Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Orico 95RU3 Series
Summary of Contents for Orico 95RU3 Series
- Page 1 95RU3 Series 3.5 Inch External HDD Enclosure User Manual...
-
Page 2: Table Of Contents
Specifications ......................3 Product features ......................3 Product Illustration ..................... 4 Set up RAID ........................5 Set through ORICO HW RAID Manager Software ............6 Attention ........................13 Remove the Device ....................13 Hard-drive Format Partition Operation ..............13 Failure Solutions ....................... 17 Notice ......................... -
Page 3: What Is In The Box
Thank you very much. Product Introduction ORICO 95 series RU3 is a multi-bay 3.5 inch SATA hard drive enclosure. Aluminum alloy material coupled with the quiet fan, making it a good heat-dissipation performance. Meanwhile, it is designed with over current, short-circuit protections for the disk and data. -
Page 4: Specifications
Specifications Model 95RU3 Series Material Aluminum Alloy Surface Frosted Input SATA3.0 Output USB3.0 Type-B Transmission Rate 5Gbps Data Cable USB Type-A/M To USB Type-B/M 9558RU3 AC100-240V Power Cord Power Supply 9548RU3 AC100-240V Power Cord 9528RU3 12V 3A Power Adapter 9558RU3 264(L)×146(W)×199.5(H)mm Dimensions 9548RU3 264(L)×146(W)×164.5(H)mm... -
Page 5: Product Illustration
Product Illustration 9528RU3 ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ① Power Interface ② USB3.0 Interface ③ RAID button ④ SET ⑤ Power Switch ⑥ LED Indicator ⑦ Keyhole ⑧ Bay 9548RU3 ① ②③ ④ ⑤ ⑥ ⑦ ⑧ ①... -
Page 6: Set Up Raid
9558RU3 ① ②③ ④ ⑤ ⑥ ⑦ ⑧ ① Power Interface ② RAID button ③ SET ④ USB3.0 Interface ⑤ Power Switch ⑥ LED Indicator ⑦ Keyhole ⑧ Bay Set up RAID · Note 1. Introduction of RAID Mode This product supports RAID 0, RAID 1, RAID 3, RAID 5, RAID 10, Big and Normal. RAID 0: Merge all HDDs' capacity in the HDD enclosure and upgrade its performance (reading &... - Page 7 RAID 10=RAID 0 + RAID 1 Big= Merge all HDDs' capacity in the HDD enclosure to make it easy to manage but cannot upgrade its performance. Normal=Normal state, all HDDs in the HDD enclosure work independently without forming any RAID modes. 2.
- Page 8 Press and hold the "SET" button, then boot the enclosure, and release the SET button after about 10 seconds, that is, the RAID mode is successfully set. Note: After the RAID is successfully formed, a new hard disk will be generated. It must be initialized and formatted before it can be used normally.
-
Page 9: Set Through Orico Hw Raid Manager Software
Set through ORICO HW RAID Manager Software 1. Download and install ORICO HW RAID Manager from ORICO official site. Please unzip it before operating if the software is RAR form. 2. Turn off the HDD enclosure, run Setup.exe of installation program and start installing as the following pictures show. - Page 10 3. The shortcut of ORICO HW RAID Manager software will appear on PC desktop after finishing the installation. Please turn on the power of the HDD enclosure and HDD, double click to run the software to set or manage RAID.
- Page 11 Note： Please confirm the HDD enclosure and HDDs are under Normal mode before setting your required RAID mode. Or you could set Normal mode in advance before setting or changing to the required RAID mode. 5. Pop up the following interface and click "Yes" to set the chosen RAID, click "No" to cancel the setting.
- Page 12 6. After click "Yes", setting will be started automatically and the progress bar will show you setting progress. Pop up the prompt interface to let you know the setting is finished. - 11 -...
- Page 13 7. HDDs or HDD group that has been set RAID mode will be displayed on computer later and it can be started to use after initiating and partitioned formatting. (Please try to restart the HDD enclosure and computer or reset RAID mode if the formatting of HDDs or HDD group is fail.) 8.
-
Page 14: Attention
You need to initialize and format the partition first, otherwise it won't work properly. If it is a brand-new hard drive, please initialize and format the partition according to the following steps: 1.Please ensure the ORICO enclosure is installed properly, and connected to the computer. - 13 -... - Page 15 2.Right click “My Computer”, then select “Computer Management”, tap or click “Disk Management” on the left side of the window when “Computer Management” opens, then select “MBR” or “GPT” partition form and click “OK” Note: ・If the disk capacity is less than 2TB, please use MBR partition form to initialize the hard disk.
- Page 16 （4）When setting the capacity of disk partition, can customize the partition capacity, or set the default maximum simple volume size, and there will be only one disk partition. （5）Allocating the drive letter and path, (e.g. Explorer, C, D, E, F, G drive) drive letter. - 15 -...
- Page 17 （6）Format partition, able to set file system format (NTFS, FAT32 or exFAT), assign unit size (default set), volume label name, recommend "perform quick format", and click "next" when configuration is completed （7）Click "finish" to perform the final step of formatting partition. - 16 -...
-
Page 18: Failure Solutions
（8）It will take 5-30 seconds, and the new partition drive letter will be displayed in the explorer after formatting. Failure Solutions If the product cannot be recognized in the computer, please try to solve the issue according to the following methods: ·... -
Page 19: Declaration
Declaration ORICO Technologies Co., Ltd., all rights reserved. Thank you so much for purchase ORICO product. Please refer to this manual when using orico product or experienced issues. Additionally, please kindly contact ORICO customer care team if any concern. ORICO® is registered trademark of ORICO TechnologiesCo., Ltd.. Any other product, trademark, service or company mentioned herein is trademark or registered trademark of the respective owners. - Page 20 ORICO Technologies Co.,Ltd. Hotline: 400-6696298 Tel: 86-755-25196059 Website: www.orico.cc E-mail: supports@orico.com.cn Company Add: 19/F, Block 14A, Zhonghaixin Science &Technology Park, Longgang District, Shenzhen, China Factory Add: Room 201, Building 11, No. 24, Tangjiao Road, Changping Town, Dongguan City, Guangdong, China...