Advertisement
Quick Links
Ortur4 V2 3D Printer Assembly Drawing
First Layer Of the Box
First Layer Of the Box
First Layer Of the Box
1st Layer Of the Box
2nd Layer of the Box
1
MicroSD Card &
Reader x1
Hardware Pack x1
Filament Tube x2
Filament Cutter x1
10m PLA Testing
Filament x1
X-axis Wooden
Horizontal Block x2
Power Cord x1
User Manual x1
Filament Holder for Ortur4-G2 x1
Ortur4-G1 does not have this part
No. 56 Maxin Road, Changping Town, Dongguan 523565, Guangdong Province, China
Dongguan Ortur Intelligent Technologies Co., Ltd.
Top Beam x1
Filament Holder for Ortur4-G1 x1
Ortur4-G2 does not have this part
X-axis Back Plate Components x1
Printer Chassis x1
Printer Chassis x1
Printer Chassis x1
Printer Chassis x1
Printer Chassis x1
Z-axis Linear Guide Rails x2
Z-axis Screw Rods x2
CE
www.ortur3d.com www.ortur3dprinter.com
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Ortur 4 V2
Summary of Contents for Ortur 4 V2
- Page 1 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Ortur4 V2 3D Printer Assembly Drawing MicroSD Card & Top Beam x1 Reader x1 Hardware Pack x1 Filament Tube x2 Filament Holder for Ortur4-G1 x1 Filament Cutter x1 10m PLA Testing Ortur4-G2 does not have this part...
- Page 2 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 1. Open the box, remove the Top Beam and Filament Holder, then connect the 2 pieces with 3 M4x6 screws. Combine them as seen below and set aside for later steps.
- Page 3 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 3. Take out the two Z-axis Linear Guide Rails and insert the rails into the square holes of the Printer Chassis. Note that the side mounting holes should be facing outward. There are differences between the two Z-axis Linear Guide Rails! Install the one with origin switch mounting holes on the left side, as shown in the red circle below.
- Page 4 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 4. Attach the Z-axis Linear Guide rails using 4 M4x6 screws (2 screws on each side). Do not fully tighten at this time! Step 5. Remove the X-axis Linear Guide Rail Components and X-axis Back Plate Components from the box.
- Page 5 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 6. Place the X-axis Assembly on the Z-axis Linear Guide Rails (that we previously connected to the printer chassis). No. 56 Maxin Road, Changping Town, Dongguan 523565, Guangdong Province, China...
- Page 6 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 7. Use a M3x6 screw to attach the bottom of drag chain (the chain can be gently pried open using a flat-head screwdriver), then open the socket protection cover, insert the wires to the matching socket tightly, and close the cover.
- Page 7 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 8. Remove the 2 Z-axis Lead Screws and gently guide them through the brass screw nuts and install in the couplers attached to the motors. Tighten the grub screws on the coupler (each coupler has 2 grub screws).
- Page 8 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 9. Prepare 2 M5x40 screws and install the beam assembly (assembled in Step 1) above the Z-axis Linear Guide Rails (pay attention to the direction). Now tighten the 4 M4x6 screws from step 4 (these were kept loose to ensure proper alignment and a square frame).
- Page 9 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 11. Turn both Z-axis Couplers, by hand, at the same time to move up the X-axis. Place the two Wooden Horizontal Blocks under the X-axis and move down the X-axis until it rests on both horizontal blocks (one on each side).
- Page 10 Dongguan Ortur Intelligent Technologies Co., Ltd. www.ortur3d.com www.ortur3dprinter.com Step 13. Press the Reset Button (below the control knob) to disable the X and Y motors. Move the print head by hand to the four corners of the hotbed. Using the leveling knobs, ensure there is a 0.1MM gap between the nozzle and the hotbed.
- Page 11 White Lightning grease, or other “dry lubricants” are a great option. Enjoy your ORTUR and let us know if there is anything we can do to improve your experience!
Need help?
Do you have a question about the 4 V2 and is the answer not in the manual?
Questions and answers