Conotec FOX-2PD Operation Manual

Version 0.98(2017.02.02)
OPERATION MANUAL
SAFETY AND CAUTION
Please carefully digest all cautions prior to the use of product, and
correctly operate.
※ The specification and external dimension may be changed for
improvement of product performance without advance notice.
WARNING
Being the product not manufactured for safety related
device, make sure to provide a duplicated safety apparatus
for use of controlling the devices subject to potential
personal injury and/or death, damages on critical peripheral
devices and substantial property losses.
Do not execute the wiring, checking and/or repair works
under the condition power supply is engaged.
3. Make sure to verify the correct terminal numbers and
terminate, when connecting the power supply.
CAUTION
• Please carefully read and digest the operation procedure and safety related
regulations or WARNING descriptions prior to the use of product, and make sure to
operate the product only per the relevant specification or within the corresponding
capacity rating.
• Do not make wiring or install the product on motor or solenoid with large inductive
loads. When extending the sensor, use the shielded wire not extending the extension
wire length unnecessarily long.
• Do not use the components generating arc when opening and closing under same
power supply line or near to power supply.
• Keep the power supply line away from high voltage wire, and avoid installation at the
locations subject to severe moisture, oily content and dust.
• Do not install the product at places exposed to direct sung light or rain.
• Do not install the product at places subject to strong magnetism or severe noise,
vibration and impact.
• Keep the product far away from the places directly producing strong alkali or acidic
substances using separate conduit for wiring.
• Do not spray water on the product for cleaning purpose when installed at kitchen area.
• Do not install at those places under the temperature and/or moisture exceeding the
rated capacity.
• Use the product paying attention not to have disconnected sensor wiring or defect.
• Allow the sensor wiring stay away from signal, power supply, drive and load wires
using separate conduit for wiring.
• Please note that no warranty services shall be provided when the product is
disassembled or modified at user's own discretion.
• The mark shown on Terminal Wiring Diagram is a safety notice notifying warning
or caution.
• Do not use the product at places near to the devices generating strong high frequency
noise (High frequency welding machine, high frequency sawing machine, high frequency
radio, large capacity SCR controller).
• Using the product with procedures not specified by the manufacture may incur the
personal injury or property damage.
• Not being a toy, do not allow children touch the product.
• Make sure to execute the installation only by the skilled person with related industry
or authorized personnel.
• CONOTEC Co., Ltd. shall assume absolutely no responsibility of whatsoever nature for those
damages and/or losses incurred due to the operation not complying with above WARNING
or NOTE descriptions or negligence and/or fault of user.
DANGER
CAUTION on Danger of Electric Shock
Electric Shock – Do not touch the AC power terminals when the
power supply is ON, as it may incur the electric shock.
Make sure to turn the input power supply OFF when checking the
input power supply.
PRODUCT CONFIGURATION
Model No. Sensor Control Output Temperature Range Application
Relay contacts
Relay contacts
Name of part
Appearance of product and name of part
output indication
output indication
output indication
output indication
Switch Increasing
Shift Function Switch
Switch Decreasing
Function of Operating key
Key assigned for temperature setting and program change
Key assigned for changing the temperature and
program setup values.
External Dimensions and panel size
Relay Wiring Example
Operating machine
(Load)
Operating machine
power supply
Relay Contact Output Terminal
The capacity rating of relay contact is below 250AC 2A.
Pay attention as engaging load exceeding the rated
capacity of contact may cause the fusing of contacts,
defective contact, damage of relay & etc.
Terminal Wiring Diagram
Termianl Wiring Diagram
Temperature
control
Temperature
control
Setting Range and Default Setup Value
Range
Function Display
TEMP 1
setting
TEMP 2
Temp.
setting
setting
TEMP 3
setting
TEMP 4
setting
User set-up temp.
upper limit setting
User set-up temp.
lower limit setting
Temperature
correction
Locking
Function
TEMP 1
Function
Select
TEMP 1
deviation
temp. setting
TEMP 1 output
delay time setting
Program TEMP 2
Function
setting
Select
TEMP 2 deviation
temperature setting
TEMP 2 output
delay time setting
TEMP 3
function selection
TEMP 3 deviation
temperature setting
TEMP 3 output
delay time setting
TEMP 4
function selection
TEMP 4 deviation
temperature setting
TEMP 4 output
delay time setting
Setting Value Changing Procedure
Temperature Setting
Indicate current temperature
Set
TEMP 1 change
Press the
Change the setting value
using
Set
TEMP 2 change
Press the
Default
Remark
Value
Change the setting values
using
Set
TEMP 3 change
Provided, not related
w/relay output
Press the
Provided, not related
w/relay output
Correction temp.
differs between
Indicated & Actual
Locking function setting
Locking function release
Change the setting values
Provided except temp. set value
using
purpose
purpose
Set
Output hysteresis
interval setting
TEMP 4 change
min sec
Press the
purpose
purpose
Output hysteresis
interval setting
min sec
Change the setting values
purpose
purpose using
Output hysteresis
interval setting
Set completed
min sec
Setting value storing mark
purpose
is displayed, then showing
purpose
the current temperature.
Output hysteresis
interval setting
min sec
key to display .
keys.
key to display .
keys.
key to display .
keys.
key to display .
keys.