Sony SRS-D511 Operating Instructions

2-593-589-11(1)
Active Speaker System
Operating Instructions
Mode d'emploi
Manual de instrucciones
SRS-D511
 2005 Sony Corporation
Printed in Malaysia
Owner's Record
The model number and the serial number are located on the rear of the subwoofer.
Record the model number and the serial number in the space provided below.
Refer to them whenever you call upon your Sony dealer regarding this product.
Printed on 100 % recycled paper using
Model No. SRS-D511
Serial No. VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Package Contents
Subwoofer with wired controller (1)
Satellite speaker
with 2-meter cord (2) Connecting Cable (for 5.1
with 3-meter cord (3) Stand (5) channel signal input) (1)
A
A
,
Reverse the stand to
change the speaker
Satellite speaker
Stand
angle.
B
Anchor hole
Hollow wall anchor
(ø 4 mm, not supplied)
,
Note
5 mm
Do not hang anything on the
Note
satellite speaker.
First, be sure to apply a bond
(anaerobic threadlocking material) ø 7 mm
to the hollow wall anchor to
prevent the screw loosening.
ø 4 mm
9.5 mm or more
B
Satellite speaker (rear)
to LINE OUT or
to CENTER
headphones jack
jack
(stereo mini-jack)
(3 meters)
to FRONT R jack
to FRONT L jack
CD/MD Walkman*, etc.
(2 meters) (2 meters)
Connecting cord
to REAR R jack to REAR L jack
(not supplied)
(3 meters)
to INPUT 2 (3 meters)
Connecting Cable
jack
(for 5.1 channel signal input)
(supplied)
Controller (rear)
Subwoofer (rear)
to INPUT 1 jack
(Green to front,
to wall outlet
Line out of sound card Orange to center,
or sound box. and Black to rear channel)
* "WALKMAN" is a registered
to LINE OUT jack (Green to
trademark of Sony Corporation to
front, Orange to center, and
represent Headphone Stereo products.
Black to rear channel)
C
Center speaker
PC, CD or MD
Walkman, etc.
POWER ON
OFF
MIN MAX
MIN MAX
MIN MAX
MIN MAX
PHONES
Rear speaker Rear speaker
(Left) (Right)
Subwoofer
Front speaker (Left)
Controller
Front speaker (Right)
D
POWER
ON
POWER
DUAL STEREO
ON DUAL STEREO
OFF
OFF
VOLUME INPUT 2
MIN MAX
BASS INPUT 1
MIN MAX FRONT
VOLUME
REAR
REAR
MIN MAX
CENTER
CENTER
MIN MAX SUBWOOFER
PHONES
PHONES
Controller (Front) Controller (Rear)
VOLUME: Controls total volume level. DUAL STEREO: Switches a 4 channel or 2 channel
BASS: Adjusts bass level (Subwoofer). source to 5.1 channel.
REAR: Adjusts rear surround sound (Rear Speaker). Set the switch to ON when a 4-channel or 2-channel
CENTER: Adjusts center speaker level as necessary to source is output from a PC, Walkman, etc., connected
make balanced sound. to this system. The front and rear speakers will
PHONES: Connect the headphones for personal output the front channel of these sources. The center
listening. speaker will output the mixed left and right front
In this case, only the FRONT L/R channel signals channels of these sources. In this case, the subwoofer,
will be useful. The CENTER channel is not activated. center and rear speakers will not operate with a 5.1-
You cannot use the BASS, REAR or CENTER volume channel source.
dial. Set the switch to OFF when a 5.1-channel source is
output from a PC or sound card connected to this
system. 5.1-channel surround sound will output. In
this case, the subwoofer, rear and center speakers
will not operate with a 2-channel source, and the
center speaker and subwoofer will not operate with a
4-channel source. For details about the sound card
setting, refer to the operating instructions of the
sound card.
This system needs either a sound card (5.1 • The unit is not disconnected from the AC power
channel) for PC or a decoder box. They are source (mains) as long as it is connected to the wall
not supplied with this system. outlet, even if the unit itself has been turned off.
• Unplug the system from the wall outlet if it is not to
be used for an extended period of time. To disconnect
the cord, pull the cord by grasping the plug. Never
English
pull the cord itself.
• Should any liquid or solid object fall into the system,
Before operating the unit, please read this manual unplug the system's power cord and have the system
thoroughly and retain it for future reference. checked by qualified personnel before operating it
any further.
• The AC power cord should be changed only at a
WARNING
qualified service shop.
To prevent fire or shock hazard, do not expose the • For efficient heat dissipation, ensure there is sufficient
unit to rain or moisture. space to the rear of the subwoofer. Also, avoid
To avoid electrical shock, do not open the cabinet. Refer placing objects on the unit.
servicing to qualified personnel only. • Do not insert your hand or any objects into the hole of
To prevent fire, do not cover the ventilation of the the subwoofer.
apparatus with news papers, table-cloths, curtains, etc.
Do not place lighted candles on the apparatus. On operation
To prevent fire or shock hazard, do not place objects • Do not drive the speaker system with a continuous
filled with liquids, such as vases, on the apparatus.
wattage exceeding the maximum input power of the
system.
Do not install the appliance in a confined space,
• Before connecting, turn off the speaker system, the
such as a bookcase or built-in cabinet.
PC and audio component to avoid damaging the
speaker system.
CAUTION
• The volume level should not be turned up to the
You are cautioned that any changes or modification not
point of distortion.
expressly approved in this manual could void your
• Although this system is magnetically shielded, do not
authority to operate this equipment.
leave recorded tapes, watches, personal credit cards
or floppy disks using magnetic coding in front of the
NOTICE FOR THE CUSTOMERS IN THE USA
system for an extended period of time.
If the TV picture or monitor display is
magnetically distorted
Although this system is magnetically shielded, there may
be cases that the picture on some TV sets/personal
computers may become magnetically distorted. In such a
case, turn off the power of the TV set/personal computer
once, and after 15 to 30 minutes turn it on again. In the
case of a personal computer, take appropriate measures,
such as data storage, before turning it off.
When there seems to be no improvement, locate the
This symbol is intended to alert the user to
system farther away from the TV set/personal
the presence of uninsulated "dangerous
computer. Furthermore, be sure not to place objects in
voltage" within the product's enclosure
which magnets are attached or used near the TV set/
that may be of sufficient magnitude to
personal computer, such as audio racks, TV stands, toys
constitute a risk of electric shock to persons.
etc. These may cause magnetic distortion to the picture
This symbol is intended to alert the user to due to their interaction with the system.
the presence of important operating and
maintenance (servicing) instructions in the On placement
literature accompanying the appliance.
• Do not set the speakers in an inclined position.
• Do not leave the system in a location near heat
sources, or in a place subject to direct sunlight,
Precautions
excessive dust, moisture, rain or mechanical shock.
• Do not install the satellite speaker anywhere other
than on a wall.
On safety
• Do not hang anything on the satellite speaker.
The nameplate indicating operating voltage, power
consumption, etc., is located on the rear exterior.
On cleaning
• Before operating the system, be sure that the
Do not use alcohol, benzene, or thinner to clean the
operating voltage of the system is identical with that
cabinet.
of your local power supply.
Where purchased Operating voltage
If you have any questions or problems concerning your
U.S.A./Canada 120 V AC, 60 Hz speaker system, please consult your nearest Sony
dealer.
European countries 220 – 230 V AC, 50 Hz
Other countries • 120 V AC, 60 Hz
• 220 – 230 V AC, 50 Hz
Installing the satellite speakers Using the headphones/
(See fig. A) earphones
The satellite speaker can be used either placed on a desk Connect the headphones/earphones to the PHONES
or attached to a wall. jack on the controller.
Notes
When you use the satellite speaker on a desk
• Turn off the MEGA BASS or BASS BOOST
(See fig. A-A)
(Walkman, etc.) function as it may cause audible
By attaching the stand to the satellite speaker, it can be distortion.
placed on a desk. • Only the FRONT L/R channel signals will be useful.
You cannot use the BASS, REAR or CENTER volume
1
Slide the stand into the slot at the dial.
bottom of the satellite speaker.
The stand allows you to adjust the satellite
speaker to the desired angle. Troubleshooting
2
Ensure the stands are locked. Should you encounter a problem with your speaker
Push the stand into the slot until a "click" sound is system, check the following list and take the indicated
measures. If the problem persists, consult your nearest
heard.
Sony dealer.
Note
Do not put your finger into the slot of the satellite There is no sound from the speaker system.
speaker when you lock the stand. It may cause an • Make sure all the connections have been correctly
injury to your finger. made.
• Make sure the VOLUME dial and the each speaker's
volume dial (BASS, REAR, CENTER) on the
controller have been turned up properly.
• Make sure the connected component has been turned
up properly.
• Check if the headphones are connected. If they are,
disconnect them.
The sound is distorted.
• Turn down the volume level on the connected
component. Or, if the connected component has a
BASS BOOST function, set it to off.
• Rotate BASS on this unit to reduce the bass volume.
• Turn VOLUME on this unit down to reduce the
When you use the satellite speaker attached
to a wall (See fig. A-B) volume.
There is hum or noise in the speaker output.
The satellite speaker can be attached to a wall. Follow
the Notes (below) to install safely. Improper installation • Make sure all the connections have been correctly
may result in the speaker falling and causing bodily made.
injury or damage to the speaker or other object.
• Make sure none of the audio components are
positioned too close to the TV set.
1
Secure the hollow wall anchor in the wall
The sound has suddenly stopped.
— refer to the illustration.
Make sure all the connections have been correctly
Notes made.
• Confirm wall thickness is sufficient. A The brightness of the POWER indicator is
minimum thickness of 9.5 mm is recommended unstable.
for plasterboard.
The brightness of the POWER indicator may become
• Use the specified clamp (hollow wall anchor,
unstable when the volume is turned up. This is not a
not supplied) when attaching to plasterboard. malfunction.
• Refer to the supplied operating instructions
using a hollow wall anchor.
• Use wall anchors of at least 20 kg hanging
Specifications
capacity.
• Refer to the instruction supplied with hollow
Speaker section
wall anchor.
• Requires ø 4 mm hollow wall anchor. Satellite speaker
• Set up the head of a hollow wall anchor 5 mm Speaker system Full range, magnetically shielded
from the wall. Speaker units 5.7 cm, cone type
Enclosure type Closed type
• Apply a bond (anaerobic threadlocking
Impedance 4 Ω
material) to the hollow wall anchor to prevent
Cord length 2 m (for front L and front R speakers)
the screw loosening.
3 m (for rear L, rear R and center
speakers)
2
Attach the satellite speaker to the wall.
Subwoofer
Insert the wall anchor in the anchor hole of the
Speaker system Woofer
satellite speaker.
Speaker units 12 cm, cone type
Enclosure type Bass reflex
Notes
Impedance 8 Ω
• Detach the stand from the satellite speaker
before attaching to the wall.
Amplifier section
• Ensure that the satellite speaker is securely
Rated output 5 W (10% T.H.D., 1 kHz, 4 Ω)
attached to the wall before use.
(Satellite speaker)
25 W (10% T.H.D., 100 Hz, 8 Ω)
(Subwoofer)
Input Stereo mini jack × 3 (INPUT 1 for 5.1
channel signal input)
Hooking up the system
Stereo mini jack × 1 (INPUT 2 for 2
channel signal input)
(See fig. B)
Input impedance 4.7 kΩ (at 1 kHz)
Output Stereo mini jack × 1 (PHONES)
1
Connect the satellite speakers to the
General
subwoofer. Dimensions (w/h/d) Approx. 50 × 178 × 99 mm
(2 × 7 1 / × 4 in.) (Controller)
Confirm the location and the cord length of the 8
satellite speakers. Connect the satellite speakers Approx. 98 × 124 × 84 mm
(3 / 7 × 5 × 3 3 / in.) (Satellite speaker,
with 2-meter cord to FRONT L and FRONT R jack. 8 8
on a desk)
Connect the satellite speakers with 3-meter cord to
Approx. 98 × 98 × 83 mm
REAR L, REAR R and CENTER jack.
(3 7 / × 3 / 7 × 3 3 / in.) (Satellite
8 8 8
speaker, attached to a wall)
2
Connect the controller to the source
Approx. 163 × 267 × 301 mm
equipment. (6 / 1 × 10 5 / × 11 7 / in.) (Subwoofer)
2 8 8
Mass Approx. 199 g (7 oz.) (Controller)
– Line out of sound card or sound box:
Approx. 294 g (10 oz.)
Connect the INPUT 1 jacks (FRONT, REAR, and (Satellite speaker)
CENTER/SUBWOOFER) of the controller and the Approx. 4.8 kg (10 lb. 9 oz.)
jacks of the sound card with the supplied
(Subwoofer)
connecting cable. For details, refer to the operating Cord length 2 m (Controller to subwoofer)
instructions of the sound card. 2 m (Power cord)
Power consumptions 34 W
– CD/MD Walkman, etc.:
Connect the INPUT 2 jack of the controller and the
Supplied accessories
LINE OUT or headphones jack of a CD/MD
Walkman, etc. The connecting cord is not supplied Connecting Cable (for 5.1 channel signal input)
with this system.
Note
Optional accessories
Turn on either of the connected equipment to
Connecting cord RK-G136, RK-G138
listen to its sound.
Plug adaptor PC-236MS
3
Connect the subwoofer to the wall Design and specifications are subject to change without
outlet. notice.
4 Position the speakers. (See fig. C)
Listening to the sound
(See fig. D)
First, turn down the volume on the controller. The
volume should be set to minimum before you begin
playing the programme source.
1
Set the POWER switch to ON on the
controller.
The POWER indicator lights up.
2
Turn on the desired equipment
connected to the controller.
Note
Do not turn on both connected equipments as it
may cause double sound.
3
Adjust the VOLUME control on the
controller.
You can adjust the volume of the subwoofer and
each satellite speaker.
When connecting to the headphone output, also
adjust the volume of the connected component.
After listening, set the POWER switch to OFF.
The POWER indicator goes off.
This warranty is valid only in the United States.