Commercial refrigeration unit cooler medium & low temperature (21 pages)
Summary of Contents for Daikin LXE10E-A18A
Page 1
ダイキン海上コンテナ冷凍装置 Marine type Container Refrigeration Unit サービスガイド・パーツリスト Service Manual・Parts List オプション機能編・Optional Functions LXE10E-A18A LXE10E-A18B LXE10E-A30 TR05-09A...
Page 2
Covered Models Regarding the features and operation of the unit, the service guide describes the items which are different from those of the service manual TR01-09A. Different points from service manual Item (Maintenance and Repair) Tightening lever for control box cover...
Page 3
CONTENTS Safety Precautions 3.10 Chartless function ........3-56 • Danger ..............3 3.10.1 Chart indication function.....3-56 • Warning..............4 3.10.2 P code (Pull down time indication) ..3-58 • Caution..............5 3.10.3 Chartless code display function..3-59 1. Introduction ............1-1 3.10.3.1 List of chartless code....3-59 1.1 Operation range ..........1-1...
CONTENTS NAMES OF COMPONENTS ……………………………………………5 1.1 Outside …………………………………………………………………5 1.2 Inside …………………………………………………………………6 FROZEN MODE ……………………………………………………………7 2.1 Control state transition and common control ………………………7 2.2 Operation of magnetic contactor and solenoid valve ……………7 2.3 Set point temperature and control sensor …………………………8 2.4 Control …………………………………………………………………8...
Page 5
CAUTION Before starting the unit, run the generator. Securely close the control box cover and the temperature recorder box cover (optional). Otherwise, It will cause water entry. Temperature recorder box cover TransFRESH (A30 only) Control box cover Trans FRESH Quick-lock lever...
2. FROZEN MODE 2.1 Control state transition and common control Thermostat ON (Pull-down range) ●Compressor Running ●Evaporator fan Low speed (L) Continuous compressor running for ≤ ≤ 2 minutes or more and RS SP - 0.5˚C RS > SP + 0.5˚C Pump down ●Compressor...
2.3 Set point temperature and control sensor When the set point temperature (referred to as SP hereafter) is –10.1˚C(+13.8˚F) or lower, the compressor is operated ON and OFF, in response to return air temperature. 2.4 Control qWhen the control temperature reaches SP-0.5˚C (point A), the compressor and condenser fan are turned off after the − ...
3. DEFROSTING OPERATION (1) Defrosting system A hot-gas defrost system is adopted in the units; i.e. the high temperature and high pressure refrigerant (hot gas) from the compressor is sent to the evaporator and drain pan for defrosting. Since the evaporator is heated directly by the hot gas (refrigerant), defrosting can be performed effectively.
Page 11
(4)Defrosting Interval Automatic Changing Function What is the Defrosting Interval Automatic Changing Function? This is a function to measure the time required for defrosting operation with the "long timer"and, according to the measurement, changes intervals of the defrosting operation. If a lapse of time after...
4. DEHUMIDIFICATION CONTROL SETTING This unit features the dehumidification function. Therefore, it is necessary to set whether the dehumidification control is to be executed or not according to the cargo to be transferred. You can set whether the dehumidification control is to be executed or not by operating the display panel of controller.
4.2 Dehumidification control ※If reheat coil (Optional) is equipped: The unit have dehumidification control by a reheat coil, which is under the evaporator coil. In dehumidification, the Reheat Solenoid Valve (RSV) opens to give high pressurized refrigerant to reheat coil. The "DEHUMID" LED lamp will light up.
–3 –2 –1 DECOS DAIKIN ELECTRONICCONTAINER OPERATION SYSTEM Operation key ① SUPPLY LED (Lights when "supply air temperature" is indicated.) ⑦ IN RANGE LED (Lights when the control temperature is in range.) ② RETURN LED (Lights when "return air temperature" is indicated.) ⑧...
6. OPERATION PROCEDURE 6.1 Operation procedure flow chart When no power supply ※ 3 Battery mode, Operation Condition Setting with back-up battery (Set Point Temperature˚C / Humidity %, / Defrost Internal) Power OFF Non operation for 30 sec. Circuit Breaker ON...
7. G-SET OPERATION/AUTOMATIC PUMP DOWN OPERATION MODE/DEHUMIDIFICATION ON-A・OFF SETTING The energy consunption reducing operation during G-SET operation, automatic pump down operation collecting refrigerant to the liquid receiver and dehumidification ON-A・OFF setting are executed. All indication light on (for 3 sec.)
Page 17
Setting item LED panel LCD panel Setting method Current –– –– –– indication mode MODE ON, OFF diSPOFF Select ON by using key, and press G-SET key to determine operation the setting. MODE MODE ON, OFF P down Select "ON" by using...
8. SETTING FLOW CHART This configuration setting flow shall be utilized, when Case 1) Where USDA cool transportation setting, defrosting interval automatic changing function, or dehumidification control clearing function is required. (Optional function setting) Case 2) Where an urgent change of container ID to other ID should be made.
8.2. Optional function setting mode Following functions can be set up. With/Without setting of USDA sensor, With/without setting of cargo temperature, With/Without setting of dehumidification control, ON/OFF setting of dehumidification control clearing function, and ON/OFF setting of dehumidification control clearing function <Key operation to enter/exit>...
Page 21
<Key operation in this mode> Whenever the key is pressed, the display changes. Turn the power breaker OFF after the setting. To set the USDA ON/OFF and CARGO TEMPERATURE SENSOR ON/OFF: Select "OFF (not in use)", "3 (3 USDA probes are in use)", or "4 (3...
9. TEMPERATURE SENSOR (Example) 9.1 Sensor calibration ● Supply and Return air sensor (SS/RS/DSS/DRS) q Prepare the ice bath w Cut the binding of each sensor and put them into the ice bath e Turn on the unit and display "Sensor calibration (CAL)"...
10. AUTOMATIC PUMP DOWN An automatic pump down system is applied to the unit to prevent the unit operation from extra decreasing of low pressure due to pump down operation or burning of scroll compressor due to close stop valve.
11. CABLE CLAMP BRACKET cable clamp When it is operated on the trailer or railway chassis, be sure to fasten the power cable with CABLE CLAMP LOOSE CLAMP...
12. MANUAL CHECK SELECTION MODE The LED indicate the values of following items. Compressor operating time, Evaporator fan motor high-speed running current, Evaporator fan motor low-speed running current, Condenser fan motor running current, Battery life, Horse power, Elapsed time after trip start, Evaporator fan motor running time, Condenser fan motor running time, Controller software version and sensor calibration.
13. ELECTRONIC TEMPERATURE RECORDER ●Temperature record with power supply turned off When the power supply is turned off, the pen will move to the outer circumference of recording sheet simultaneously. Power supply is turned off. ●Rechargeable battery The rechargeable battery is equipped on the electronic temperature recorder.
14. TransFRESH (LXE10E-A30 only) Attachment for the TransFRESH CA devices are provided to control the internal atmosphere (quantity of O and CO Use the CA devices according to the Operation Manual supplied by TransFRESH. The controller and sensor included in the CA devices are installed by the TransFRESH's agents before each transportation.
Page 29
●An example of installation of CA devices, inside q TransFRESH ASS'Y A4&A5 CABLES W/MOUNTING BOX...
14. TransFRESH(LXE10E-A30のみ) 庫内雰囲気(O 量、CO 量)の制御を行うため、TransFRESH社のCA装置用アタッチメントが取付いてい ます。 CA装置の取扱いにつては、TransFRESH社のマニュアルに従ってください。また、CA装置のコントロー ラ、センサ等は、各輸送の度に、TransFRESH社のエージェントにより取付けられます。 ●CA装置取付位置例・庫外側 Trans FRESH ① Trans FRESH SECURITY ENCLOSER ② Trans FRESH COMMUNICATION BRACKET ③ Trans FRESH SINGLE PURGE PORT...
Page 61
●CA装置取付位置例・庫内側 ① Trans FRESH ASS`Y A4&A5 CABLES W/MOUNTING BOX...
Page 66
ORDERING INSTRUCTIONS The parts list contains the parts of the DAIKIN Marine Type Container Refrigeration Units. Please read the following items before using the list. 1. When ordering the parts, be sure to specify the model No., the name of part and the type of part.
Page 67
Denomination of Model Name L X E NOMINAL HORSE POWER 5 : 5 10 : 10 CONDENSER COOLING TYPE NIL : AIR and WATER COOLED TYPE A : AIR COOLED TYPE OPTION NUMBER Note) "R" GIVEN AFTER OPTION NUMBER STANDS FOR "REVISION"...
Page 68
C O N T E N T S 目 次 Page A. Parts related with the unit(outside)………………………………………………………………………68 庫外関連部品 B. Parts related with refrigerant piping(outside) …………………………………………………………72 庫外冷媒配管関連部品 C. Parts related with the unit(inside) ………………………………………………………………………76 庫内関連部品 D. Parts related with refrigerant piping(inside) …………………………………………………………80 庫内冷媒配管関連部品...
Page 69
Parts related with the unit(outside) 庫外関連部品 − 68 − (TR05-09A)...
Page 70
Parts related with the unit(outside) 庫外関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1549647 Power plug (400V class) 3P130172-1 電源プラグ(400V) 0954936 Condenser fan motor 3P005566-1 凝縮器電動機...
Page 71
Parts related with the unit(outside) 庫外関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1637847 Plug holder 3P158122-1 プラグホルダー − 70 − (TR05-09A)...
Page 72
Parts related with the unit(outside) 庫外関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B − 71 − (TR05-09A)...
Page 73
Parts related with refrigerant piping(outside) 庫外冷媒配管関連部品 − 72 − (TR05-09A)...
Page 74
Parts related with refrigerant piping(outside) 庫外冷媒配管関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1315426 Compressor JT224DBNYR 圧縮機 1387173 Air cooled condenser 2P089486-1 CA-LXE10E1 空冷凝縮器 Discharge pipe ass'y 2P117329-1 吐出配管組立品...
Page 75
Parts related with refrigerant piping(outside) 庫外冷媒配管関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B B7-8 0964166 Strainer 4P012568-1 ストレーナ 1496781 Suction pipe ass'y (inside) 3P071569-2 吸入配管組立品(庫内)...
Page 76
Parts related with refrigerant piping(outside) 庫外冷媒配管関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B − 75 − (TR05-09A)...
Page 77
Parts related with the unit(inside) 庫内関連部品 − 76 − (TR05-09A)...
Page 78
Parts related with the unit(inside) 庫内関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 0955333 Three phase AC fan motor 3PA07524-4 三相交流ファン電動機 0955340 Three phase AC fan motor...
Page 79
Parts related with the unit(inside) 庫内関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 860005 Washer, speed bolt R4713334 スピードボルト用座金 1685187 Washer 4P170127-5 木材座金M5用(φ20) 840002 Drop out prevention washer R4718607-6 脱落防止座金...
Page 80
Parts related with the unit(inside) 庫内関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B − 79 − (TR05-09A)...
Page 81
Parts related with refrigerant piping(inside) 庫内冷媒配管関連部品 − 80 − (TR05-09A)...
Page 82
Parts related with refrigerant piping(inside) 庫内冷媒配管関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1380691 Evaporator ass'y 2P071832-1 CRB-LXE10E1 蒸発器組立品 1683927 Evaporator ass'y 2P163797-1 CRB-LXE10E9 蒸発器組立品...
Page 83
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) − 82 − (TR05-09A)...
Page 84
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) − 83 − (TR05-09A)...
Page 85
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) − 84 − (TR05-09A)...
Page 86
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) − 85 − (TR05-09A)...
Page 87
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) − 86 − (TR05-09A)...
Page 88
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1266694 Set plate, discharge pipe 4P079462-1 Page83 吐出配管取付板 1485938 Mounting plate...
Page 89
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1381043 Sealing materialL(patch plate3) 4P095038-1 Page85 シール材(当板3) 1266997 Sealing material(patch plate1) 4P068968-1 t5.0...
Page 90
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B − 89 − (TR05-09A)...
Page 91
Control box コントローラボックス − 90 − (TR05-09A)...
Page 92
Control box コントローラボックス − 91 − (TR05-09A)...
Page 93
Control box コントローラボックス QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 844022 Plain washer 4SK07005-12 平座金 1549849 Wire harness ass'y (Monitoring receptacle) ワイヤーハーネス (モニタリングレセプタクル) 4P121213-1-KA 1136407 Hinge (recorder/box cover) 平蝶番(レコーダボックス蓋)...
Page 94
Control box コントローラボックス QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B F34-4 1295584 Controller cover 2P085424-1 t1.2 蓋(コントローラ) F34-5 1099940 Support bushing, PCB プリント基板サポートブッシュ MI49531-11 F34-6...
Page 95
Parts related with name plate 銘板関連 − 94 − (TR05-09A)...
Page 96
Parts related with name plate 銘板関連 − 95 − (TR05-09A)...
Page 97
Parts related with name plate 銘板関連 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1448434 Name plate, ventilator 4P113967-1 換気口銘板 1267952 Name plate, ventilator arrow 4P018502-1 ベンチレータ矢印銘板...
Page 98
Parts related with name plate 銘板関連 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B − 97 − (TR05-09A)...
Page 99
Parts related with option 1 – Recorder box オプション関連部品1 – レコーダボックス − 98 − (TR05-09A)...
Page 100
Parts related with option 1 – Recorder box オプション関連部品1 – レコーダボックス QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A18A A18B 1633092 Recorder box ass'y for welding 2P044870-6 レコーダ BOX溶接組立図...
Page 101
Parts related with option 1 – Recorder box オプション関連部品1 – レコーダボックス QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME LXE10E- 部品名称 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1267921 Protection sheet, recorder chart 保護シート 4P015666-1 1136407 Hinge (recorder box cover) 平蝶番...
Page 102
Parts related with option 1 – Recorder box オプション関連部品1 – レコーダボックス QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B − 101 − (TR05-09A)...
Page 103
Parts related with option 2 – USDA オプション関連部品2 – USDA関連 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1135125 Hinge 3P043374-1 蝶番 1549940 Inspection door (USDA) 4P094962-1 点検蓋(USDA)...
Page 104
Parts related with option 3 – MODEM オプション関連部品3 – モデム QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1448410 Mounting plate (modem) 4P081133-1 取付板(モデム) 1267743 Connector for MODEM 3P010371-7 モデム用コネクタ...
Page 105
Storage for power cable ケーブル収納 − 104 − (TR05-09A)...
Page 106
Storage for power cable ケーブル収納 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 351237 Hinge R4717906-1 蝶番 1295731 Cable clamping metal fitings ケーブルクランプ金具 (リベット止メ) 4P071189-1 t1.5...
Page 107
Parts related with option 4 – TRANS – FLESH オプション関連部品4 – トランス・フレッシュ − 106 − (TR05-09A)...
Page 108
Parts related with option 4 – TRANS – FLESH オプション関連部品4 – トランス・フレッシュ QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 部品名称 LXE10E- 符号 部品番号 図面番号 形式 仕様 備考 A30 A18A A18B 1634235 A2 cable ass'y 3P145459-1 A2ケーブル組立品...
Page 109
List of size for standard pipe clamp 配管固定具サイズ表 1.Resin clamp 1.樹脂バンド (外穴) (OUTER HOLE) (内穴)(外穴) (INNER HOLE)(OUTER HOLE) (INTERMEDIATE HOLE) (内穴)(中穴)(外穴) (INNER HOLE) (OUTER HOLE) PARTS NO. DWG NO. SIZE サイズ PARTS NAME 部品名称 符号 部品番号 図面番号 使用個数 E10 1222764 Resin clamp NE41015-9 26.9...
Page 110
List of size for standard pipe clamp 配管固定具サイズ表 2.Tube clamp 2.管止金 2-φ5.5穴 SIZE サイズ PARTS NO. DWG NO. PARTS NAME 部品名称 符号 部品番号 図面番号 使用個数 1592425 Tube clamp 管止め金 NE31016-58 E15 0782775 Tube clamp 管止め金 NE31016-51 E16 1584215 Nylon coating tube clamp ナイロンコーティング管止め金 4P143802-51 E17 1584208 Nylon coating tube clamp ナイロンコーティング管止め金...
Page 111
Notes for ordering spare parts 部品発注の際の注意事項 1.Parts recommended to be ordered together with packing, gasket, sealing material and name plate 1.発注の際にパッキングやシール材、銘板等の同時発注を推奨する 部品 For ordering following spare parts, we recommend that you order the following packing, gasket, sealing material and name plate together at the same time. 上記のサービス扉やボックスカバーを発注の際には、下記のパッキングを同時に発注 することをおすすめします。 (1)Service door (1)サービス扉 PARTS NO. DWG NO. REMARKS PARTS NAME LXE10E- 部品名称 符号 部品番号 図面番号 備考 A18A A18B (Without cushion and sealing 1612576 Access panel ass'y サービス扉組立品...
Page 112
Notes for ordering spare parts 部品発注の際の注意事項 (3)Recorder box cover (Option) (3)レコーダボックスカバー(オプション) PARTS NO. DWG NO. PARTS NAME 部品名称 符号 部品番号 図面番号 A18A A18B 1587656 Cover (recorder) 蓋(レコーダ) 1P054302-4 1448597 Packing (recorder cover) パッキン(蓋) 4P063866-2 Name plate, レコーダボック G13 1448472 3P016113-1 recorder box ス銘板...
Page 113
Notes for ordering spare parts 部品発注の際の注意事項 2.Order for motorized valve, solenoid valve and pressure regulating valve 2.電動弁・電磁弁・圧力調整弁の発注 Refer to the following table for the name, main body, solenoid coil and ass'y of solenoid valves etc. applied to this model. この機種に使用されている電磁弁等の名称と本体・ コイル・組立品は下記のとおりです。 Common Parts QTY/UNIT 共通部品 PARTS Body/Coil DWG NO. NO.部品番 PARTS NAME 部品名称 LXE10E- 本体/コイル 符号 図面番号 号 B7-3 125649J Electronic expansion valve body ass'y 電子膨張弁本体組立品 2SA50010-2-KU 1 1 1 本体 Body...
Page 114
Notes for ordering spare parts 部品発注の際の注意事項 3.Order for pressure trasducer 3.圧力センサーの発注 Refer to the following table for the pressure transducer applied to this model. For ordering pressure transducer, we recommend that you order the following best shrinkable tube together at the same time. この機種に使用している圧力センサーは下記の通りです。 圧力センサー発注の際は、下記の熱収縮チューブを同時に発注することをおすすめし ます。 PARTS NO. DWG NO. TYPE REMARKS 呼称名 PARTS NAME 部品名称 形式 備考 符号 部品番号 図面番号 B16 1587959 High pressure tranducer 高圧圧力センサ 3P141602-1 SPCH01 B15 1587942 Low pressure tranducer 低圧圧力センサ...
Page 115
Notes for ordering spare parts 部品発注の際の注意事項 4.Order for temperature sensor 4.温度センサーの発注 Refer to the following table for temperature sensors applied to this model. この機種に使用されている温度センサーは下記の通りです。 Lot marks Type No. 表示 型番表示 Lot marks Type No. LOT 表示 型番表示 5Y01 ST9503-1- 1210 ST9701- Length Length ※Operating temp. range ー30〜+150℃ ※Operating temp. range ー30〜+70℃ 使用温度範囲 ー30〜+150℃ 使用温度範囲 ー30〜+70℃ Lot marks Type No. LOT 表示 型番表示 7828 ST9703-1 Length ※Operating temp. range ー30〜+15℃...
Page 116
Measuring and adjusting tools 測定調整用工具 1.Tools for emergency operation 1.緊急運転用工具 PARTS NO. DWG NO. ILLUSTLATION PARTS NAME 部品名称 用途 姿図 符号 部品番号 図面番号 For electronic Emergency coil エマージェンシー expansion 1080263 3P017370-1 valve コイルキャップ 電子膨張弁用 Suction modulating E m e r g e n c y エマージェンシー...
Page 117
Measuring and adjusting tools 測定調整用工具 2.Personal computer cable (for DCCS) 2.パソコンケーブル(DCCS用) The following parts are connector cables required to exchange information between the refrigeration unit and personal computer. The table below describes parts required to apply to Model LXE-C, -D, and -E new model. 下記の部品は冷凍ユニットとパソコンの情報交換に必要なコネクター、ケーブル類で す。LXE-C型、 D型、及び新機種E型対応に必要な部品を掲載しています。 [TYPE A]タイプA LXE10C LXE10C LXE10CA LXE10CA 1.5m LXE10D for MOL MOL用LXE10D (Receptacle) (レセプタクル) RS232C (Female) RS232C(メス) on the controller コントローラー側 [TYPE B]タイプB 0.3m 1.5m LXE10D LXE10D...
Page 118
Measuring and adjusting tools 測定調整用工具 Illustlation Internal Wiring 符号 姿図 内部配線 RS232C RS232C Female Female メス メス Frame Frame フレーム フレーム Daikin RS232C made Female ダイキン製 メス White Black Daikin RS232C made Female ダイキン製 メス Red 赤 White 白 Black 黒 Frame フレーム ...
Need help?
Do you have a question about the LXE10E-A18A and is the answer not in the manual?
Questions and answers