Advertisement
Quick Links
Advertisement
Related Manuals for Pittsburgh Automotive 61382
Summary of Contents for Pittsburgh Automotive 61382
-
Page 2: Table Of Contents
Thoroughly test the 13. Lower load slowly. Jack for proper operation. If it does not work properly, bleed air from its hydraulic system as stated in Bleeding Instructions on page 5. Page 2 For technical questions, please call 1-888-866-5797. Item 61382... - Page 3 Cubic Feet per Minute flow ScFM at standard conditions WARNING marking concerning Risk of Respiratory Injury. Wear National pipe thread, tapered NIOSH-approved dust mask/respirator. WARNING marking concerning Risk of Explosion. SAVE THESE INSTRUcTIONS. Item 61382 For technical questions, please call 1-888-866-5797. Page 3...
- Page 4 Saddle Fill plug Fulcrum carrying Handle Jack Release Handle Valve Lever Air Lever Lock Inlet Figure A Page 4 For technical questions, please call 1-888-866-5797. Item 61382...
-
Page 5: Setup
The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. Item 61382 For technical questions, please call 1-888-866-5797. Page 5... - Page 6 Page 6 For technical questions, please call 1-888-866-5797. Item 61382...
- Page 7 Item 61382 For technical questions, please call 1-888-866-5797. Page 7...
-
Page 8: Operation
9. Once the vehicle is fully seated on the jack stands, continue slowly lowering the Jack until it is completely lowered, disconnect the air supply and store the Jack according to Maintenance Instructions on page 10. Page 8 For technical questions, please call 1-888-866-5797. Item 61382... - Page 9 Place the Air Lever Lock in its locked 6. Disconnect the air supply and store the Jack position. Then remove the jack according to Maintenance Instructions on page 10 stands from under the vehicle. Item 61382 For technical questions, please call 1-888-866-5797. Page 9...
-
Page 10: Maintenance
5. WHEN STORING, turn Release Valve counterclockwise to its open position. Store the Jack and its accessories in a clean, dry, safe location out of reach of children and other unauthorized people. Page 10 For technical questions, please call 1-888-866-5797. Item 61382... - Page 11 Jack may require bleeding - see Bleeding Instructions on page 5. Unit may have too much hydraulic fluid inside, check fluid level and adjust if needed. Follow all safety precautions whenever diagnosing or servicing the Jack. Item 61382 For technical questions, please call 1-888-866-5797. Page 11...
- Page 12 LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 12 For technical questions, please call 1-888-866-5797. Item 61382...
- Page 13 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 61382 For technical questions, please call 1-888-866-5797. Page 13...
-
Page 14: Parts List And Diagram
Fulcrum Cone Valve Packing Spring Reservoir Screw Filler Plug O-Ring Nylon Ring Screw Top Nut Air Motor O-Ring Air Hose Spring Plate Air Inlet Return Spring Jack Handle Eye Bolt Page 14 For technical questions, please call 1-888-866-5797. Item 61382... - Page 15 Assembly Diagram 32 32 35 36 37 38 39 Item 61382 For technical questions, please call 1-888-866-5797. Page 15...
-
Page 16: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the 61382 and is the answer not in the manual?
Questions and answers