Elatec TWN4 Palon Compact Quick Start Manual
  1. Manuals
  2. Brands
  3. Elatec Manuals
  4. Rfid Systems
  5. TWN4 Palon Compact
  6. Quick start manual

Elatec TWN4 Palon Compact Quick Start Manual

Transponder reader
Hide thumbs Also See for TWN4 Palon Compact:
Table of Contents

Advertisement

Quick Links

Download this manual
Transponder Reader
TWN4 Palon Compact
Quick Start Guide
Rev. 6.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TWN4 Palon Compact and is the answer not in the manual?

Questions and answers

Related Manuals for Elatec TWN4 Palon Compact

Summary of Contents for Elatec TWN4 Palon Compact

  • Page 1 Transponder Reader TWN4 Palon Compact Quick Start Guide Rev. 6.0...

  • Page 2: Getting Started

    2.2 Power Up Once a TWN4 Palon Compact reader is connected to the host, it detects the type of communications cable (USB or RS232), with which it is connected to the host.

  • Page 3: Normal Operation

    Elatec GmbH 2.3 Enumeration (USB Only) This is only applicable for the USB version: Once the device has been powered up, it is waiting for completion of the enumeration by the USB host. As long as the device is not enumerated, it is entering a minimum power consumption mode, where both LEDs are turned off.
  • Page 4 Elatec GmbH 2.6 Detection of a Transponder If a transponder is detected by the reader, following actions are performed  Send the ID to the host. By default, the USB device sends by emulating keystrokes of a keyboard. A RS232 device sends the ASCII code of an ID.
  • Page 5 Elatec GmbH 3. List of Antennas 125 kHz antenna 13.56 MHz antenna Page 5 of 12...

  • Page 6: Compliance Statements

    Elatec GmbH 4. Compliance statements (RF module) Compliance statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 7 Elatec GmbH Host devices FCC notes for a host subject to verification or SDoC: For a host device assembled with the certified module and subject to 47 CFR Part 15 verification of class A digital devices, the following statements have to be included in the user manual and the host device has to be labelled as noted below.
  • Page 8 Elatec GmbH Example for SDoC: The compliance information statement shall be included in the user's manual or as a separate sheet. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet,...
  • Page 9 Elatec GmbH NOTE: The Commission does not have a required SDoC format. This is an example only and is provided to illustrate the type of information that may be supplied with the product at the time of marketing or importation for meeting the FCC SDoC requirement.
  • Page 10 Elatec GmbH For class A devices: FCC §15.105 (b): NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 11 If additional filing is required please contact the person at ELATEC GmbH responsible for certification of the RF module. NCC Warning Statement 低功率電波輻射性電機管理辦法...

  • Page 12: Service Address

    Elatec GmbH 5. Service Address In case of any technical questions, please contact: Elatec GmbH Zeppelinstr. 1 82178 Puchheim Germany Phone: +49 (0) 89 5529961 0 Fax: +49 (0) 89 5529961 129 Email: info-rfid@elatec.com Page 12 of 12...

Table of Contents