OttLite 25D54BZX Quick Start Manual

G
H
J
K
L
2 shades – Mica and Linen –
Both Included
Incluye 2 pantallas (mica y lino)
2 abat-jours – 1 couleur lin et 1
couleur mica – sont inclus
25w Coupelle Floor Lamp
25D54BZX
9602
REV081511
ENGLISH
CONGRATULATIONS! You've
purchased the finest in natural lighting
technology with your new OttLite
product.
PRODUCT REGISTRATION FORM
F
Please complete the enclosed Product
Registration Form and return it today
by mail, or register online by going to:
http://OttLite.com/warranty
WARNING: To prevent electric shock,
make sure the lamp is not plugged in
until all assembly steps are complete.
To avoid lamp tip over, position lamp
shade as shown in diagram.
LAMP ASSEMBLY
1. Make sure the lamp is not plugged
E
into an electrical socket.
2. If the lamp has been in use, allow it to
cool approximately five minutes before
proceeding.
3. Remove lamp from packing placing
D the base (B) flat on a steady surface.
4. Thread upper pole (E) to arm (F)
turning clockwise by hand until tight.
5. Thread middle pole (D) to upper pole
(E) turning clockwise by hand until tight.
C
6. Thread bottom pole (C) to middle pole
(D) turning clockwise by hand until tight.
B 7. Thread base (B) to bottom pole (C)
A
by hand carefully turning clockwise until
tight. Keep poles inline with base (B) to
prevent crossthreading. Excess cord may
be pulled through the base (B).
8. Fit shade (J) over socket (H) then
thread socket ring (K) onto socket. Turn
socket ring (K) clockwise to tighten until
finger tight and the shade (J) is held
securely.
9. Refer to BULB INSTALLATION AND
REMOVAL to install bulb (L) in lamp.
CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
Coupelle Floor Lamp
10. Plug the cord into a standard 120Vac
outlet.
®
11. To turn the lamp on or off depress
cord mounted footswitch (A).
12. To postion the shade (J), loosen
thumbscrew (G), move shade (J) into
position, then tighten thumbscrew (G) by
hand until snug.
DO NOT force thumbscrew as damage to
the lamp may occur.
BULB INSERTION/REMOVAL
1. Make sure the lamp is not plugged into
an electrical socket.
2. If the lamp has been in use, allow it to
cool approximately 5 minutes before
proceeding.
3. To install the bulb (L) in the socket
(H), thread the base of the bulb into the
socket turning clockwise until snug.
CAUTION: DO NOT overtighten the
bulb. Overtightening the bulb may
make removal difficult or damage the
lamp or bulb.
4. To remove a bulb (L) already installed
in the lamp, unthread the bulb from the
socket (H) turning counterclockwise to
loosen.
Please note that in operation, OttLite
®
bulbs are not dimmable.
Enjoy your OttLite Coupelle Floor Lamp!
®
This lighting system is designed
for use with OttLite® type bulbs
(Style Number ED25-V). Use of other
products voids the warranty and
may result in damage to the lighting
system.
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF
THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED.
DO NOT ALTER THE PLUG.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
¡ PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
IMPORTANTES:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES MÁS ANCHA QUE LA
OTRA) COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE
ENCAJARÁ EN CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE NO CALZA
COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CONTACTO
CON UN ELECTRICISTA CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA
SER TOTALMENTE INSERTADO. NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA
ANCHA DEL ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
AVERTISSEMENT! IMPORTANTES DIRECTIVES
DE SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE L'AUTRE). CE
DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S'INSÈRE
DANS LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE
N'ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE
SAUF SI LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA
FICHE DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.