Advertisement
QUICK START GUIDE
AUTOMATIC DIGITAL WRIST BLOOD PRESSURE MONITOR
Please watch the following User Video on your computer by typing in the link
https://www.medline.com/sku/item/MDPMDS4003
Step 1 – Install Batteries
A) Slide battery
cover off.
B) Install two (2)
"AAA" batteries.
C) Slide battery cover
back on.
Step 2 – Set Date and Time
A) Hold down MEM until the year appears in
the lower left corner. If the year is already
flashing, proceed to step C.
B) Release the MEM button.
C) Press MEM repeatedly to change the year.
D) Press
once to change to month selection.
Press MEM repeatedly to change the month.
E) Repeat step D to set the day.
F) Press
to go to clock format. Press MEM to
alternate 12 hour and 24 hour clocks.
G) Press
once to change to hour selection.
Press MEM repeatedly to change the hour.
H) Repeat step G to set the minute.
I)
Press
twice to save and exit.
Step 5 – Begin Measurement
A) Press
to turn monitor on and automatically
begin measurement.
1) Does Not Turn On
❏
Check that the batteries are inserted and
battery cover is on.
❏
Check that the battery polarities ( + and –symbols)
are positioned in the correct direction.
❏
Try inserting new batteries.
2) Inaccurate Reading
❏
Refrain from eating, smoking and drinking
(especially alcoholic beverages) before a
measurement.*
❏
Check the cuff for a snug fit.
❏
Ensure that you are not moving, speaking or
repositioning during reading.
❏
Wait at least 3 minutes between readings.
MDS4003
Troubleshooting Guide
Step 3 – Cuff Placement
A) Position the edge of the cuff about 1-1.5 cm
from wrist joints.
B) Fasten the cuff around your wrist, with no
room between the cuff and skin.
C) The LCD cuff display should face you and be
at the level of your heart.
Step 4 – Body Placement
A) Sit with feet flat on floor.
B) Place elbow on a table, so that the cuff is at
the same level as your heart.
C) Turn your palm upwards.
3) Inflation Problem
❏
Check that the cuff is wrapped snugly around
your bare wrist.
❏
Confirm that you are remaining still during
measurements.
*Other things can affect blood pressure values
besides those listed here.
IMPORTANT! You can STOP the inflation or deflation
of the cuff at any time by pressing the
Please see User Manual for more details.
If you have any questions or are experiencing
difficulties, please call the Medline Service Center at
1-800-MEDLINE (1-800-633-5463). V1 RJ20GTE
1-1.5cm
button.
Advertisement
Table of Contents
Need help?
Do you have a question about the MDS4003 and is the answer not in the manual?
Questions and answers
Why does the LO come on after 2 days of newly batteries installed on Medline MDS4003?
The LO indicator on the Medline MDS4003 may activate after 2 days of new batteries due to one or more of the following reasons:
1. Battery Quality or Type: If different types of batteries or a mix of new and used batteries were installed, the device may not function properly. The manual advises against mixing batteries.
2. Battery Drain: If the device was left on for an extended period or used frequently, the batteries may have drained faster than expected.
3. Faulty Batteries: Some batteries may be defective or not provide sufficient power, causing the LO indicator to appear.
4. Device Malfunction: If the device has an internal issue, it may incorrectly detect low battery levels.
To resolve the issue, replace the batteries with fresh, high-quality AAA batteries of the same type, ensuring they are properly installed. If the issue persists, the device may need servicing.
This answer is automatically generated