Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Wickes CDI218BW
Summary of Contents for Wickes CDI218BW
- Page 1 CORDLESS BRUSHLESS COMBI DRILL 18V LITHIUM CDI218BW 223730...
-
Page 2: Table Of Contents
CONTENTS GENERAL POWER TOOL SAFETY WARNINGS GENERAL SAFETY WARNINGS FOR BATTERY CHARGER COMPONENT LIST ACCESSORIES SYMBOLS TECHNICAL DATA NOISE INFORMATION OPERATING INSTRUCTIONS TROUBLESHOOTING MAINTENANCE ENVIRONMENTAL PROTECTION PLUG REPLACEMENT (ONLY FOR REWIRABLE PLUG OF UK & IRELAND) DECLARATION OF CONFORMITY... -
Page 3: General Power Tool Safety Warnings
ORIGINAL INSTRUCTION GENERAL POWER TOOL SAFETY WARNINGS protected supply. Use of an RCD reduces the risk of WARNING! Read all safety warnings, electric shock. instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/ 3. - Page 4 GENERAL POWER TOOL SAFETY WARNINGS repaired. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may c) Disconnect the plug from the power source and/ create a risk of injury and fire. or remove the battery pack, if detachable, from the power tool before making any adjustments, c) When battery pack is not in use, keep it away from changing accessories, or storing power tools.
- Page 5 b) Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury. c) Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.
-
Page 6: General Safety Warnings For Battery Charger
GENERAL SAFETY WARNINGS FOR BATTERY CHARGER WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. -
Page 7: Component List
COMPONENT LIST Keyless chuck Battery pack Torque adjustment ring Battery pack release button Two-speed gear control LED light Forward/Reverse rotation control On/off switch Soft grip handle Battery capacity indicator Belt clip ACCESSORIES Charger (ACG1820W1) Battery pack (ABP1820HW) Belt clip Double ended bits (PH2 / SL5.5) We recommend that you purchase your accessories from the same store that sold you the tool. -
Page 8: Symbols
SYMBOLS Li-ion battery. This product has been marked To reduce the risk of injury, read all of this with a symbol relating to ‘separate collection’ instruction manual for all battery packs and battery pack. It Li-Ion will then be recycled or dismantled in order Warning to reduce the impact on the environment. -
Page 9: Technical Data
TECHNICAL DATA Voltage No load speed 0-500/0-2000 /min Impact rate 0-8000/0-32000bpm Number of clutch positions 22+1+1 Max torque 60N.m Chuck capacity 13mm Charger Protection class Charging time 1 hr Charger Input 100-240V~50/60Hz, 55W Charger Output 2.0 A Max. drilling capacity Steel 13mm Wood... - Page 10 VIBRATION INFORMATION Vibration total values (triax vector sum) determined according to EN 62841: Vibration emission value a = 4.02 m/s² Drilling into metal Uncertainty K = 1.5 m/s² Vibration emission value a = 8.23 m/s² h,ID Impact drilling into concrete Uncertainty K = 1.5 m/s²...
-
Page 11: Operating Instructions
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. Intended Use The machine is intended for driving in and loosening screws as well as for drilling in wood, metal and plastic. BEFORE PUTTING INTO OPERATION A) CHARGING THE BATTERY a) Do not use any charger other than that specifically provided for use with the equipment. - Page 12 D) HOW TO CHARGE YOUR BATTERY PACK (See Fig. A3) CHARGING PROCEDURE 1) Plug the charger (12) into an appropriate outlet. The green LED will be lit. 2) Slide the battery pack (7) into the charger, the red LED will light to indicate charging. 3) When charging is completed, the green LED will light.
- Page 13 3. DIRECTION CONTROL (See Fig. C1, C2) Forward rotating: push the forward/reverse rotation control (4) to the right (the drill points to you). It is used for drilling and screw driving. Reverse rotation: push the forward/reverse rotation control (4) to the left (the drill points to you). It is used for remove screws or release a jammed drill bit.
- Page 14 6. TORQUE ADJUSTMENT (See Fig. F) (Screw driving force of your drill) The torque is adjusted by rotating the torque adjustment ring (2). The torque is greater when the torque adjustment ring is set on a higher setting. The torque is less when the torque adjustment ring is set on a lower setting.
-
Page 15: Troubleshooting
10. DRILLING When drilling into a hard smooth surface, use a center punch to mark the desired hole location. This will prevent the drill bit from slipping off center as the hole is started. Hold the tool firmly and place the tip of the bit at the point to be drilled. Depress the On/Off switch (10) to start the tool. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. -
Page 16: Maintenance
2. THE DRILL STOPS BEFORE THE SCREW IS COMPLETELY TIGHTENED. WHY? Verify the torque position of the torque adjusting ring (2), you can find the torque adjusting ring between the chuck and the drill body. Position 1 is the lowest torque (screw driving force) and position 22 is the highest torque (screw driving force). Position is for drill operation. Position is for hammer drill operation. -
Page 17: Plug Replacement (Only For Rewirable Plug Of Uk & Ireland)
PLUG REPLACEMENT (ONLY FOR REWIRABLE PLUG OF UK & IRELAND) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: Blue = Neutral Brown = Live As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. -
Page 18: Declaration Of Conformity
DECLARATION OF CONFORMITY Wickes Building Supplies Limited Declare that this product: CORDLESS BRUSHLESS COMBI DRILL Description and SKU code: 223730 Complies with the following Directives and Regulations: 2006/42/EC, Machinery Directive 2014/30/EU, Electromagnetic Compatibility Directive 2011/65/EU & (EU)2015/863 (RoHS),Restriction of Hazardous Substances Directive... - Page 20 Customer Helpline 0345 2005409...