Related Manuals for Demtech Pro-Tester Double-Pull
Summary of Contents for Demtech Pro-Tester Double-Pull
- Page 1 Pro-Tester Double-Pull Pro-Tester Operator’s Manual Model Number: T-0100/A Revision: C...
- Page 2 DEMTECH Services, Inc. developments. The material in the manual is for informational purposes only and is subject to change without notice. DEMTECH Services, Inc. assumes no responsibility for any errors that may appear in this manual. Printed in the USA Manual Number: T-OPERATOR’S MANUAL/PRO-TESTER, Revision: C...
-
Page 3: Table Of Contents
Rev. C, October 2020 Table of Contents SAFETY PRECAUTIONS…………………………………………………..PAGE 1 GENERAL SAFETY & MAINTENANCE INFORMATION…………….PAGE 2 Intended Use…………………………………………………………………...Page 2 Maintenance…………………………………………………………………...Page 2 GENERAL PRODUCT DATA……………………………………………...PAGE 3 SITE PREPARATION……………………………………………………….PAGE 4 UNPACKING &... -
Page 4: Safety Precautions
Rev. C, October 2020 1 Safety Precautions Safety precautions for operating personnel and equipment: WARNING 1: Operating personnel should perform only the procedures described and recommended in this manual. Only qualified service personnel familiar with electrical shock hazards and mechanical entanglement hazards present inside the equipment should perform disassembly or corrective maintenance of the equipment. -
Page 5: General Safety & Maintenance Information
Before removing or installing spare parts or performing other repair operations to the tensiometer, consult DEMTECH Services, Inc. or your authorized DEMTECH service center for advice on proper procedures. This will help insure a safe and successful outcome. Always make sure all screw connections are tight before attempting to operate the welder after maintenance and/or repair procedures. -
Page 6: General Product Data
Billet Aluminum and ground and hardened steel. DEMTECH Services, Inc. strives to make our systems easy to use and built to last. Just like all other DEMTECH Services, Inc. products, even a first-time user will be productive in minutes. With easy adjustments and a one touch operation, you will be getting test results within minutes of installation. -
Page 7: Site Preparation
Rev. C, October 2020 4 Site Preparation Before proceeding with the unpacking and installation instructions in the following section(s) make sure the work site is prepared and ready to use the Pro-Tester . You should have an adequate power source capable of providing clean Alternating Current (AC) power at 110 or 220 Volts at the rated current. -
Page 8: Unpacking And Preparation
Report any damage to the shipping carrier immediately and do not proceed with unpacking. Since the shipment is made FOB factory, you should consult your administration concerning claims for shipping damage. Please notify DEMTECH Services, Inc. immediately in writing of any shipping damage. - Page 9 Control Panel. This procedure verifies the Pro-Tester is in good working condition. If the system performs as described, you are now ready to operate the system. If the system does not perform any of the functions described above please contact DEMTECH Services, Inc. Power ON/OFF...
-
Page 10: Control Panel
Rev. C, October 2020 Control Panel The User Interface Control Panel is the main operator interface device for operating the Pro-Tester . Each component of the Control Panel is identified below (refer to Figure 5.3). Figure 5.3 Page 7 Pro-Tester Operator’s Manual... - Page 11 Rev. C, October 2020 a. Liquid Crystal Display (LCD): The LCD is a 40 Character by 4 Line display device which provides main system operation information for the Control Panel. It provides all key operating information and allows the user to input various system settings. b.
-
Page 12: Loading Samples
Rev. C, October 2020 Loading Samples Loading samples is very simple with the Pro-Tester . To load a sample open both jaws of the sample grip assemblies. The left and right grips are both screw clamps and are opened by unscrewing the tri-handle counter-clockwise (open). The sample is prepared by bending the ends to be clamped so they can be easily loaded into the grips. -
Page 13: Settings
Rev. C, October 2020 Settings a. The Pro-Tester requires various settings for proper operation. These settings are easily accessed via the Menu Mode of operation. To enter the Menu Mode, make sure the Pro-Tester is on and at the main operating screen (Refer to Page 15). Simultaneously press and hold the YES and NO buttons on the Control Panel for several seconds. - Page 14 Rev. C, October 2020 c. Weld Width (WW): The center-to-center distance between the two welds of a dual- track weld (refer to Figure 6A) or the edge-to-edge distance on a solid weld (refer to Figure 6B). It is important when measuring/calculating these distances that the operator only include the actual width of the weld.
- Page 15 Rev. C, October 2020 Figure 6A Figure 6B Figure 6C Figure 6 Pro-Tester Operator’s Manual Page 12...
-
Page 16: Factory Servicing
Carefully pack the Pro-Tester in the reusable portable shipping/storage case provided with the welder for return to DEMTECH Services, Inc.’s factory for service. Unless previous arrangements are made, shipping charges and insurance are the responsibility of the customer. Ship the packaged Pro-Tester to DEMTECH Services, Inc. -
Page 17: System Wiring Diagram
System Wire Diagram. This drawing can be very helpful in identifying and/or troubleshooting basic wiring or interconnection issues related to the Pro-Tester 9 Pro-Tester Warranty See page 17 for the DEMTECH Services, Inc. product warranty. Pro-Tester Operator’s Manual Page 14... - Page 18 Rev. C, October 2020 Figure 7.1 Page 15 Pro-Tester Operator’s Manual...
- Page 19 Rev. C, October 2020 Figure 8.1 Pro-Tester Operator’s Manual Page 16...
- Page 20 At DEMTECH Services, Inc.'s option, a service representative may be dispatched to the equipment location. As an additional protection, DEMTECH Services, Inc. warrants that for a period of 90 days from the date of shipment to the original buyer, pending prior authorization from DEMTECH Services, Inc., there will be no charge for service related shipping of parts and/or equipment or for authorized travel of a service representative to the equipment location.