Phoenix Mecano OKIN RF ECO BT M Quick Manual

Quick Guide RF ECO BT M

Acknowledgement:

The Pairing LED (b) will blink twice sound to signal the successful completion of thestep.

Teach-in for the RF remote or app:

To start using the RF remote with a Bluetooth
phone or tablet) with your system, you will first need to download and install the "OKIN" app for your device.

Automatic teach-in


Connect the RF ECO BT M to the drive system and put
thepower plug into thesocket.

The RF ECO BT M will be in pairing mode for 120sec which is
divided as follows: During the first 60sec, an RF remote can be
discovered (the teach-in). During the next 60sec, a
®
Bluetooth device can bediscovered.

The Pairing LED (b) and the Bluetooth
illuminated during this teach-in phase for the RFremote.
To pair the RF hand-held remote, please refer to the instructions
for the RF hand-held remote.
A successful pairing will be acknowledged.

The Pairing LED (b) will switch off after the teach-in process for
the RF remote is finished. The Bluetooth
®
with a Bluetooth device startsflashing.

®
The Bluetooth LED (c) switches off when the
®
Bluetooth pairing process has timed out or when the
device has connectedsuccessfully.
A successful pairing will be acknowledged.

If, during the RF remote's teach-in process, you press any
button on an already paired RF remote, then it switches to the
Bluetooth ® teach-inmode.

®
If the RF remote or a Bluetooth device is discovered during the
pairing phase, then this pairing mode is automatically ended.
The Pairing LED (b) and the Bluetooth

Repeat the automatic teach-in process. First, remove the plug
from the power supply. Then wait 60sec and insert the plug
back into the power supply. You can now start the new teach-in
process.

Paralleloperation:
Note! Put the drive systems into service one after the other. Do
not attempt to put several drive systems into service
simultaneously. Otherwise the drives will be unable to assign
the RF ECO BT M precisely.
Manuel teach-in
The system must be connected to the power supply.

Connect the RF ECO BT M to the drivesystem.

Quickly press the Pairing button (a) twice on the RF ECO BT
M. The Pairing LED (b) and the Bluetooth
illuminate. The RF ECO BT M is now in pairing mode for 120
seconds, which is divided as follows: During the first 60
seconds, an RF remote can be discovered (the teach-in). During
the next 60 seconds,a
®
Bluetooth device can be discovered.
03.12.2019
®
device, the wireless link with the RF ECO BT M must first be established. In order to use a Bluetooth

The Pairing LED (b)
illuminated during this teach-in phase for the RFremote.
To pair the RF hand-held remote, please refer to the instructions
for the RF hand-held remote.
A successful pairing will be acknowledged.

The Pairing LED (b)
the RF remote is finished. The Bluetooth
with a Bluetooth
®
LED (c) are

The Bluetooth
®
Bluetooth pairing process has timed out or when the
device has connectedsuccessfully.
A successful pairing will be acknowledged.

If, during the RF remote's teach-in process, you press any
button on an already paired RF remote, then it switches to the
®
LED (c) for pairing
®
Bluetooth teach-inmode.

If the RF remote or a Bluetooth
pairing phase, then this pairing mode is automatically ended.
The Pairing LED (b)

Paralleloperation:
Note! Put the drive systems into service one after the other. Do
not attempt to put several drive systems into service
simultaneously. Otherwise the drives will be unable to assign
the RF ECO BT M precisely.

Referencing the drive system

® LED (c) switchoff.
To enable all the functions of the drive system for use, you must
perform a reference test.

Press and hold the Pairing button (a) on the RF ECO BT M
until all drives reach their endposition.

Keep the Pairing button (a) pressed for a further 5seconds.

Successful pairing will beacknowledged.

Electrical reset function

(with battery connected to the drive system in a power outage)

Press the Pairing button (a) on the RF ECO BT M and
keep it pressed until the drive has retractedfully.

For the electrical reset function with the RF hand-held remote,
please refer to the instructions for the RF hand-heldremote.
Attention! After a test with the electrical reset function or when
®
LED (c) will
the system was de-energised, a reference test must be
performed.
GB
®
and the Bluetooth LED (c) are
will switch off after the teach-in process for
® LED (c) for pairing
®
device startsflashing.
®
LED (c) switches off when the
®
device is discovered during the
®
and the Bluetooth LED (c) switchoff.
93264 1.0
®
device (a smart

Saving the memory positions

To save the memory position of the RF hand-held remote, please
refer to the instructions for the RF hand-held remote.
Attention! Before saving the memory positions, a reference test
must be performed.

Resetting the factory settings


Give the Pairing button (a) 4x short press in succession.The
Pairing LED (b) lights on.

Now actuate the Pairing button (a) one times. The PairingLED
(b) lighting extinguishes.

The RF-remote isdeactivated.
RF ECO
BT M
b b
a

FCC Warning / IC Warning

FCC: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any changes or modifications not approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
c
2 / 9