Download
Share
Print this page
Ortur Laser Master 2 User Manual
  1. Manuals
  2. Brands
  3. Ortur Manuals
  4. Engraver
  5. Laser Master 2
  6. User manual

Ortur Laser Master 2 User Manual

Laser engraver
Hide thumbs Also See for Laser Master 2:

Advertisement

Quick Links

Download this manual
User Manual of Laser Master 2
Laser Engraver
Dongguan Ortur Intelligent Technologies Co., Ltd.
(EN)Address: No. 56 Maxin Road, Changping Town, Dongguan 523565, Guangdong Province, China
(FR)Adresse: No. 56 Route Maxin, Changping Town, Dongguan 523565, Province de Guangdong, Chine
(DE)Adresse: 56 Maxin Road, Stadt Changping, Dongguan 523565, Provinz Guangdong, China
(IT)Indirizzo: No. 56 Maxin Road, Città Changping, Dongguan 523565, Provincia del Guangdong, Cina
(ES)Dirección: 56 Maxin Road, Ciudad Changping, Dongguan 523565, Provincia de Guangdong, China

Advertisement

loading
Need help?

Need help?

Do you have a question about the Laser Master 2 and is the answer not in the manual?

Questions and answers

Related Manuals for Ortur Laser Master 2

Summary of Contents for Ortur Laser Master 2

  • Page 1 User Manual of Laser Master 2 Laser Engraver Dongguan Ortur Intelligent Technologies Co., Ltd. (EN)Address: No. 56 Maxin Road, Changping Town, Dongguan 523565, Guangdong Province, China (FR)Adresse: No. 56 Route Maxin, Changping Town, Dongguan 523565, Province de Guangdong, Chine (DE)Adresse: 56 Maxin Road, Stadt Changping, Dongguan 523565, Provinz Guangdong, China (IT)Indirizzo: No.

  • Page 2: Brief Introduction

    Brief Introduction This Laser Master 2 laser engraver is a desktop laser engraver, not for  industrial use. There is a G-sensor on the motherboard for active position protection. If the  machine detects unauthorized movement, the laser beam will stop.
  • Page 3 Attention Do NOT operate laser without eye protection (Laser goggles)  Please set up laser engraver in the fireproofing area, with good ventilation.  Please keep minors (especially kids younger than 14 yours old) away from  this laser engraver. Minors of any age should not use this laser without direct Adult supervision and proper eye protection Please avoid strongly impact on the machine.

  • Page 4: Assembly Procedure

    Assembly Procedure Take out 1 piece of aluminum profile with length of 540mm and put 2 corner connectors into the slot. Pay attention to the installation direction. Take out 2 pieces of aluminum profile with length of 460mm, fixed with 2 pieces of M5*25.
  • Page 5 3. First lock the 4 screws on the corner connectors, then take out 4 pieces of M5 nuts and put 2 in the groove of each side of the frame. Locked the screws Locked the screws 4. First, take out 2 pieces of corner connectors and 1 pieces of aluminum profile with length of 540mm, load the corner codes into the aluminum profile, and then take out 2 pieces of M5*25 screws to fix the aluminum profile.
  • Page 6 5. Lock the 4 screws on the corner connectors, then installation of the bottom frame is done. Locked the screws Locked the screws 6. Take out the X-axis assembly and load it into the bottom frame.
  • Page 7 7. Take out 2 timing belts, 2 base anchors, 2 spacers, 4 M5*10 screws to assemble the base anchors on both sides and secure one end of the timing belt. 9. First, pass the timing belt through the rollers and timing pulley along the arrow in picture below, then take out 1 base anchor, 1 spacer, 2 M5*10 screws to assemble the base anchors and secure the other end of the timing belt.
  • Page 8 10. First, pass the timing belt through the rollers and timing pulley along the arrow in picture below, then take out the Y limit switch, 1 M5*10 screw and 1 M5 nut, to assemble the limit switch and secure the other end of the timing belt. (Please tighten the timing belt when lock screws)
  • Page 9 11. Please assemble the mainboard assembly on frame by 2 pieces of M5*10 screws. Please assemble the Y motor by 4 pieces of M3*8 screws. Pay attention to the direction of motor...
  • Page 10 13. Please connect laser and the backboard by 2 pieces of M3*8 screws. 14. Please assemble the laser assembly by 4 M5 cap nuts.
  • Page 11 15. Connect all the wires, and secured by cable tie. 6Pin plug Pass the cable tie through this hole to secure the wire 3Pin plug Pass the cable tie through this hole to secure the wire 4Pin plug connect with laser Black Pass the cable tie through this hole to...
  • Page 12 16. Assembly finished.

  • Page 13: Installation Program

    Installation Program 1. Please download the Host Control Software ”LaserGrbl” and the Drivers at: https://www.dropbox.com/s/xby8bad4jxdjgy0/Ortur.zip?dl=0 Or: https://tinyurl.com/rr2hsnq 2. Please install the appropriate driver for your Windows system VCP_xxx_Setup_x32.exe is for 32Bits computer system VCP_xxx_Setup_x64.exe is for 64Bits computer system 3. Please install the host control software, the Carving Software “LaserGRBL”in...
  • Page 14 4. Please plug the cable of power adapter into the Power Adapter Interface, press the Power Switch button, and connect the laser engraver and computer via USB cable. PS. Press the Power button, 0.5 second to power on, and press 2 seconds to power off.
  • Page 15 6. Please run the host control software “LaserGRBL”, and right click in the blank area of this lower section to get menu, then click ”Import custom buttons”, and select the profile file ”CustomButtons.gz” for advanced settings. TIPS: When the profile file ”CustomButtons.gz” imported, you could use LaserGRBL directly for this Laser Engraver.
  • Page 16 7. Advanced Settings Introduction...
  • Page 17 8. Setting Procedure：...
  • Page 18 9. Please adjust the laser focus. For your information: Please wear the safety goggles, then put the object under the laser lens. The best distance, from the upside of object to the bottom of heat sink (not lens), is 55mm. You could adjust the laser unit height at the acrylic holder plate.
  • Page 19 10. Please start the engraving. For your information: Please click this icon, to home X、Y axis. Please click these icons, to move the laser unit to be the correct position you want. Please click this icon, to set up the current position as the starting point of the engraving.
  • Page 20 Installation Program - LaserBurn Please download the aproproiate trial version of Laserburn from: https://lightburnsoftware.com/pages/trial-version-try-before-you-buy PS. If you think the trial version is good, you could pay for it. Install the software in your computer and run it. Launch the application from your computer (Windows, MAC, Linux). If it’s the first time you lauch LightBurn you will be prompted for the New Device Wizard.
  • Page 21 Select Serial/USB and press Next. Fill your Device Name, as well as X and Y axis and press Enter a. Ortur Laser Master b. X = 400 c. Y = 430...
  • Page 22 Select Front Left as your Origin X,Y and activate Auto “Home”, then press Next. Click Finish. 10. Select Ortur Laser Master and press Make Default. Your Ortur Laser Master is ready to be used in LaserBurn software.