Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Saey PEAK GAS S.C.
Summary of Contents for Saey PEAK GAS S.C.
- Page 1 SAEY PEAK GAS S.C. EN - Installation and user manual...
-
Page 4: Table Of Contents
CONTENTS ........................5 NTRODUCTION ........................... 6 ACKAGING ........................6 ECHNICAL DATA ..............8 ENERAL INFORMATION AND SAFETY INSTRUCTIONS ....................9 NSTALLATION INSTRUCTIONS ......................17 NSTRUCTIONS FOR USE ........................20 AINTENANCE ......................21 ROUBLESHOOTING ........................21 PARE PARTS ......................... 22 ARRANTY ........................ -
Page 5: Introduction
NTRODUCTION Congratulations! Thank you for choosing a SAEY stove. With SAEY, service does not end with your purchase! Our certified dealers and Fero Service guarantee the flawless operation of your stove, and therefore many years of heating pleasure. By registering your stove, you can also count on faultless after-sales service and warranty processing, and we can keep you informed of any news about your appliance. -
Page 6: Packaging
The packaging material used is environmentally friendly and therefore only recyclable packaging materials are used. If you dispose of the packaging yourself, do so according to the regulations or at a recycling centre. ECHNICAL DATA PEAK SAEY GAS S.C. Natural gas Liquefied gas Type of gas... - Page 7 Overview of pressure settings PEAK SAEY GAS S.C. Liquefied gasses Natural gas (G20) Natural gas (G25) (G30) with with overpressure with overpressure overpressure 20 mbar 25 mbar 30 mbar (calorific value (calorific value (calorific value Hi=34,9 Hi=34,02 MJ/m3, Hi=115,98 MJ/m3,...
-
Page 8: General Information And Safety Instructions
ENERAL INFORMATION AND SAFETY INSTRUCTIONS The following general safety instructions must be strictly observed: - During combustion, heat is released which causes the top of the stove, the doors, the door handles, the window, the smoke pipes and possibly also the stove mantle to heat up considerably. - Inform your children of this danger and keep them at a safe distance when using the stove. -
Page 9: Installation Instructions
NSTALLATION INSTRUCTIONS All local directives, including those relating to national and European standards, must be observed when installing the stove. Only an appliance connected by an installer guarantees the observance of the directives on building construction and fire prevention. This is absolutely necessary for the correct and safe operation of the stove. - Page 10 Placement of appliance The stove may only be installed on a floor with a sufficient load-bearing capacity. If the floor is not suitable, measures must be taken to increase the load-bearing capacity. In order to be able to place the appliance flatly, it is provided with adjustable feet (adjustment screws).
- Page 11 Connecting the chimney The stove must be connected to a chimney in accordance with the applicable standards and on the basis of the inspection report issued. The installation must be carried out only by an authorised expert in chimneys. The stove can only be started up after an inspection of the chimney and after the stove has been properly connected by the relevant specialist.
- Page 12 Installing ceramic logs The installation of the decoration is different fort he type of gas, follow the correct instructions. To avoid damage to the ceramic decoration, place the decoration after the installation of the stove, so that you do not have to move the stove. The first step in the installation of the decoration is to free the door, a description of which is given in Article 6.
- Page 13 Step 3 Place the two rear imitation firewood logs in the fire chamber so that they lie completely in the corners on the granulate - see illustration. The logs may not be placed outside the granulate. The distance to the burner is approximately 20 mm.
- Page 14 This procedure is only necessary if the stove is connected to G30! Follow the instructions correctly to avoid damage to the stove Step 1 Place the imitation coals on the steel plate exactly as shown below. Make sure that the correct distances and dimensions are respected and also make sure that the coals fit properly with the burner plate.
- Page 15 Place the imitation wood front shown on the burner plate, tightly against the edge. Attention ! The ignition(s) must remain free and may not be overlapped. Also make sure that no granules get between the flames of the burner and the thermocouple. Step 4 Place both rear imitation blocks one by one in the burner chamber, so that they rest nicely on the imitation charcoal - see arrows.
- Page 16 Step 6 Place the lateral logs on the side of the burner chamber and also on both rear imitation logs. Step 7 Chose the burner chamber Clean the inside of the sight glass and make sure that the ignitions are not covered with granules. Close the burner chamber and seal it with the countersunk self-tapping bolt.
-
Page 17: Instructions For Use
NSTRUCTIONS FOR USE Location of controls A – control knob 1 and piezo ignition knob 2 B – the universal fitting of figure 4 or the BY-PASS sliding controller C – placement of the thermostatic Putting into operation - Open the gas supply valve; - Turn knob 1 to the ignition position * and push it in as far as it will go - Press the piezoelectric ignition button 2. - Page 18 Switching off the heating For a short period: turn knob 1 all the way to the right For a longer period (vacation,…): turn knob 1 all the way to the right and close the gas supply If the main burner does not start immediately after a prolonged period of inactivity, be sure to observe the 60 second interval.
- Page 19 Manual control Thermostatic operation is deactivated when the slider 3 is no longer in its standard position. With this slider we can regulate the power and the size of the flame. By moving the slider from the zero position, we can thus manually increase the burner output. Attention! As the thermostat is switched off, you can no longer regulate the temperature with knob 1.
-
Page 20: Maintenance
AINTENANCE All operations and applications mentioned in this document may only be performed by a certified technician with the appropriate skills and documents. Regular inspection of the gas fire by a technician will ensure that your appliance is working properly. We therefore recommend that you check the operation of the appliance and all parts that come into contact with gas regularly to ensure that they are still secure. -
Page 21: Troubleshooting
ROUBLESHOOTING Before contacting a service technician, please check whether you can remove the problem yourself by following the steps again. Error description Possible cause Solution The heater (pilot burner) Equipment valve is closed Open the valve cannot be ignited. Air in the gas fitting (after a Turn the ignition control knob to long interruption of operation the ignition position for a long... -
Page 22: Warranty
ARRANTY Your stove is guaranteed for 2 years against all manufacturing defects, from the date of installation and provided that it is used in accordance with the installation instructions and user manuals. Your receipt or invoice stating the date of purchase is your certificate of guarantee. This guarantee is limited to the repair or replacement of parts that show defects under normal use. - Page 23 Please contact your installer in case of maintenance or operation problems Industriepark De Bruwaan 17 9700 Oudenaarde Belgium www.belgofire.be Versie 08 2021...
Need help?
Do you have a question about the PEAK GAS S.C. and is the answer not in the manual?
Questions and answers