Advertisement
Quick Links
Advertisement
Related Manuals for Steeper Myo Kinisi
Summary of Contents for Steeper Myo Kinisi
- Page 1 Myo Kinisi Technical Manual...
-
Page 2: Table Of Contents
Programmed using the Steeper Configuration Device, which Mechanical Safety Release 15 - 16 Disposal enables the choice between Mode 0-4 for the Myo Kinisi (see the Steeper Configuration Device - Programming Guide for Myo Symbols Used on Product & Packaging 30 - 31 Maximum Pulses Kinisi). - Page 3 The Myo Kinisi is supplied in Mode 1: ‘Dual Elec’ the parameters of this mode can be adjusted using the upper limb absence. It is suitable for patients at strength.
-
Page 4: Important Clinician Information
Do not use solvents. • The Myo Kinisi is not dirt resistant or Warning: Do not modify this equipment. • Do not expose the Myo Kinisi to a naked flame waterproof, therefore moisture and/or debris Steeper Myo Kinisi Technical Manual... -
Page 5: Important User Information
Important User Information • Before detaching the Myo Kinisi from the prosthesis, you must ensure that the Myo Kinisi is switched off, press and hold the function button; as described in ‘Location of the Function Button’ (p.12) and then check the hand functionality to ensure it is switched off. -
Page 6: Technical Information
Weight of device with EQD Wrist 530g 550g 565g and hand shell Maximum 80% relative humidity, non-condensing Grip force +80N +80N +80N Do not expose to EM emissions above 8kV contact, 15kV air *All figures are for guidance only. Steeper Myo Kinisi Technical Manual... -
Page 7: Specific Activity Use 13 Returns
The Myo Kinisi is on by default after connecting to a power source; initial start up of the device will take between 2-4 seconds after If the Myo Kinisi has been fitted with a Quick Disconnect Wrist, the device must be consciously positioned when which you can operate the device. -
Page 8: Mechanical Safety Release
When force increases to elicit 1 pulse. Auto-grip is now power to the Myo Kinisi, the safety release button can be used to gripping an object, this feature will offer a grip engaged; ensuring the grip strength applied to disengage the thumb. - Page 9 If the battery fully discharges during use, as a final mode selection based on the been reset correctly. action, the Myo Kinisi will open and remain in an open need of the user. These modes position until the battery is recharged or changed.
- Page 10 Adjustable Parameters Table Myo Kinisi Mode Overview The adjustment parameters available for use with each of the five Myo Kinisi hand modes are illustrated in the Mode 0: ‘AUTO CLOSE’ Default settings are: table below: Single Site: Auto Close •...
- Page 11 For more information about the mode options for the the ‘maximum pulse count’. This is set to 3 pulses by Mode 4: ‘PULSE’ Myo Kinisi please refer to the Steeper Configuration default. Single Site: 2 Channel Signal Device Programming Guide, which can be found at: www.steepergroup.com.
- Page 12 (230 F) for 90 seconds. • Some gentle external heating of the inner hand contact the Steeper Customer Services team, or your shell can aid the process, however extreme • When the hand shell is warm and malleable; local distributor.
- Page 13 The suggested method to remove the cosmetic outer glove is to slightly open the hand and isolate the The Elegance Plus glove is designed to be used with the Myo Kinisi, however, a number of alternative gloves may power supply.
- Page 14 Serial N section on the form. notice. The service life of the Myo Kinisi is five years. Outside of this, please contact your local Steeper representaive for possibilities regarding service or repair. Location of serial Number...
-
Page 15: Disposal
IEC 60601-1-11:2015 designated collection points. Steeper is registered with both the Medicines and Healthcare This device is UKCA marked to confirm the device is IEC 60601-1-2:2014 Regulatory Authority in the UK, and the Food and Drugs... - Page 16 Packaging is covered by the Forest Stewardship Council assurance that it is made with, ISO 15223- 1:2016 Reference FSC Certification Indicates the manufacturer’s batch code so that the batch or lot can be identified. or contains, forest-based materials from FSC-certified forests or reclaimed sources. no. 5.1.5. (ISO 7000-2492) Steeper Myo Kinisi Technical Manual...
- Page 17 Prinsessegracht 20, PTY LTD (OAPL), 26-32 Clayton Centre Building 7934 King Abdul 2514 AP The Hague, Road, Clayton, VIC, 3168, Aziz Road, Al Rabi, 13315 Riyadh, Netherlands Australia. Saudi Arabia STPPR089 Issue 1 June 2021 ©2021 Steeper Group. All rights reserved.
Need help?
Do you have a question about the Myo Kinisi and is the answer not in the manual?
Questions and answers