Safety Instructions Please read these safety instructions carefully. Please keep this User‘s Manual for later reference. Please disconnect this equipment from connecter before cleaning. Don‘t use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning. Make sure the voltage of the power source when you try to connect the equipment to the power outlet.
Make sure that the system power is turned off. Plug the signal cable to the signal connector at the rear of PC. Plug adapter output cable to the jack at the rear of LCD monitor and the power cord to the adapter.
Do not expose the monitor to direct sunlight or heat. Do not spill liquid on the monitor. Do not attempt to open the monitor. You may be hurt by electric shock. For service, call your place of purchase. Do not use your monitor when magnets or electronic products are operating nearby.
Hardware Installation Be careful to your LCD monitor. It’s very delicate and easy to break. Turn off LCD’s and PC’s power before installation. Follow the installation step by step described below. Input 【1】POWER-IN:This is for connecting the power cable 【2】AUDIO-IN:This can be connected to the audio-out connector of any sound resource.
Page 9
19.0 TFT Active Matrix LCD Panel User Manual 【3】VGA-IN : This can be connected with the D-Sub 15 pin signal cable. 【4】DVI-D input:This is the connector for digital video signal inputs (option) English 9...
2. Turn your monitor upside down carefully with panel facing you to locate all connector port. Plug in signal cable to VGA-IN of the monitor and the other side of the cable to the computer. 19.0 TFT Active Matrix LCD Panel User Manual...
Page 11
Connect the audio cable to AUDIO-IN on the monitor, and the other side to computer line out. 5. Plug in signal cable to DVI-D of the monitor and the other side of the cable to the computer. 6. Plug power cord onto the AC-IN on monitor.
5 degrees or backward inclination of 15 degrees. The flexible design of this monitor allows user to store from the perpendicular angle to horizontal angle by keeping the locking-hitch unlocked showing above. Please refer to the figures below.
Auto Adjust OSD Menu There 5 keys for user to set up the monitor, including “Power”, “MENU “, “AUTO”, ” <-> Down”, ” <+> Up”. Please refer to the introduction below. “Power”: Turn the LCD power on and off. When the power is on, the light turns green, and standby in the color of orange.
Troubleshooting If you encounter any trouble in using the monitor, make sure your monitor is properly installed according to the following steps before you call for service. ˙ There is no picture on the screen. Check: 1. Power saving mode. Press any key and move the mouse to deactivate the mode.
Page 15
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) BRIGHTNESS: Adjust the difference between light and dark area. BRIGHTNESS COLOR ADJUST: Adjust the RED, GREEN, and BLUE colors of the display Click “ENTER” to adjust the R.G.B.
Page 16
OSD (On-Screen Display) Menu Mode (PC Mode) COLOR TEMP: Adjust the color temperature of the display BACK : Return to the Main Menu Screen COLOCK: Adjust the re-flash ratio of the vertical scanning area. PHASE: Adjust the re-flash ratio of the horizontal scanning area.
Page 17
OSD (On-Screen Display) Menu Mode (PC Mode) AUTO ADJUST: Automatically adjust the re-flash ratio of both vertical and horizontal scanning areas of the display H. POSITION: Adjust the horizontal viewing area of the display V. POSITION: Adjust the Vertical viewing area of the display BACK : Return to the Main Menu Screen...
Page 18
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) OSD H. POS: Adjust the Horizontal position of the OSD OSD H. POS OSD V. POS: Adjust the Vertical position of the OSD OSD V. POS OSD TIME: Adjust the displaying time of the OSD OSD TIME...
Page 19
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) OSD ALPHA: Adjust the Alpha volume of the OSD displaying OSD ALPHA BACK: Return to the Main Menu Screen BACK LANGUAGE: Change the language support to the language displaying of the OSD.
Page 20
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) VOLUME: Adjust the sound volume of the embedded speaker of the display VOLUME MUTE: Silence the embedded speaker of the display MUTE BACK : Return to the Main Menu Screen BACK VGA / DVI: Switch to the VGA / DVI Signal inputs of...
Specification LCD Panel Type Viewing Angle Contrast Ratio Brightness Response Time Display Colors Max Resolution Pixel Pitch Input Signals RGB Analog Compatibility Connector RGB Analog Audio IN DVI-D Power AC input Voltage Consumption Power saving mode Internal Speaker User Interface LED Indicator Operating Temperature...