
When you want to open a rear door while the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, the front door power lock switch or by lifting the rear door manual lock. 2.
Page 74: Trunk
Trunk CAUTION: It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid:...
Page 75: Trunk Lid Tie Down
Trunk Lid Tie Down CAUTION: Driving with the trunk lid open can allow dangerous CO (carbon monoxide) gas to come into your vehicle. You can not see or smell CO. It can cause unconsciousness and even death. If you ever need to drive with your trunk lid open, then: •...
Page 76: Emergency Trunk Release Handle
Emergency Trunk Release Handle Notice: Using the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk may damage it. Use the emergency trunk release handle only to help you open the trunk lid. There is a glow-in-the-dark emergency trunk release handle located inside the trunk near the latch.
Page 77: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 78: Power Windows
Power Windows The power window switches are located on the armrest near each window. Press the up or down arrows on the switches to raise or lower the windows. Your vehicle has Retained Accessory Power (RAP) that allows you to use the power windows once the ignition has been turned off.
Page 79: Window Lockout
CAUTION: If express override is activated, the window will not reverse automatically. You or others could be injured and the window could be damaged. Before you use express override, make sure that all people and obstructions are clear of the window path. Express Window Override A condition may exist that causes auto-reversal of the window due to weather or an obstruction.
Page 80: Sun Visors
Sun Visors Swing down the primary visor to block out glare. It can also be detached from the center mount and moved to the side while the auxiliary sunshade remains to block the glare from the front. The visors also have side-to-side slide capability.
Page 81: Theft-Deterrent Systems
The rear power sunshade switch only works while the ignition is on or while the retained accessory power is active. See Ignition Positions on page 2-24. To raise the power sunshade, press and release the REAR SHADE switch located on the front overhead console.
Page 82: Testing The Alarm
If a door or the trunk is opened without a key or a remote keyless entry transmitter, the horn will sound and the lamps will ﬂash for about 30 seconds. Remember, the theft-deterrent system will not arm if you lock the doors with a key or use the manual door lock.
Page 83: Valet Lockout Switch
Valet Lockout Switch The valet lockout switch is located inside the glove box. Press the switch to ON to disable the use of the trunk, fuel door, garage door opener and optional cellular telephone. The remote keyless entry transmitter cannot open the trunk if the valet lockout switch is in ON.
Page 84: Pass-Key ® Iii
® PASS-Key III Operation Your vehicle is equipped with the PASS-Key (Personalized Automotive Security System) theft-deterrent system. PASS-Key theft-deterrent system. This means you do not have to do anything different to arm or disarm the system. It works when you insert or remove your key from the ignition.
Page 85 ® PASS-Key III system at this time. If you lose or damage a PASS-Key your dealer to have a new key made. In an emergency, contact Cadillac Roadside Assistance. See Roadside Service on page 7-5. ® III system, ® III key, contact...
Page 86: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one speed — fast or slow —...
Page 87: Retained Accessory Power (Rap)
A (OFF): This is the only position in which you can insert or remove the key. This position locks the ignition and transaxle. It is a theft-deterrent feature. B (ACCESSORY): This position allows you to use things like the radio and the windshield wipers when the engine is off.
Page 88: Starting Your Engine
Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N). The engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle.
Page 89: Engine Coolant Heater
Engine Coolant Heater Your vehicle may be equipped with an engine coolant heater. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 90: Automatic Transaxle Operation
Automatic Transaxle Operation The automatic transaxle may have a shift lever located either on the steering column or on the console between the seats. There are several different positions for the shift lever. Console Shifter Column Shifter (Digital and Analog Cluster similar) 2-28 PARK (P): This position locks the front wheels.
Page 91 Ensure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) while the ignition key is in ON.
Page 92 AUTOMATIC OVERDRIVE ( ): This position is for normal driving. If you need more power for passing, and you are: • Going less than 35 mph (55 km/h), push the accelerator pedal about halfway down. • Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
Page 93: Performance Shifting (Dts Only)
Performance Shifting (DTS Only) When your vehicle detects a change in driving conditions, it will automatically initiate the appropriate performance shift mode. When this occurs, the gear display on the instrument panel cluster will change to indicate that the transaxle has shifted to a different gear.
Page 94: Shifting Into Park (P)
Shifting Into Park (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 95: Leaving Your Vehicle With The Engine Running
Leaving Your Vehicle With the Engine Running CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre.
Page 96: Shifting Out Of Park (P)
Shifting Out of Park (P) Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is ON. See Automatic Transaxle Operation on page 2-28. The shift lock control system is designed to do the following: •...
Page 97: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell.
Page 98: Running Your Engine While You Are Parked
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 99: Mirrors
Mirrors Automatic Dimming Rearview Mirror ® with OnStar Your vehicle may have an automatic dimming rearview ® mirror with OnStar system controls. For more ® information about OnStar , see OnStar on page 2-42. When the automatic dimming feature is turned on, the mirror automatically changes to reduce glare from headlamps behind you.
Page 100: Compass Variance
Mirror Operation (On/Off): Press and hold the button, located on the lower left side of the mirror face, for about three seconds to turn the automatic dimming feature on or off. The indicator light will illuminate when this feature is active. The automatic dimming feature is active each time the vehicle is started.
Page 101: Cleaning The Mirror
To adjust for compass variance do the following: 1. Find the current location and variance zone number on the following zone map. 2. Press and hold the on/off button until a zone number appears in the display. 3. Once the zone number appears in the display, press the on/off button quickly until the correct zone number appears in the display.
Page 102: Outside Power Mirrors
Outside Power Mirrors The control on the driver’s door armrest operates both outside rearview mirrors. Press (R) on the selector switch to choose the right mirror or (L) to choose the left mirror. The center position is off and will not allow the mirrors to move if the control pad is touched.
Page 103: Outside Automatic Dimming Mirror
Outside Automatic Dimming Mirror If the vehicle is equipped with this feature, the driver’s side mirror will adjust for the glare of headlamps behind you. This feature is controlled by the on and off settings on the automatic dimming rearview mirror. See Automatic Dimming Rearview Mirror with OnStar on page 2-37.
Page 104: Onstar System
® OnStar System ® OnStar uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services. ® A complete OnStar user’s guide and the terms and ®...
Page 105: Steering Wheel Controls
® OnStar Personal Calling ® As an OnStar subscriber, the Personal Calling capability is a hands-free wireless phone that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. ®...
Page 106: Homelink Transmitter
® HomeLink Transmitter ® HomeLink , a combined universal transmitter and receiver, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems and home lighting. Additional ®...
Page 107: Programming The Homelink
Programming the HomeLink Transmitter ® Do not use the HomeLink Transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the ®...
Page 108 3. Simultaneously press and hold both the desired ® button on HomeLink and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming”...
Page 109: Gate Operator And Canadian Programming
Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to “time out” or quit after several seconds of transmission. This may not be long enough for ® HomeLink to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to “time out”...
Page 110: Storage Areas
Reprogramming a Single HomeLink Button To program a device to HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the HomeLink button, proceed with Step 2 under “Programming ®...
Page 111: Front Storage Area
Front Storage Area If your vehicle is equipped with the front storage area, it comes with a coinholder, a storage compartment, an optional cellular telephone and a dual cupholder. Full Floor Console Storage Area If your vehicle is equipped with the full ﬂoor console, it has an upper and lower storage area.
Page 112: Center Flex Storage Unit
Center Flex Storage Unit Your vehicle may be equipped with a center ﬂex storage unit that includes a front center seat with a lap belt and an underseat storage compartment. The center seatback can also be used as a fold down armrest with extra space for CDs or tapes.
Page 113: Umbrella Holder
Umbrella Holder The passenger’s front seat cushion is equipped with an umbrella holder. Gently slide the umbrella into the slot located under the front portion of the passenger’s seat cushion. Rear Storage Area Your vehicle is equipped with a rear seat armrest which includes an open storage compartment and a dual cupholder.
Page 114: Vehicle Personalization
Press and release the ROOF switch rearward to the second position to express-open the glass panel to the comfort stop position, approximately half-way open. The comfort stop position is designed to help reduce noise and make the rear seat passengers more comfortable. The glass panel may then be fully opened by pressing the ROOF switch again.
Page 115 To save your positions in memory, do the following: 1. Adjust the driver’s seat, including the seatback recliner and lumbar, both outside mirrors and the steering wheel to a comfortable position. 2. Press and hold button 1. After a brief delay, two beeps will sound through the driver’s side front speaker to let you know that the position has been stored.
Page 116 To stop recall movement of the memory feature at any time, press one of the power seat controls or memory buttons. To store the exit position for an easy exit, do the following: 1. Recall the driver position by pressing button 1, or by pressing the unlock button on the remote keyless entry transmitter 1.
Page 117 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Power Tilt Wheel and Telescopic Steering Column ...3-7 Heated Steering Wheel ...3-7 Turn Signal/Multifunction Lever ...3-8 Turn and Lane-Change Signals ...3-8 Headlamp High/Low-Beam Changer ...3-9 Flash-to-Pass ...3-9 Windshield Wipers ...3-9...
Page 118 Section 3 Anti-Lock Brake System Warning Light ...3-48 Traction Control System (TCS) Warning Light ...3-48 Engine Coolant Temperature Warning Light ...3-49 Engine Coolant Temperature Gage ...3-49 Malfunction Indicator Lamp ...3-50 Oil Pressure Light ...3-53 Security Light ...3-53 Fog Lamp Light ...3-54 Lights On Reminder ...3-54 Cruise Control Light ...3-54 Highbeam On Light ...3-54...
Page 119 NOTES...
Page 120: Instrument Panel Overview
Instrument Panel Overview...
Page 121 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-34. B. Fog Lamp Button (If Equipped). See Fog Lamps on page 3-18. C. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-8. ®...
Page 122: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located near the center of the instrument panel.
Page 123: Power Tilt Wheel And Telescopic Steering Column
Power Tilt Wheel and Telescopic Steering Column If your vehicle has this feature, the power tilt wheel control is located on the outboard side of the steering column. To operate the power tilt feature, push the control up and the steering wheel will tilt up. Push the control down and the steering wheel will go down.
Page 124: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 3-8 • Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-9 •...
Page 125: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer Push forward to change the headlamps from low beam to high. Pull the lever back and then release it to change from high beam to low. This light on the instrument panel cluster will be on, indicating high-beam usage.
Page 126: Rainsense™ Ii Wipers
OFF: Turn the band to OFF to turn off the wipers. Be sure to clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, carefully loosen or thaw them. If the blades do become damaged, get new blades or blade inserts.
Page 127: Windshield Washer
Notice: Going through an automatic car wash with the wipers on can damage them. Turn the wipers off when going through an automatic car wash. The MIST and wash cycles operate as normal and are not affected by the Rainsense™ II function. The Rainsense™...
Page 128: Cruise Control
Cruise Control With cruise control, you can maintain a speed of approximately 25 mph (40 km/h) or more without keeping your foot on the accelerator. This is helpful on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h).
Page 129 The buttons to operate cruise control are located on the steering wheel. 1. Press the CRUISE ON/OFF button, located on the bottom left of the steering wheel, to turn cruise control on. An indicator light will come on to show that the cruise control is on.
Page 130 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press the SET/CST button, then release the button and the accelerator pedal. You will now cruise at the higher speed.
Page 131: Exterior Lamps
Exterior Lamps The exterior lamp control is located to the left of the steering wheel on the instrument panel. (Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps. The exterior lamp control has three positions: (Off): Turn the control to this position to turn off all lamps except the Daytime Running Lamps (DRL).
Page 132: Wiper Activated Headlamps
Wiper Activated Headlamps This feature activates the headlamps and parking lamps after the windshield wipers have been in use for approximately six seconds. To operate, the Twilight ® Sentinel feature must be turned on. When the exterior lamp control is in the off position or parking lamp position and the wiper control is on delay, LO or HI, the HEADLAMPS SUGGESTED message will appear on the Driver Information Center (DIC).
Page 133 ® When the Twilight Sentinel lever is on and it is dark enough outside, the low-beam headlamps at reduced intensity will turn off and normal low-beam headlamp operation will occur. ® When the Twilight Sentinel lever is on and it is bright enough outside, the regular lamps will go off, and the low-beam headlamps at reduced brightness will take over.
Page 134: Fog Lamps
Fog Lamps If your vehicle has fog lamps, use them for better vision in foggy or misty conditions. The fog lamp button is located to the left of the steering wheel on the instrument panel. When you press the fog lamp button, a fog lamp symbol in the button and the fog lamp light on the instrument panel cluster will come on to indicate that the fog lamps and the parking lamps are on.
Page 135: Light Sensor
If you move the lever all the way to the right, the lamps will remain on for approximately three minutes after the ignition has been turned to OFF. If you move the lever so it is barely on, the lamps will go off quickly when you turn the ignition switch out of OFF.
Page 136: Exterior Lighting Battery Saver
Exterior Lighting Battery Saver If the manual parking lamps or headlamps have been left on, the exterior lamps will turn off approximately 10 minutes after the ignition is turned to OFF. This protects against draining the battery in case you have accidentally left the headlamps or parking lamps on.
Page 137: Courtesy Lamps
Courtesy Lamps The courtesy lamps are located on the headliner above the rear seat. These lamps come on by turning the instrument panel brightness knob fully clockwise or when any door is opened and it is dark outside. Puddle lamps are located on the bottom of the front and rear door trim.
Page 138: Reading Lamps
Reading Lamps The reading lamps are located on the overhead console on the headliner and in the rear door opening. These lamps come on automatically when any door is opened and it is dark outside. For manual operation, press the button to turn them on. Press it again to turn them off.
Page 139: Inadvertent Power Battery Saver
Inadvertent Power Battery Saver This feature is designed to protect your vehicle’s battery against drainage from the interior lamps, trunk lamp, glove box lamp, or the garage door opener. When the ignition is turned off, the power to these features will automatically turn off after 10 minutes (three minutes if a new car has 15 miles (24 km) or less).
Page 140 The controls for this feature are located to the left of and below the steering wheel. They are used to adjust the brightness and location of the image. Adjust the IMAGE control so the image is as low as possible while remaining visible.
Page 141 In dry, clear weather, the system can see pedestrians, animals, and the direction of the road ahead. In light rain, light snow, or light fog the image may not be as clear and you may not be able to see the direction of the road ahead.
Page 142: Ultrasonic Rear Parking Assist (Urpa)
Ultrasonic Rear Parking Assist (URPA) Your vehicle may be equipped with Ultrasonic Rear Parking Assist (URPA). URPA is designed to help you park while in REVERSE (R) and operates only at speeds less than 3 mph (5 km/h). URPA can help you avoid colliding with objects such as parked vehicles.
Page 143 The URPA display is located inside the vehicle, above the rear window. It has three color-coded lights that can be seen through the rearview mirror or by turning around. How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R).
Page 144: Accessory Power Outlets
It may also ﬂash red if the ultrasonic sensors are not kept clean. So be sure to keep your rear bumper free of mud, dirt, snow, ice and slush or materials such as paint or the system may not work properly. If after cleaning the rear bumper and driving forward at least 15 mph (25 km/h), the display continues to ﬂash red, see your dealer.
Page 145: Ashtrays And Cigarette Lighter
Follow the proper installation instructions that are included with any electrical equipment you install. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.
Page 146: Climate Controls
Climate Controls Dual Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Automatic Operation AUTO (Automatic): When this button is pressed and the temperature is set, the system will automatically control the inside temperature, the air delivery mode and the fan speed.
Page 147 Manual Operation MODE : Pressing the MODE switch and changing the mode cancels automatic operation and places the system in manual mode. Press AUTO to return to automatic operation. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 148 PASS TEMP (Passenger’s Temperature): Press this switch to turn the passengers’ climate control systems on. Press this switch to manually increase or decrease the temperature for the front passenger. PASS OFF (Passenger’s Climate Control): Press this button to turn all passenger climate control systems off. If the passenger’s temperature switch is turned off, the driver’s temperature knob will control the temperature for the entire vehicle.
Page 149: Defogging And Defrosting
Sensors The solar sensor on your vehicle monitors the solar radiation and the air inside your vehicle, then uses the information to maintain the selected temperature by initiating needed adjustments to the temperature, the fan speed and the air delivery system. The system may also supply cooler air to the side of the vehicle facing the sun.
Page 150: Outlet Adjustment
FRONT (Defrost): Pressing FRONT directs most of the air to the windshield and the side window outlets, with some air directed to the ﬂoor outlets. In this mode, the system will automatically turn off recirculation and run the air-conditioning compressor, unless the outside temperature is at or below freezing.
Page 151: Rear Climate Control System
Rear Climate Control System Your vehicle has a rear climate-control system that allows the rear-seat passengers to adjust the direction of the airﬂow, the fan speed and the temperature for the rear-seating area. This system also works with the main climate-control system in your vehicle. The control panel for this system is located on the back of the center console.
Page 152: Passenger Compartment Air Filter
(Bi-Level): This mode directs half the air to the upper outlets, and then directs the remaining air to the ﬂoor outlets. (Floor): This mode directs the air to the ﬂoor outlets. (Fan): Pressing this switch cancels automatic operation and places the system in manual mode. Press this switch to increase or decrease the fan speed.
Page 153 To access the passenger compartment air ﬁlter, do the following: 1. Use a tool to gently pry the cover up. If your vehicle has tabs that allow you to unlatch the cover with your ﬁngers, you will not need a tool for this step. 2.
Page 154: Steering Wheel Climate Controls
3. To remove the air ﬁlter, insert a tool between the air ﬁlter and the compartment wall on the outboard side of the vehicle. Then, push in to ﬂatten the pin holding the air ﬁlter in place. Gently remove the air ﬁlter and any loose debris that may be inside the air ﬁlter compartment.
Page 155: Climate Controls Personalization
Climate Controls Personalization If your vehicle is equipped with this feature, you can store and recall climate control settings for the temperature, the fan speed and the direction of the airﬂow. Memory buttons 1 and 2 are located on the driver’s door panel and correspond to the numbers 1 or 2 found on the back of each remote keyless entry transmitter.
Page 156: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 157: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using and many of the other things you will need to know to drive safely and economically.
Page 158 Analog Cluster United States version shown, Canada similar 3-42...
Page 159: Speedometer And Odometer
Speedometer and Odometer The speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). You may wonder what happens if a vehicle has to have a new odometer installed.
Page 160: Tachometer (Analog Cluster Only)
English/Metric Button By pressing this button located to the left of the steering wheel on the instrument panel, you can go back and forth from English (miles) to metric (kilometers). Other readings such as temperature, fuel and trip odometer also go back and forth between English and metric.
Page 161: Safety Belt Reminder Light
Safety Belt Reminder Light When the key is turned to ON or START, a chime will come on for several seconds to remind people to fasten their safety belts. The safety belt light will also come on and stay on for several seconds.
Page 162: Charging System Light
If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly.
Page 163: Brake System Warning And Parking Brake Indicator Light
Brake System Warning and Parking Brake Indicator Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem.
Page 164: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Light With the anti-lock brake system, the light(s) will come on when your engine is started and may stay on for several seconds. That is normal. If the light stays on, turn the ignition to OFF. Or, if the light comes on when you are driving, stop as soon as possible and turn the ignition off.
Page 165: Engine Coolant Temperature Warning Light
The traction control system warning light may come on for the following reasons: • If there is a brake system problem that is speciﬁcally related to traction control, the traction control system will turn off and the warning light will come on. •...
Page 166: Malfunction Indicator Lamp
This gage shows the engine coolant temperature. If the gage pointer moves into the shaded area, the engine is too hot. Digital Cluster That reading means the same thing as the warning light — the engine coolant has overheated. See Engine Overheating on page 5-27.
Page 167: If The Light Is Flashing
Notice: If you keep driving your vehicle with this light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty.
Page 168: If The Light Is On Steady
If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling Your Tank on page 5-7. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 169: Maintenance Schedule
This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your GM dealer can prepare the vehicle for inspection.
Page 170: Fog Lamp Light
Fog Lamp Light The fog lamps light will come on when the fog lamps are in use. The light will go out when the fog lamps are turned off. See Fog Lamps on page 3-18 for more information. Lights On Reminder United States Canada (Analog Only) This light comes on whenever the parking lamps are on...
Page 171: Fuel Gage
Fuel Gage Analog (United States) The fuel gage shows approximately how much fuel is in the tank. It works only when the ignition is in ON. Digital Cluster If the fuel supply gets down to about 1.8 gallons (7 L) of fuel remaining in the tank, the FUEL LEVEL LOW message will appear on the Driver Information Center (DIC) and a single chime will sound.
Page 172: Fuel Data Display (Digital Cluster Only)
Fuel Data Display (Digital Cluster Only) The fuel data display tells you all you about the fuel economy and how far you can travel with the fuel remaining. The average fuel economy (AVG) display shows the average miles per U.S. gallon. 3-56 To reset the average fuel economy, press the INFO button until the MPG AVG is displayed on the DIC.
Page 173: Driver Information Center (Dic)
Driver Information Center (DIC) This display gives you the status of many of your vehicle’s systems. The DIC is also used to display driver personalization features and warning/status messages. All messages will appear in the DIC display, located at the bottom of the instrument panel cluster. DIC Controls and Displays The Driver Information Center (DIC) buttons are located to the right of the steering wheel on the instrument...
Page 174 • AVG MPH (Average Miles per Hour): This message shows the average speed you have traveled at since the last time you reset the value. To reset the value, press the INFO button to display AVG MPH, then press and hold the INFO RESET button until 0.0 AVG MPH is displayed.
Page 175 ON/OFF: Pressing this button turns the Programming and Personalization Features on and off. FEATURE PROGRAMMING must be displayed on the DIC to begin actual programming. This button also starts and stops the timer. MILES RANGE: (Analog Cluster only) This message shows about how many miles you can drive without reﬁlling your fuel tank.
Page 176: Dic Warnings And Messages
DIC Warnings and Messages These messages will appear if there is a problem sensed in one of your vehicle’s systems. Vehicles that are ﬁrst sold in Canada will have a number after each message. This number helps to identify the problem.
Page 177 BATTERY VOLTAGE LOW – 6: This message will appear when the electrical system is charging less than 10 volts or if the battery has been drained. If this message appears immediately after starting, it is possible that the generator can still recharge the battery. The battery should recharge while driving but may take a few hours to do so.
Page 178 CHECK GAS CAP – 61: This message will appear if the gas cap has not been fully tightened. You should recheck your gas cap to ensure that it is on properly. CHECK OIL LEVEL – 36: For correct operation of the low oil sensing system, your vehicle should be on a level surface.
Page 179 CAUTION: When the CHECK TIRE PRESSURE message is displayed on the Driver Information Center and the tire pressure is low, your vehicle’s handling capabilities will be reduced during severe maneuvers. If you drive too fast, you could lose control of your vehicle. You or others could be injured.
Page 180 ENGINE HOT–AC OFF – 16: This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor is automatically turned off. When the coolant temperature returns to normal, the A/C operation will automatically resume.
Page 181 PASSENGER DOOR AJAR – 141: The right front passenger’s door is open or ajar when this message appears. The ignition must be in ON and the transaxle not in PARK (P) for this message to display. A chime will sound if the vehicle’s speed is greater than 3 mph (5 km/h).
Page 182 SERVICE SUSPENSION SYS – 84: This message is displayed to indicate that the suspension system is not operating properly. To correct this problem, have your vehicle serviced by your GM dealer. SERVICE THEFT SYSTEM – 34: This message means there is a problem with the PASS-Key fault has been detected in the system which means that the system is disabled and is not protecting the vehicle.
Page 183 THEFT ATTEMPTED – 40: This message is displayed if the theft system has detected a break-in attempt while you were away from your vehicle. TOP SPEED FUEL CUT-OFF – 111: This message will appear when the Powertrain Control Module (PCM) detects that the maximum speed for your vehicle has been reached.
Page 184: Climate Controls And Radio System Personalization
Climate Controls and Radio System Personalization These features allow both drivers to personalize their own climate control settings as well as their radio settings. For more information, see Climate Controls Personalization on page 3-39 and Radio Personalization with Home and Away Feature on page 3-102. DIC Vehicle Personalization Your vehicle is equipped with personalization capabilities that allows you to program certain features to a preferred...
Page 185 Remote Recall Memory If your vehicle has the optional memory package, you will have this feature. This feature recalls any previously programmed seat and mirror controls when the unlock button on the remote keyless entry transmitter is pressed. The telescoping steering column (if equipped) will return to its programmed position when the key is inserted in the ignition switch and turned to ON.
Page 186: Auto Exit Seat
Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, do the following: 1.
Page 187: Auto Exit Steering Wheel
The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. Auto Exit Steering Wheel If your vehicle has the optional memory package, you may have this feature also.
Page 188 Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, do the following: 1.
Page 189: Horn Sounds At Lock
The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. Horn Sounds at Lock This feature sounds the horn once when the remote keyless entry transmitter is used to lock the vehicle.
Page 190 Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, do the following: 1.
Page 191: Driver Unlock Key Off
Driver Unlock in PARK (P) This feature allows the driver’s door to automatically unlock when the vehicle is shifted into PARK (P). All other doors will remain locked until the unlock button on either front door armrest or on the remote keyless entry transmitter is pressed.
Page 192 3. To turn on the feature, press the ON/OFF button until ON appears on the DIC display. To turn it off, press the ON/OFF button until OFF appears on the display. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
Page 193: Tire Pressure Display
3. To turn on the feature, press the ON/OFF button until ON appears on the DIC display. To turn it off, press the ON/OFF button until OFF appears on the display. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
Page 194 Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, do the following: 1.
Page 195: Trip Computer
Trip Computer Oil Life Indicator This feature lets you know when to change the engine oil. It is based on the engine oil temperatures and your driving patterns. To see the display, press the INFO button several times until ENGINE OIL LIFE appears. If you see 99% ENGINE OIL LIFE, 99 percent of your current oil life remains.
Page 196: Setting The Time For Radios Without Radio Data Systems (Rds)
Setting the Time for Radios without Radio Data Systems (RDS) Press and hold HR until the correct hour appears on the display. Press and hold MN until the correct minute appears on the display. Display the time with the ignition off by pressing one of these buttons.
Page 197: Playing The Radio
Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. Finding a Station BAND: Press this button to switch between weather, FM1, FM2, AM, or XM1 or XM2 (if equipped). The display will show the selection.
Page 198 Setting the Tone (Bass/Treble) TONE: Press and release this button until BASS, TREBLE, or MIDRANGE appears on the display. The radio keeps separate tone settings for each band, preset, and source. LEVEL +: After selecting the desired tone control, press the plus or minus button to select the desired level.
Page 199 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. XM Updating Updating encryption code No XM signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) Channel Off Air Channel not in service Channel Unavail...
Page 200 Radio Display Message No CAT Info Category Name not available Not Found No channel available for the chosen category No Information No Text/Informational message available XM Theftlocked Theft lock active XM Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Check XM Receiver...
Page 201: Playing A Cd
Playing a CD Insert a CD partway into the slot, label side up. The player will pull it in. If the ignition and the radio are on and the underlined CD symbol appears on the display, the CD will begin playing. A CD may be loaded with the radio off but it will not start playing until the radio is on.
Page 202 SCAN: Press this button to listen to tracks for a few seconds. The CD will go to a track, play for a few seconds, then go on to the next track. Press this button again to stop scanning. SOURCE: Press this button to select a CD when listening to the radio.
Page 203: Radio With Cassette And Cd
Radio with Cassette and CD Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: •...
Page 204 Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. AVC (Automatic Volume Control): With AVC, the audio system adjusts automatically to make up for road or wind noise as you drive.
Page 205 Setting Preset Stations The RDS PTY mode must be off to set preset stations. Up to 36 stations (six weather, six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped), can be programmed on the six numbered pushbuttons, by performing the following steps: 1.
Page 206 Using Digital Signal Processing (DSP) DSP: This feature is used to provide a choice of four different listening experiences: talk, front seat, ambience, and spacious. DSP can be used while listening to the radio, cassette, CD, or XM™. Press this button to turn DSP on. Press and release this button until the desired selection appears on the display.
Page 207: Rds Messages
SCAN: Scan the stations within a PTY by performing the following: 1. Press PTY to activate program type select mode. PTY will appear on the display. 2. Press LEVEL to select a PTY. 3. Once the desired PTY is displayed, press SCAN, and the radio will begin scanning the stations in the PTY.
Page 208 For XM™ (if equipped), press the MSG button while in XM mode to retrieve four different categories of information related to the current song or channel: Artist Name/Feature, Song/Program Title, Channel Category. Each of the four information types may have multiple pages of text.
Page 209 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. XM Updating Updating encryption code No XM signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) Channel Off Air Channel not in service Channel Unavail...
Page 210 Radio Display Message No CAT Info Category Name not available Not Found No channel available for the chosen category No Information No Text/Informational message available XM Theftlocked Theft lock active XM Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Check XM Receiver...
Page 211: Playing A Cassette Tape
Playing a Cassette Tape The tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapes longer than that are so thin they may not work well in this player. The longer side with the tape visible should face to the right.
Page 212: Cassette Tape Messages
¦ ¥ SEEK : The tape must have at least three seconds of silence between each selection for SEEK to work. Press the up or the down arrow to seek to the next or to the previous selection on the tape. SCAN: Press this button to listen to each selection for a few seconds.
Page 213 Playing a CD Insert a CD partway into the slot, label side up. The player will pull it in and the CD should begin playing. If you want to insert a CD when the ignition is off, ﬁrst press the eject button or push the RCL knob. If the ignition or radio is turned off with the CD in the player, it will stay in the player.
Page 214 SCAN: Press this button to listen to each track for a few seconds. The CD will go to a track, play for a few seconds, then go on to the next track. Press this button again to stop scanning. SOURCE: Press this button to play a cassette tape or CD when listening to the radio.
Page 215: Navigation/Radio System
Navigation/Radio System Your vehicle may have a navigation radio system that includes Radio Data System (RDS) with Program Type (PTY) selections that will seek out the kind of music you want to listen to and XM™ Satellite Radio Service capabilities (if equipped). The radio can also communicate with the navigation system to broadcast announcements on traffic, weather, and emergency alert communications.
Page 216 Once you have loaded the CDs in the magazine, slide open the door of the CD changer. Push the magazine into the changer in the direction of the arrow marked on top of the magazine. 3-100 Close the door by sliding it all the way to the right. When the door is closed, the changer will begin checking for CDs in the magazine.
Page 217 ¦ 1 PREV (Previous) / TUNE SEEK pushbutton or the up arrow to go to the previous track on the CD. If playing the ﬁrst track of the CD, press this pushbutton or the up arrow to go to the last track of the CD.
Page 218: Radio Personalization With Home And Away Feature
CD Messages CD CHANGER ERROR: This message may appear on the display for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smoother, the CD should play.
Page 219: Theft-Deterrent Feature
With the radio off and the time displayed, use fast forward and reverse to select home or away presets. To select the away presets, press and hold FF for ﬁve seconds until you hear a beep. The next time the radio comes on, the away presets will be active.
Page 220: Radio Reception
Radio Reception The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. Static can occur on AM stations caused by things like storms and power lines. Try reducing the treble to reduce this noise.
Page 221 The tape player should be cleaned regularly after every 50 hours of use. The radio may display CLEAN TAPE to indicate that the tape player has been used for 50 hours without resetting the tape clean timer. If this message appears on the display, the cassette tape player needs to be cleaned.
Page 222: Care Of Your Cds
Care of Your CDs Handle CDs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a CD is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
Page 223: Xm™ Satellite Radio Antenna System
Notice: Do not try to clear frost or other material from the inside of the front windshield and rear window with a razor blade or anything else that is sharp. This may damage the rear window defogger grid and affect your radio’s ability to pick up stations clearly.
Page 224 NOTES 3-108...
Page 225: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunken Driving ...4-2 Control of a Vehicle ...4-5 Braking ...4-5 Anti-Lock Brake System (ABS) ...4-6 Braking in Emergencies ...4-8 Traction Control System (TCS) ...4-8 Continuous Variable Road Sensing Suspension (CVRSS) ...4-10 Steering ...4-10 Off-Road Recovery ...4-12...
Page 226: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-7. Defensive driving really means “be ready for anything.”...
Page 227 Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 16,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with more than 300,000 people injured.
Page 228 It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
Page 229: Control Of A Vehicle
CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Please do not drink and drive or ride with a driver who has been drinking.
Page 230: Anti-Lock Brake System (Abs)
Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking.
Page 231 Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each front wheel and at both rear wheels.
Page 232: Braking In Emergencies
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 233 United States This warning light will come on to let you know if there is a problem with your traction control system. See Traction Control System (TCS) Warning Light on page 3-48. When this warning light is on, the system will not limit wheel spin.
Page 234: Continuous Variable Road Sensing Suspension (Cvrss)
The traction control system monitors the front brake rotor temperature. If the traction control system comes on while the front brake rotors are hot due to heavy use of braking or previous traction control, the TRACTION SUSPENDED message will be displayed – but the system will not turn off right away.
Page 235: Steering In Emergencies
The traction you can get in a curve depends on the condition of your tires and the road surface, the angle at which the curve is banked, and your speed. While you are in a curve, speed is the one factor you can control. Suppose you are steering through a sharp curve.
Page 236: Off-Road Recovery
An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Page 237: Passing
Passing The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again. A simple maneuver? Not necessarily! Passing another vehicle on a two-lane highway is a potentially dangerous move, since the passing vehicle occupies the same lane as oncoming traffic for several seconds.
Page 238: Loss Of Control
• Check your mirrors, glance over your shoulder, and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your inside mirror, activate your right lane change signal and move back into the right lane.
Page 239 A cornering skid is best handled by easing your foot off the accelerator pedal. Remember: Any traction control system helps avoid only the acceleration skid. If your traction control system is off, then an acceleration skid is also best handled by easing your foot off the accelerator pedal.
Page 240: Driving At Night
Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. 4-16 Here are some tips on night driving. •...
Page 241: Driving In Rain And On Wet Roads
You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to re-adjust to the dark. When you are faced with severe glare, as from a driver who does not lower the high beams, or a vehicle with misaimed headlamps, slow down a little.
Page 242 The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking.
Page 243: Driving Through Flowing Water
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Page 244: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. 4-20 Here are ways to increase your safety in city driving: •...
Page 245: Freeway Driving
Freeway Driving Mile for mile, freeways — also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 246: Before Leaving On A Long Trip
Expect to move slightly slower at night. When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. The exit ramp can be curved, sometimes quite sharply.
Page 247: Highway Hypnosis
Highway Hypnosis Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 248 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system, and transaxle.
Page 249: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your trunk. Also see Tires on page 5-57. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning triangles.
Page 250: Driving On Snow Or Ice
Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You will have a lot less traction, or grip, and will need to be very careful.
Page 251: If You Are Caught In A Blizzard
Your anti-lock brakes improve your vehicle’s stability when you make a hard stop on a slippery road. Even though you have the anti-lock braking system, you will want to begin stopping sooner than you would on dry pavement. See Anti-Lock Brake System (ABS) on page 4-6.
Page 252 • Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, ﬂoor mats — anything you can wrap around yourself or tuck under your clothing to keep warm. You can run the engine to keep warm, but be careful.
Page 253: If You Are Stuck: In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 254: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. You should turn your traction control system off. See Traction Control System (TCS) on page 4-8. Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible.
Page 255 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Page 256 Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
Page 257 Example 2 Item Description Vehicle Capacity Weight for Example 2 Subtract Occupant Weight 150 lbs (68 kg) Available Cargo Weight Total Item 1,000 lbs (453 kg) 750 lbs (340 kg) 250 lbs (113 kg) Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating positions.
Page 258 Certiﬁcation Label A vehicle speciﬁc Certiﬁcation label is attached to the rear edge of the driver’s door. This label shows the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel and cargo. Never exceed the GVWR for your vehicle, or the Gross Axle Weight Rating (GAWR) for either the front or rear axle.
Page 259: Towing
If you put things inside your vehicle, like suitcases, tools, packages, or anything else, they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or...
Page 260: Dolly Towing
Here are some important things to consider before you do recreational vehicle towing: • What is the towing capacity of the towing vehicle? Be sure you read the tow vehicle manufacturer’s recommendations. • How far will you tow? Some vehicles have restrictions on how far and how long they can tow.
Page 261: Towing A Trailer
Towing a Trailer The Cadillac Professional Vehicle cannot tow a trailer. CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all.
Page 262: If You Do Decide To Pull A Trailer
7,200 lbs (3 273 kg). You can ask your dealer for our trailering information or advice, or you can write us at: Cadillac Customer Assistance Center Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169...
Page 263: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 264: Safety Chains
Hitches It is important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why you will need the right hitch. Here are some rules to follow: • The rear bumper on your vehicle is not intended for hitches.
Page 265: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you will want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself.
Page 266: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer When you tow a trailer, your vehicle may need a different turn signal ﬂasher and/or extra wiring. Check with your dealer. The arrows on your instrument panel will ﬂash whenever you signal a turn or lane change.
Page 267: Maintenance When Trailer Towing
But if you ever have to park your rig on a hill, here is how to do it: 1. Apply your regular brakes, but do not shift into PARK (P). 2. Have someone place chocks behind the trailer wheels. 3. When the wheel chocks are in place, release the regular brakes until the chocks absorb the load.
Page 268 NOTES 4-44...
Page 269: Service And Appearance Care
Section 5 Service ...5-3 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of Your Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-5 California Fuel ...5-5 Additives ...5-6 Fuels in Foreign Countries ...5-6 Filling Your Tank ...5-7 Filling a Portable Fuel Container ...5-10 Checking Things Under the Hood ...5-10 Hood Release ...5-11...
Page 270 Section 5 If a Tire Goes Flat ...5-76 Changing a Flat Tire ...5-77 Removing the Spare Tire and Tools ...5-78 Removing the Flat Tire and Installing the Spare Tire ...5-80 Storing a Flat or Spare Tire and Tools ...5-85 Compact Spare Tire ...5-86 Appearance Care ...5-87 Fabric/Carpet ...5-87 Vinyl ...5-89...
Page 271: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 272: Doing Your Own Service Work
Doing Your Own Service Work If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-11.
Page 273: Adding Equipment To The Outside Of Your Vehicle
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle.
Page 274: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly. In most cases, you should not have to add anything to your fuel.
Page 275: Filling Your Tank
Filling Your Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 276 The fuel door release button is located to the left of the steering wheel next to the exterior lamp control. The button only works when the vehicle is in PARK (P) or NEUTRAL (N), the key is in the ignition and the VALET lockout button is in OFF.
Page 277 Be careful not to spill fuel. Do not top off or overﬁll the tank and wait a few seconds after you have ﬁnished pumping before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See Washing Your Vehicle on page 5-91. When replacing the fuel cap, turn it to the right (clockwise) until it clicks.
Page 278: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 279: Hood Release
Hood Release To lift the hood, use the following steps: 1. Pull the lever inside the vehicle to open the hood. It is located on the lower left side of the instrument panel. Vehicle without Night Vision shown 2. Then go to the front of the vehicle and ﬁnd the secondary hood release lever.
Page 280: Engine Compartment Overview
Engine Compartment Overview When you open the hood, here is what you will see: 5-12...
Page 281 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-36. B. Underhood Fuse Block. See Underhood Fuse Block on page 5-98. C. Engine Coolant Surge Tank and Pressure Cap. See Coolant Surge Tank Pressure Cap on page 5-27 and Cooling System on page 5-30.
Page 282: Engine Oil
Engine Oil If the CHECK OIL LEVEL message appears on the instrument cluster, it means you need to check your engine oil level right away. For more information, see “CHECK OIL LEVEL” under DIC Warnings and Messages on page 3-60. You should check your engine oil level regularly;...
Page 283: When To Add Engine Oil
When to Add Engine Oil If the oil is at or below the cross-hatched area at the tip of the dipstick, then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use.
Page 284 5-16 • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container.
Page 285: Engine Oil Life System
Notice: Use only engine oil identiﬁed as meeting GM Standard GM6094M and showing the American Petroleum Institute Certiﬁed For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty. ® GM Goodwrench oil meets all the requirements for your vehicle.
Page 286: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and ﬁlter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE ENGINE OIL message in the Driver Information Center (DIC) being turned on, reset the system.
Page 287: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-12 for the location of the engine air cleaner/ﬁlter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after 50,000 miles (83 000 km).
Page 288 3. Remove the engine air cleaner/ﬁlter element and any loose debris that may be found in the air cleaner base. 4. Inspect or replace the air ﬁlter element. Follow these steps to reinstall the cover to the engine air cleaner/ﬁlter housing: 1.
Page 289: Automatic Transaxle Fluid
Automatic Transaxle Fluid When to Check and Change A good time to check your automatic transaxle ﬂuid level is when the engine oil is changed. Change both the ﬂuid and ﬁlter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one or more of these conditions: •...
Page 290 Checking the Fluid Level Prepare you vehicle as follows: • Park your vehicle on a level place. Keep the engine running. • With the parking brake applied, place the shift lever in PARK (P). • With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range.
Page 291: How To Add Fluid
3. Check both sides of the dipstick, and read the lower level. The ﬂuid level must be in the cross-hatched area. 4. If the ﬂuid level is in the acceptable range, push the dipstick back in all the way and turn the handle clockwise.
Page 292: Engine Coolant
How to Reset the Transaxle Fluid Indicator After the transaxle ﬂuid has been changed, the transaxle ﬂuid change indicator must be reset. To reset the indicator, do the following: 1. Press the INFO button on the Driver Information Center (DIC) until TRANS FLUID LIFE is displayed. 2.
Page 293: What To Use
What to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 294: Checking Coolant
Checking Coolant The engine coolant surge tank is located toward the rear of the engine compartment on the passenger’s side of the vehicle. For more information on location, see Engine Compartment Overview on page 5-12. 5-26 CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Page 295: Coolant Surge Tank Pressure Cap
Adding Coolant If you need more coolant, add the proper DEX-COOL coolant mixture at the surge tank, but only when the engine is cool. CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough.
Page 296: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 297: Overheated Engine Protection Operating Mode
If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traffic, let the engine idle in NEUTRAL (N) while stopped. If it safe to do so, pull off the road, shift to PARK (P) or NEUTRAL (N) and let the engine idle.
Page 298: Cooling System
Cooling System When you decide it is safe to lift the hood, here is what you will see: A. Coolant Surge Tank with Pressure Cap B. Electric Engine Cooling Fans 5-30 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
Page 299 CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ﬁre, and you could be burned.
Page 300: How To Add Coolant To The Coolant Surge Tank
How to Add Coolant to the Coolant Surge Tank If you have not found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible but the level is not 4.5 inches (11.4 cm) below the top of the ﬁller neck, add a 50/50 mixture of clean, drinkable water ®...
Page 301 CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning.
Page 302 1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise (left) until it ﬁrst stops. Do not press down while turning the pressure cap.
Page 303: Power Steering Fluid
4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. By this time, the coolant level inside the coolant surge tank may be lower.
Page 304: Windshield Washer Fluid
How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag.
Page 305: Brakes
Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. • Do not mix water with ready-to-use washer ﬂuid. Water can cause the solution to freeze and damage your washer ﬂuid tank and other parts of the washer system.
Page 306: What To Add
So, it is not a good idea to top off your brake ﬂuid. Adding brake ﬂuid will not correct a leak. If you add ﬂuid when your linings are worn, then you will have too much ﬂuid when you get new brake linings. You should add or remove brake ﬂuid, as necessary, only when work is done on the brake hydraulic system.
Page 307: Brake Wear
Notice: • Using the wrong ﬂuid can badly damage brake system parts. For example, just a few drops of mineral-based oil, such as engine oil, in your brake system can damage brake system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of ﬂuid.
Page 308: Battery
Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you apply the brakes, with or without the vehicle moving, your brakes adjust for wear.
Page 309 CAUTION: A battery that is not properly vented can let sulfuric acid fumes into the area under the rear seat cushion. These fumes can damage your rear seat safety belt systems. You may not be able to see this damage, and the safety belts might not provide the protection needed in a crash.
Page 310: Jump Starting
Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative ( ) cable from the battery. This will help keep your battery from running down. CAUTION: Batteries have acid that can burn you and gas that can explode.
Page 311 Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
Page 312 4. Open the hoods and locate the positive (+) and negative ( ) terminal locations on the other vehicle. Your vehicle has a remote positive (+) jump starting terminal and a remote negative ( ) jump starting terminal. The remote positive (+) terminal is located in the engine compartment on the passenger’s side of...
Page 313 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 314 6. Connect the red positive (+) cable to the remote positive (+) terminal location on the vehicle with the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal location of the vehicle with the good battery.
Page 315 Jumper Cable Removal A. Dead Battery or Remote Positive (+) Terminal B. Good Battery or Remote Positive (+) and Remote Negative ( ) Terminals C. Heavy, Unpainted Metal Engine Part or Remote Negative ( ) Terminal (GND) To disconnect the jumper cables from both vehicles, do the following: 1.
Page 316: Headlamp Aiming
Headlamp Aiming Your vehicle has a visual optical headlamp aiming system which may be equipped with horizontal aim indicators. The aim has been preset at the factory and should need no further adjustment. This is true even though your horizontal aim indicators (if equipped) may not fall exactly on the “0”...
Page 317: Headlamp Horizontal Aiming
Headlamp aiming is done with the vehicle low-beam lamps. The high-beam lamps will be correctly aimed if the low-beam lamps are aimed properly. The headlamp aiming devices are located under the hood near the headlamps. If you believe your headlamps need horizontal (left/right) adjustment, follow the horizontal aiming procedure.
Page 318: Headlamp Vertical Aiming
Headlamp Vertical Aiming Notice: Horizontal aiming must be performed before making any adjustments to the vertical aim. Adjusting the vertical aim ﬁrst will result in an incorrect headlamp aim. 1. Find the aim dot on the lens of the low-beam lamps. 2.
Page 319: Bulb Replacement
6. Turn the vertical aiming screw (C) until the headlamp beam is aimed to the horizontal tape line. The top edge of the cut-off should be positioned at the bottom edge of the horizontal tape line. 7. Repeat Steps 4 through 6 for the opposite headlamp. Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-56.
Page 320 2. Remove the two bolts at the top of the headlamp assembly. 3. Loosen the bolt at the bottom of the headlamp assembly. 5-52 4. Use a tool to help pry the headlamp assembly away from the vehicle.
Page 321 5. Firmly grasp the outboard side of the headlamp assembly with both hands and pull hard enough so that the whole assembly separates from the vehicle. 6. Remove the bulb socket dust cover. 7. Turn the headlamp housing socket counterclockwise to unlock the socket from the lamp housing.
Page 322 8. Pull the old bulb out of the socket. 9. Install the new bulb into the socket. Make sure that the bulb is locked in ﬁrmly. 10. Reinstall the headlamp housing socket into the headlamp assembly. 11. Reinstall the headlamp assembly by reversing Steps 2 through 6.
Page 323: Front Turn Signal, Sidemarker, Parking And Cornering Lamps
Front Turn Signal, Sidemarker, Parking and Cornering Lamps 1. The turn signal lamps are located beside the headlamp bulbs. To access, lift off the bulb socket dust cover. See Steps 1 through 6 under Headlamps on page 5-51. 2. Press the tab down and turn the housing socket clockwise to unlock the socket from the lamp housing.
Page 324: Replacement Bulbs
Replacement Bulbs Exterior Lamp Cornering Lamps Front Turn Signal Headlamps, Lower High-Beam Upper Low-Beam For replacement bulbs not listed here, contact your dealer. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected each time maintenance is performed. See Scheduled Maintenance on page 6-4 for more information on wiper blade inspection.
Page 325: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s owner’s manual.
Page 326: Tire Sidewall Labelling
Tire Sidewall Labelling Useful information about a tire is molded into its sidewall. Passenger Car Tire Example 5-58 (A) Tire Size: The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description.
Page 327 (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance.
Page 328 (C) Tire Identiﬁcation Number (TIN): The Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Page 329: Tire Size
(C) Dual Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used in a dual conﬁguration. (D) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards.
Page 330: Tire Terminology And Deﬁnitions
(D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches.
Page 331 GVWR: Gross Vehicle Weight Rating, see Loading Your Vehicle on page 4-30. GAWR FRT: Gross Axle Weight Rating for the front axle, see Loading Your Vehicle on page 4-30. GAWR RR: Gross Axle Weight Rating for the rear axle, see Loading Your Vehicle on page 4-30. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle.
Page 332 Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead.
Page 333: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 334: How To Check
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 335 If your vehicle has P225/60R16 97S or P235/55R17 98H size tires and you will be driving at speeds of 100 mph (160 km/h) or higher, where it is legal, set the cold inﬂation pressure to the maximum inﬂation pressure shown on the tire sidewall, or 38 psi (265 kPa), whichever is lower.
Page 336: Tire Pressure Monitor Operation
Tire Pressure Monitor Operation If your vehicle has the Tire Pressure Monitor (TPM) system, it uses radio and sensor technology to check tire pressure levels. Sensors, mounted on each road wheel, transmit tire pressure readings to a receiver located in the trunk.
Page 337: Tire Inspection And Rotation
The TPM system also allows the driver to check the air pressure status of each road tire using the Driver Information Center (DIC). Each tire’s air pressure will be listed individually, in the following order: LF (left front or driver’s side front tire), RF (right front or passenger’s side front tire), RR (right rear or passenger’s side rear tire) and LR (left rear or driver’s side rear tire).
Page 338: When It Is Time For New Tires
After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label. Vehicles equipped with the Tire Pressure Monitor (TPM) system will need to have the sensors reset after a tire rotation is performed.
Page 339: Buying New Tires
Buying New Tires To ﬁnd out what kind and size of tires your vehicle needs, look at the tire and loading information label. For more information about this label and its location on your vehicle, see Loading Your Vehicle on page 4-30. The tires installed on your vehicle when it was new had a Tire Performance Criteria Speciﬁcation (TPC Spec) number on each tire’s sidewall.
Page 340: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Page 341: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 342: Used Replacement Wheels
Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts.
Page 343: Tire Chains
Tire Chains CAUTION: If your vehicle has P235/55R17, LT235/60R17E or P235/60R17/EL size tires, do not use tire chains, there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts.
Page 344: If A Tire Goes Flat
If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire will create a drag that pulls the vehicle toward that side.
Page 345: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning ﬂashers. CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Page 346: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is in the trunk. The instructions for changing a tire is on the inside of the tire cover located in your trunk. To gain access to the instructions, spare tire and jacking equipment, do the following: 1.
Page 347 3. Turn the wing nuts to remove the container that holds the wrench and jack. 4. Remove the wheel wrench, jack and compact spare tire from the trunk. See Compact Spare Tire on page 5-86 for more information. The tools you will be using include the jack (A) and the wheel wrench (B).
Page 348: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire Models with Center Wheel Cover 1. For models having aluminum wheels with a center wheel cover, use the ﬂat end of the wheel wrench to gently pry the wheel covers off. Be careful not to scratch the aluminum wheel edge and do not try to remove it with your hands.
Page 349 3. Find the jacking location from the diagram above and corresponding hoisting notches located in the plastic molding. The front location is (A) 8.5 inches (21 cm) from the rear edge of the front wheel well, and the rear location (B) is 3.5 inches (8.5 cm) from the front edge of the rear wheel well.
Page 350 5. Raise the jack until the metal ﬂange ﬁts ﬁrmly into the channel of the jack head. 6. Put the compact spare tire near you. 5-82 7. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground for the compact spare tire to ﬁt under the vehicle.
Page 351 CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle.
Page 352 12. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely. 5-84 CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident.
Page 353: Storing A Flat Or Spare Tire And Tools
5-Wheel Nuts 13. Tighten the wheel nuts ﬁrmly in a crisscross sequence as shown. If your vehicle is equipped with wheel nut covers, screw them on with your ﬁngers, then tighten one-quarter turn with the wheel wrench. Notice: Wheel covers will not ﬁt on your compact spare.
Page 354: Compact Spare Tire
A. Wrench D. Retainer B. Jack E. Compact Spare C. Jack Container Tire Cover Compact Spare Tire Although the compact spare tire was fully inﬂated when the vehicle was new, it can lose air after a time. Check the inﬂation pressure regularly. It should be 60 psi (420 kPa).
Page 355: Appearance Care
Appearance Care Cleaning products can be hazardous. Some are toxic. Other cleaning products can burst into ﬂames if a match is struck near them or if they get on a hot part of the vehicle. Some are dangerous if their fumes are inhaled in a closed space.
Page 356: Special Fabric Cleaning Problems
Most stains can be removed with club soda water. To clean, use the following instructions: 1. For liquids: blot with a clean, soft, white cloth. For solids: remove as much as possible and then vacuum or brush. 2. Apply club soda water to a clean, soft, white cloth. Do not over-saturate;...
Page 357: Vinyl
Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. This may have to be done more than once. • Things like tar, asphalt, and shoe polish will stain if they are not removed quickly. Use a clean cloth and vinyl cleaner.
Page 358: Speaker Covers
Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap. Glass Surfaces Glass should be cleaned often. GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust ﬁlms on interior glass.
Page 359: Washing Your Vehicle
Washing Your Vehicle The paint ﬁnish on the vehicle provides beauty, depth of color, gloss retention, and durability. The best way to preserve the vehicle’s ﬁnish is to keep it clean by washing it often with lukewarm or cold water. Do not wash the vehicle in the direct rays of the sun.
Page 360: Finish Care
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint ﬁnish. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 5-95. The vehicle has a “basecoat/clearcoat” paint ﬁnish. The clearcoat gives more depth and gloss to the colored basecoat.
Page 361: Aluminum Or Chrome-Plated Wheels
Aluminum or Chrome-Plated Wheels The vehicle may be equipped with either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
Page 362: Tires
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Page 363: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products. Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Oil Removes tar, road oil, Remover and asphalt. Chrome Cleaner and Use on chrome or Polish stainless steel.
Page 364: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 365: Electrical System
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 366: Fuses And Circuit Breakers
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of ﬁres caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.
Page 367 Fuses Usage Assembly Line Diagnostic Work Accessory Windshield Wipers Not Used Headlamp Low Beam Left Headlamp Low Beam Right Instrument Panel Powertrain Control Module Battery Headlamp High Beam Right Fuses Usage Headlamp High Beam Left Ignition 1 Fog Lamps (Option) Transmission Cruise Control Coil Module (Option)
Page 368 Fuses Anti-Lock Brake System Air Pump Cooling Fan 1 Cooling Fan 2 Spare Spare Spare Spare Spare Heated Steering Wheel (Option) Relays Headlamp High Beam Headlamp Low Beam Fog Lamps (Option) Daytime Running Lamps 5-100 Usage Relays Usage Circuit Breakers Miscellaneous Usage Horn...
Page 369: Rear Underseat Fuse Block
Rear Underseat Fuse Block The rear fuse block is located under the rear seat on the driver’s side. The rear seat cushion must be removed to access the rear fuse block. Removing the Rear Seat Cushion Notice: If you touch the exposed wires with the metal on the seat cushion, you could cause a short that could damage the battery and or wires.
Page 370 To reinstall the rear seat cushion, do the following: CAUTION: A safety belt that is not properly routed through the seat cushion or is twisted will not provide the protection needed in a crash. CAUTION: (Continued) 5-102 CAUTION: (Continued) If the safety belt has not been routed through the seat cushion at all, it will not be there to work for the next passenger.
Page 371 Fuses Usage Fuel Pump Heater, Ventilation and Air Conditioning Battery Memory Seat, Tilt and Telescoping Steering RR Lumbar, Antenna Driver Door Module Heated Seat Left Rear Power Tilt and Telescoping Steering Fuses Usage Supplemental Inﬂation Restraint SDAR (XM™ Satellite Radio) Lamps Park Right Fuel Tank Ventilation Solenoid Ignition 1...
Page 372 Fuses Passenger Door Module Body Export Lights, Power Locks Rear HVAC Blower Ignition Switch Turn Signal, Hazard Signal Reverse, Locks Continuous Variable Road Sensing Suspension Heating, Ventilation, Air Conditioning Ignition 3 Rear Antilock Braking System Heated Seat, Right Front Heated Seat, Right Rear Dimmer Not Used 5-104...
Page 373 Relays Usage Fuel Pump Parking Lamps Ignition 1 Not Used Not Used Park Shift Interlock Reverse Lamps Retained Accessory Power for Sunroof Reverse Lockout Suspension Dampers Ignition 3 Fuel Tank Door Release Interior Lamps Relays Trunk Release Not Used Lock, Cylinder Automatic Level Control Compressor Not Used Rear Defog...
Page 374: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant R134a Cooling System Engine Oil with Filter Fuel Tank Transaxle Wheel Nut Torque All capacities are approximate.
Page 375 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using Your Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-9 At Each Fuel Fill ...6-9 At Least Once a Month ...6-9 At Least Once a Year ...6-10 Recommended Fluids and Lubricants ...6-12...
Page 376: Introduction
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended ﬂuids and...
Page 377 This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will ﬁnd these limits on the tire and loading information label. See Loading Your Vehicle on page 4-30. • are driven on reasonable road surfaces within legal driving limits.
Page 378: Scheduled Maintenance
Scheduled Maintenance When the CHANGE ENGINE OIL message in the Driver Information Center (DIC) comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 379 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter.See Engine Oil on page 5-14. Reset oil life system. See Engine Oil Life System on page 5-17. An Emission Control Service. Visually check for any leaks or damage. See footnote (k). Inspect engine air cleaner ﬁlter.
Page 380: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 381: Maintenance Footnotes
Service and Miles (Kilometers) Professional Vehicle Only: Engine cooling system service (or every 5 years, whichever occurs ﬁrst). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to...
Page 382 (e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 383: Owner Checks And Services
Owner Checks and Services These owner checks and services should be performed at the intervals speciﬁed to help ensure the safety, dependability and emission control performance of your vehicle. Your GM Goodwrench dealer can assist you with these checks and services. Be sure any necessary repairs are completed at once.
Page 384: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle.
Page 385: Ignition Transaxle Lock Check
Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition to OFF in each shift lever position. • The ignition should turn to OFF only when the shift lever is in PARK (P). •...
Page 386: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines starburst symbol.
Page 387: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer. Part Engine Air Cleaner/Filter Element Engine Oil Filter Passenger Compartment Air Filter Element Spark Plugs Wiper Blade (Shepherd’s Hook Type) 22 inches (56.5 cm) ®...
Page 388: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. Also, you should retain all maintenance receipts.
Page 389 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-15...
Page 390 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 391: Customer Assistance And Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-3 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Reimbursement Program ...7-5 Roadside Service ...7-5 Courtesy Transportation ...7-7 Vehicle Data Collection and Event Data Recorders ...7-9 Customer Assistance and Information Reporting Safety Defects ...7-10...
Page 392: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Cadillac. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 393: Online Owner Center
The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to ﬁling a court action, use of the program is free of charge and your case will generally be heard within 40 days.
Page 394: Customer Assistance For Text Telephone (Tty) Users
Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Cadillac has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Cadillac by dialing: 1-800-833-CMCC (2622). (TTY users in Canada can dial 1-800-263-3830.)
Page 395: Gm Mobility Reimbursement Program
1-800-882-1112, 24 hours a day, 365 days a year. This service is provided at no charge for any warranty-covered situation and for a nominal charge if the Cadillac is no longer under warranty. Roadside Service is available only in the United States and Canada.
Page 396: Cadillac Owner Privileges
A dealer technician, if available, can travel to your location within a 30 mile (50 km) radius of a participating Cadillac dealership. If beyond this radius, we will arrange to have your car towed to the nearest Cadillac dealership.
Page 397: Courtesy Transportation
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Cadillac helps minimize your inconvenience by providing several transportation options. Depending on the circumstances,...
Page 398: Additional Program Information
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for a warranty repair. Reimbursement will be limited to a maximum of $40 a day and must be supported by receipts.
Page 399: Vehicle Data Collection And Event Data Recorders
Vehicle Data Collection and Event Data Recorders Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the vehicle in difficult driving situations.
Page 400: Reporting Safety Defects
In addition, once GM collects or receives data, GM may: • use the data for GM research needs, • make it available for research where appropriate conﬁdentiality is to be maintained and need is shown, or • share summary data which is not tied to a speciﬁc vehicle with non-GM organizations for research purposes.
Page 401: Reporting Safety Defects To The Canadian Government
Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169 In Canada, please call us at 1– 888– 446–2000. Or, write: Canadian Cadillac Customer Communication Centre, 163-005 General Motors of Canada Limited 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7...
Page 402: Current And Past Model Order Forms
Owner’s Information Owner publications are written speciﬁcally for owners and intended to provide basic operational information about the vehicle. The owner’s manual will include the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner’s Manual, and Warranty Booklet. RETAIL SELL PRICE: $35.00 Without Portfolio: Owner’s Manual only.
Page 403 Accessory Power Outlets ... 3-28 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-97 Air Cleaner/Filter, Engine ... 5-19 Air Conditioning ... 3-30 Airbag Readiness Light ... 3-45 Airbag Sensing and Diagnostic Module (SDM) ... 7-9 Airbag System ... 1-45 How Does an Airbag Restrain? ...
Page 404 Audio System(s) (cont.) Setting the Time for Radios with Radio Data Systems (RDS) ... 3-80 Setting the Time for Radios without Radio Data Systems (RDS) ... 3-80 Theft-Deterrent Feature ... 3-103 Understanding Radio Reception ... 3-104 XM™ Satellite Radio Antenna System ... 3-107 Automatic Transaxle Fluid ...
Page 405 Check Engine Light ... 3-50 Checking Things Under the Hood ... 5-10 Chemical Paint Spotting ... 5-94 Child Restraints Child Restraint Systems ... 1-31 Infants and Young Children ... 1-28 Lower Anchorages and Top Tethers for Children (LATCH System) ... 1-37 Older Children ...
Page 406 Cooling System ... 5-30 Cornering Lamps ... 3-18 Courtesy Lamps ... 3-21 Cruise Control Lever ... 3-12 Cruise Control Light ... 3-54 Customer Assistance Information Courtesy Transportation ... 7-7 Customer Assistance for Text Telephone (TTY) Users ... 7-4 Customer Assistance Offices ... 7-4 Customer Satisfaction Procedure ...
Page 407 Electrical System Add-On Equipment ... 5-97 Fuses and Circuit Breakers ... 5-98 Headlamp Wiring ... 5-97 Power Windows and Other Power Options ... 5-97 Rear Underseat Fuse Block ... 5-101 Underhood Fuse Block ... 5-98 Windshield Wiper Fuses ... 5-97 Engine Air Cleaner/Filter ...
Page 408 Fuses Fuses and Circuit Breakers ... 5-98 Rear Underseat Fuse Block ... 5-101 Underhood Fuse Block ... 5-98 Windshield Wiper ... 5-97 Gage Engine Coolant Temperature ... 3-49 Fuel ... 3-55 Speedometer ... 3-43 Tachometer ... 3-44 Garage Door Opener ... 2-44 Gasoline Octane ...
Page 409 Ignition Positions ... 2-24 Inadvertent Power Battery Saver ... 3-23 Infants and Young Children, Restraints ... 1-28 Inﬂation -- Tire Pressure ... 5-65 Instrument Panel Brightness ... 3-20 Cluster ... 3-41 Overview ... 3-4 Storage Area ... 2-48 Jump Starting ... 5-42 Keyless Entry System ...
Page 410 Lighting Entry ... 3-21 Parade Dimming ... 3-21 Lockout Protection ... 2-11 Locks Central Door Unlocking System ... 2-9 Door ... 2-8 Lockout Protection ... 2-11 Power Door ... 2-9 Programmable Automatic Door Locks ... 2-10 Rear Door Security Locks ... 2-10 Loss of Control ...
Page 411 Navigation/Radio System ... 3-99 New Vehicle Break-In ... 2-24 Night Vision System ... 3-23 Normal Maintenance Replacement Parts ... 6-13 Odometer ... 3-43 Odometer, Trip ... 3-43 Off-Road Recovery ... 4-12 Engine ... 5-14 Life Indicator ... 3-79 Pressure Light ... 3-53 Older Children, Restraints ...
Page 412 Power (cont.) Lumbar Controls ... 1-2 Rear Lumbar Controls ... 1-6 Retained Accessory (RAP) ... 2-25 Seat ... 1-2 Steering Fluid ... 5-35 Tilt Wheel and Telescopic Steering Column ... 3-7 Windows ... 2-16 Pretensioners, Safety Belt ... 1-25 Programmable Automatic Door Locks ... 2-10 ®...
Page 413 Reporting Safety Defects Canadian Government ... 7-11 General Motors ... 7-11 United States Government ... 7-10 Restraint System Check Checking Your Restraint Systems ... 1-54 Replacing Restraint System Parts After a Crash ... 1-55 Restraint Systems Checking ... 1-54 Replacing Parts ... 1-55 Retained Accessory Power (RAP) ...
Page 414 Service (cont.) Engine Soon Light ... 3-50 Publications Ordering Information ... 7-11 Servicing Your Airbag-Equipped Vehicle ... 1-54 Setting the Time Radios with Radio Data Systems (RDS) ... 3-80 Radios without Radio Data Systems (RDS) ... 3-80 Sheet Metal Damage ... 5-94 Shifting Into Park (P) ...
Page 415 Tires (cont.) Changing a Flat Tire ... 5-77 Cleaning ... 5-94 Compact Spare Tire ... 5-86 If a Tire Goes Flat ... 5-76 Inﬂation -- Tire Pressure ... 5-65 Inspection and Rotation ... 5-69 Installing the Spare Tire ... 5-80 Pressure Monitor Operation ...
Page 416 Vehicle Identiﬁcation Number (VIN) ... 5-96 Service Parts Identiﬁcation Label ... 5-96 Vehicle Personalization DIC ... 3-68 Memory Seat, Mirrors and Steering Wheel ... 2-52 Ventilation Adjustment ... 3-34 Visors ... 2-18 Warning Lights, Gages and Indicators ... 3-40 Warnings DIC Warnings and Messages ...

Cadillac 2005 DeVille Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Homelink Transmitter

Storage Areas

Sunroof

Vehicle Personalization

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Trip Computer

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Cadillac 2005 DeVille

Summary of Contents for Cadillac 2005 DeVille