Pittsburgh Automotive 64545 Owner's Manual & Safety Instructions

Pittsburgh Automotive 64545 Owner's Manual & Safety Instructions

Aluminum racing jack

Advertisement

Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Master Logo. Paste new logo inside text box directly after old logo and
The text box below can be copied and pasted onto pages as branding.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2018 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
carefully delete old logo to change logo throughout document.
Weight Capacity
Maximum Height
Minimum Height
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
1.5 Tons (3,000 lb.)
14-1/8"
3-1/2"
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
20e

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 64545 and is the answer not in the manual?

Questions and answers

Ron slater
March 16, 2025

Whats the middle screw between the two do not adjust screws

Summary of Contents for Pittsburgh Automotive 64545

  • Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
  • Page 2: Important Safety Information

    If it does not work properly, bleed air from its 12. Keep clear of load while lifting and lowering. hydraulic system as stated on page 4. SAVE THESE INSTRUCTIONS. Page 2 For technical questions, please call 1-888-866-5797. Item 64545...
  • Page 3: Setup - Before Use

    Saddle Pad Saddle Handle Lifting Arm Handle Socket Carry Handle Rear Caster Figure A Cover Screw for Safety Valve. Do not open or adjust. Fill Plug Figure B: Hydraulic Unit Item 64545 For technical questions, please call 1-888-866-5797. Page 3...
  • Page 4: Tool Set Up

    2. Add high grade hydraulic fluid into the Fill Plug hole slowly until the oil is 1/4″ below the fill hole. 3. Replace the Fill Plug. Page 4 For technical questions, please call 1-888-866-5797. Item 64545...
  • Page 5 3. Slowly turn the Handle counterclockwise (never more than 1/2 full turn) to lower the vehicle onto the ground. Item 64545 For technical questions, please call 1-888-866-5797. Page 5...
  • Page 6: Maintenance And Servicing

    D. Open the valve by turning the Handle children and other non-authorized people. counterclockwise and pump the Handle to bleed air from the system. E. Recheck oil level and re-fill as needed. F. Reinstall the Fill Plug. Page 6 For technical questions, please call 1-888-866-5797. Item 64545...
  • Page 7: Troubleshooting

    Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Replacement parts are not available for this item. Specify UPC 193175359599 when ordering parts. Item 64545 For technical questions, please call 1-888-866-5797. Page 7...
  • Page 8: Limited 90-Day Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents

Save PDF