Related Manuals for WoodFast MBS500
Summary of Contents for WoodFast MBS500
- Page 1 Instruction BANDSAW Manual 18-IN IMPORTANT For your safety, read instructions carefully before assembling or using this product. Save this manual for Original Instruction future reference. V.1-201306...
-
Page 3: General Information
INDEX GENERAL INFORMATION FOREWORD MACHINE IDENTIFICATION CUSTOMER SERVICE RECOMMENDATIONS SAFETY PRECAUTIONS SAFETY REGULATIONS RESIDUAL RISKS SAFETY AND INFORMATION SIGNALS SPECIFICATIONS MAIN COMPONENTS TECHNICAL SPECIFICATION ELECTRICAL CONNECTION NOISE LEVEL DUST EXTRACTION INSTALLATION INSTALLATION ZONE CHARACTERISTIC INSTALL OF LOOSE PARTS - INTRODUCTION ADJUSTMENT AND OPERATION SETTING TABLE SQUARE TO BLADE TILTING THE TABLE... -
Page 4: Machine Identification
MACHINE IDENTIFICATION There is a identification plate fixed to the machine, containing the manufacturer's data, year of construction, serial number and technical specifications. CUSTOMER SERVICE RECOMMENDATIONS Apply the machine to skilled and authorized technical staff to carry out any operation dealing with parts disassembly. Keep to the instructions contained in this manual for the correct use of the machine. -
Page 5: Residual Risks
- Never let unauthorized people repair, service or operate the machine. - The manufacturer is not responsible for any damage deriving from arbitrary modifications made to the machine. - Any transport, assembly and dismantling is to be made only by trained staff, who shall have specific skill for the specified operation. -
Page 6: Main Components
9 - Dust port 4 - Guard lifting handwheel 10 - Upper guide 5 - Upper door 11 - Bottom dust port 6 - Switch 12 - Table TECHNICAL SPECIFICATION MBS500 SPECIFICATION Motor Voltage 230V/50HZ 400V/50HZ 120V/240V/60HZ Motor power 1.5kW, S1 2.1kW, S1... -
Page 7: Electrical Connection
3.3 ELECTRICAL CONNECTION - Electrical installation should be carried out by competent, qualified personnel. - The mains connection should be made using the terminal box. - Replacement of the power supply cable should only be done by a qualified electrician. WARNING To avoid electrocution or fire, any maintenance or repair to electrical system should be done only by qualified electricians using genuine replacement parts. -
Page 8: Installation Zone Characteristics
- Workmen working in operations processing oak or beech timber where found to develop more often cancer of the mucous membrane of the nose (adenocarciome of the inner nose) then other workers. - Experience shows that skin contact with oak or beech dust does not cause cancer Wood dust and chips, together with an ignition source and the oxygen in the ambient air, can WARNING cause fires and explosions, injuries and allergies. - Page 9 4.2.2 INSTALL RIP FENCE - Install the rip fence as the picture shown, then set the fence block A along the guide rail B-Fig.4.2.1. Fig.4.2.2 4.2.3 FITTING CRANK HANDLE Attach the big crank handle A,B separately to the frame as the picture shown. Fig.4.2.3...
-
Page 10: Adjustment And Operation
5. ADJUSTMENT AND OPERATION WARNING Handle the tools with protective gloves. 5.1 SETTING TABLE SQUARE TO BLADE The table may be set at 90degree to the blade by adjusting the table stop screw under the table. The table stop screw rests on the top of the lower wheel bandwheel housing. - Page 11 5.4 ADJUST THE BLADE GUIDE To adjust the upper blade guides, first position the roller guides relative to the blade by slackening off the hex nut A and moving the guide carrier until the roller guides are approx. 1/16" behind the gullets of the blade.
-
Page 12: Troubleshooting
6. TROUBLE SHOOTING WARNING - For any information or problem contact your area dealer or our technical service center. The necessary interventions must be carried out by specialised technical personel. - Before carrying out any fault service or maintenance work, please always TRUN OFF THE SWITCH, UNPLUG POWER CABLE, WAIT FOR SAW BLADE TO COME TO STANDSTILL. - Page 13 -12-...
- Page 14 -13-...
- Page 15 -14-...
- Page 16 -15-...
- Page 17 -16-...
Need help?
Do you have a question about the MBS500 and is the answer not in the manual?
Questions and answers