Table of Contents
Advertisement
Quick Links
CCU Gen2A | Operations Manual
CCU
User Manual
This preliminary document presents the status of the agreed specifications. It will be confirmed when all the validations
has been completed with positive result
Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020
Product
Name:
Connectivity Control Unit
Family Model
Name:
Model
Name:
CU-304-0503
1 | 20
iTraMS CCU
Advertisement
Table of Contents
Related Manuals for Bosch CU-304-0503
Summary of Contents for Bosch CU-304-0503
- Page 1 Model Name: CU-304-0503 This preliminary document presents the status of the agreed specifications. It will be confirmed when all the validations has been completed with positive result Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020...
-
Page 2: Table Of Contents
Power Requirements .............................. 11 Annexure..................................12 Document Details ............................ 12 Document Revision History ........................12 Abbreviations Used ..........................12 EMC Recommendations .......................... 12 General Info .............................. 13 Pin-Out details ............................13 Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... - Page 3 CCU | User Manual 4 | 20 6.1 Main Connector ............................13 6.2 RF Connector ............................13 Best Practice for Wiring Routing ......................19 Grounding Scheme ..........................20 Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020...
- Page 4 Table of Figures Figure 1 Overview ............................... 8 Figure 2 3D model of the picture ..........................10 Figure 3 Wiring in iTraMS ............................13 Figure 4 Grounding Scheme ............................. 20 Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020...
-
Page 5: Introduction
The Primary antennas should always be separated from the operator or nearby person by a minimum distance of 20 cm. Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... -
Page 6: Agreed Product Use
Bosch does assume responsibility and does not provide any guarantee for the plug-in connection – in particular for its electrical functioning, durability and imperviousness – since this is Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... -
Page 7: Overview
Bosch shall not be liable for such products or any The equipment is operable within the • damage caused by such products. temperature range -40DegC +95DegC. Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... -
Page 8: Precautions For Installation
The functioning of other lines or cables Electromagnetic and Radio Frequency conformance is not impaired, or they are not clamped. tests and validations in different regions. The CCU should only be removed or Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... -
Page 9: Device Description
WARNING: Mismatch of the sequence may damage the connector NOTE: Un-used connectors (either Antenna Ports or Wired Connectors) must be closed appropriately to meet the specified IP rating of the product. Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... -
Page 10: Technical Specifications
The maximum operating current consumed by the external load of digital outputs. It is recommended to have a fast blow fuse with below rating, in series on the positive power line of 5A for 12/24V applications. Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... -
Page 11: Annexure
CCU ground shall be as short as possible fixed to chassis or directly to battery ground For CAN wiring, it is recommended to use a twisted pair (Figure 3). Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... -
Page 12: General Info
CAN1 : Low CAN1_High B_D_CAN1H CAN1 : High KL15 (Ignition) I_S_T15 6.2 RF Connector PIN NO SIGNAL NAME GNSS Antenna Port LTE Main Antenna Port LTE Diversity Antenna Port Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... -
Page 13: Best Practice For Wiring Routing
Wires splices and ground eyelets must be located away from direct contact with high pressure cleaner. Any wire end terminating in a splash water area should be orientated so that the wire end is pointing down. Robert Bosch Engineering and Business Solutions Private Limited | September 19 2020... -
Page 14: Grounding Scheme
CCU | Operations Manual 20 | 20 Grounding Scheme The grounding scheme for Gen2A is as seen below: Figure 4 Grounding Scheme Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020... - Page 15 CCU Gen2A | Operations Manual 20 | 20 Robert Bosch Engineering and Business Solutions Private Limited 123. Industrial Layout, Hosur Road, Koramangala, Bangalore – 560095, INDIA Email: Connect@in.bosch.com Official Website: www.bosch-india-software.com Robert Bosch Engineering and Business Solutions Private Limited | September 19, 2020...