Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ampler Stout 2020
Summary of Contents for Ampler Stout 2020
- Page 1 Ampler Manual Stout 2020 V2.3 03.11.20...
- Page 2 Table of Content What’s in the box? Frame number Assembly Using the Power Butt on Ampler Bikes app Maintenance Electric system support Charger safety manual Trailer adapter Specifi cations V2.3 03.11.20...
-
Page 3: What's In The Box
What’s in the box? The bike will arrive at your doorstep in a big cardboard box. Inside this you will find: • Your new Ampler bike • bike passport • 4 mm hex key • 6 mm hex key • Pedals with reflectors •... - Page 4 Assembly You will need • 4 mm hex key • 6 mm hex key • Pedals Adjust the handlebar 1. Take the 4 mm hex key and loosen the side bolts of the stem. Turn the handlebar to the riding position. Make sure the handlebar is aligned with the front wheel.
- Page 5 Assembly Insert the pedals 1. The pedals are marked with R (right) or L (left). The R pedal goes on the chainwheel side and the L pedal goes on the non-chain- wheel side. 2. Tighten the pedals with the 6 mm hex key. Pedals need to be tight so make sure you put some force into it.
- Page 6 4. Check the drivetrain. Pedal by hand and check if the chain or the belt drive runs freely. Shift the gears on the 10-speed bike. 5. Check your bike visually. Does everything seem alright? Remember to check your bike occasionally and view our Ampler Bikes Maintenance information. Adjust the seat height Take the 4 mm hex key and adjust the perfect seat height 1.
-
Page 7: Using The Power Button
To turn the lights ON and OFF, hold the power button for 1–2 seconds. You can turn the lights on/off also from your Ampler mobile app. The bike will remember the last setting, so the lights will be ON when you leave them on next time you power the bike. - Page 8 Boost Mode (assist mode 2). You can also change the support modes on the dashboard of your Ampler app. You can fully customise the assist modes with the Ampler Bikes app under ‘Vehicle settings’. bike is ON...
- Page 9 (Android 4.4 onwards) in play store. Download the app, stay close to your bike, switch on the Bluetooth, pair your smartphone with your bike and log in. The Ampler smart- phone application lets you fully customise your riding experience with the Ampler e-bike.
-
Page 10: Maintenance
• If it gets cold and icy outside, get some winter tyres. Before you buy any, make sure that they fi t the rims and frame of your Ampler e-bike. You can either get advice on this at a bike shop, where the bicycle tyres will certainly be fi tted for a small extra charge;... - Page 11 Maintenance Check the chain • Check the chain tension – if it has slackened over time (it looks saggy), get it adjusted. If you feel you are not right for the job, you can easily get it done in your local bicycle shop. •...
- Page 12 • When you fi nish cycling in the cold, make sure that the bike has time to warm up a little before you charge it. Professional maintenance Maintaining your Ampler bike is just like maintaining schedule a regular bicycle and all professional bike shops can carry out the maintenance of our bikes.
- Page 13 Re-adjusting the sensor signal helps to improve your bike’s responsi- veness and power to its original fi gures. Every Ampler has a motor controller – the so-called brain of your bike that connects all the elctronics and makes sure everything runs smoothly.
- Page 14 Now the motor and torque sensor are calibrated and assist modes are set to default, you might need to adjust them again through the app. Turn the bike on again and you are ready to use your Ampler! Firmware update Firmware update is done via the Ampler mobile app.
- Page 15 Electric system support 2. Go to Bluetooth settings 3. Find the Ampler Bike Bluetooth ID under your Bluetooth devices and click the “Info” button. Press “Forgot This Device” 4. Turn Bluetooth OFF and then back ON under settings 5. Open the Ampler app 6.
- Page 16 The charger is designed for indoor use only. Do not expose it to rain, snow or expose the device to elevated temperatures. Only use the genuine Ampler charger designated for your Ampler e-bike. Do not use this charger for other batteries. Also, do not use other battery chargers for your Ampler e-bike.
- Page 17 Do not remove the motor torque washer from the dropout – keep it attached to the axle. 2. Attach the Ampler motor axle adapter to the frame.Use a 19 mm wrench and make sure the axle adapter is securely fastened.
-
Page 18: Specifications
Specifications Sizes Medium 55 cm, Large 59 cm Parts Frame Aluminum Alloy 6061 Fork Aluminium 1 1/8”, 12 mm thru axle Crankset Alloy 42T, 170 mm Bottom Bracket Sealed BB with a torque sensor Drivetrain Shimano Deore RD-T6000 10-speed Cassette CS-HG500 11-32T Chain Shimano/ Sram compatible 10 speed chain...
Need help?
Do you have a question about the Stout 2020 and is the answer not in the manual?
Questions and answers