Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Seeburg TriSonus10 dp
Summary of Contents for Seeburg TriSonus10 dp
- Page 1 User Manual TriSonus10 dp Version 4.1 07.04.2020...
-
Page 2: Table Of Contents
TriSonus10 dp 1 Contents Contents Contents .......................... 2 Foreword .......................... 3 Safety instructions ......................4 Connectors/Indicators ....................6 Connection panel ........................6 Connectors ..........................7 Controls ........................... 8 Status indication ........................8 Operation ......................... 9 Starting up..........................9 Selecting a bank ........................9 Setting level .......................... -
Page 3: Foreword
DSP configuration of your controller, you can obtain a fresh default file from SEEBURG acoustic line and re-install the original factory pre- sets yourself. Efficient and intelligent limiter functions provide optimal protection without sacrificing any of the potential of the system. -
Page 4: Safety Instructions
TriSonus10 dp 3 Safety instructions Safety instructions Acoustic Even a low input level can result in a sound pressure level at the loudspeaker which can be damaging to your hearing. Do not remain in close proximity to the loudspeaker when it is being operated. Use hearing protection. - Page 5 TriSonus10 dp 3 Safety instructions If the loudspeaker is connected to a power source in which the volt- age is too high, a protective mechanism is triggered which reliably safeguards the amplifier module and DSP. Once triggered, the pro- tection must be renewed by a qualified service technician.
-
Page 6: Connectors/Indicators
TriSonus10 dp 4 Connectors/Indicators Connectors/Indicators 4.1 Connection panel Status indication and control panel RJ45 socket (2) PowerCon blue (3) XLR socket (1) -
Page 7: Connectors
TriSonus10 dp 4 Connectors/Indicators 4.2 Connectors XLR socket (1) The TriSonus 10 dp should be connected with a standard symmetrically wired XLR cable if the audio transmission is analogue. To connect the input signal to further devices, use the male XLR Loop thru connector. -
Page 8: Controls
TriSonus10 dp 4 Connectors/Indicators 4.3 Controls Mode button: Switch between the modes Status / Level and Presets. Set button: Set various values and Mute on/off. 4.4 Status indication Mute LED: Lights red when the system is muted (press the Set button in Status Mode), or in technically critical conditions. -
Page 9: Operation
TriSonus10 dp 5 Operation Operation 5.1 Starting up When the system is switched on, it retains the settings from the previous usage. This also applies to the Bank selection. The system is then in the Status Mode. If the red Mute LED is lit as a result of the previous setting, no signal will be passed. -
Page 10: Setting Level
TriSonus10 dp 5 Operation 5.3 Setting level After switching on and starting up, the TriSonus 10 dp is in Status Mode. Pressing the Mode button once selects the Level Mode, in which you can adjust the output volume in 3 dB steps. Seven different values between +6 dB and -12 dB are available, with 0 dB being the standard setting. -
Page 11: Preset Bank 1 - Free-Standing (Default Settings)
TriSonus10 dp 5 Operation The following representations show examples of settings: The preset “Flat” is active. The preset “Low-Boost” is active. The Soft Mode is switched on. 5.4.1 Preset Bank 1 – Free-Standing (Default Settings) This Preset Bank is to be selected when the TriSonus 10 dp is located free-standing in the room or is mounted directly next to a video display and there are no adjacent, acoustically hard reflection surfaces. -
Page 12: Preset Bank 2 - On-Wall-Mounting
TriSonus10 dp 5 Operation 5.4.2 Preset Bank 2 – On-Wall-Mounting This Preset Bank is to be selected when the TriSonus 10 dp is mounted directly on a wall. The presets are optimized in such a way that the mounting wall behind the TriSonus 10 dp is regarded as a acoustically hard reflection surface. -
Page 13: Preset Bank 3 - In-Wall-Mounting
TriSonus10 dp 5 Operation 5.4.3 Preset Bank 3 – In-Wall-Mounting This Preset Bank is to be selected when the TriSonus 10 dp is mounted directly in a wall. The pre- sets are optimized in such a way that the mounting wall besides the TriSonus 10 dp is regarded as a acoustically hard reflection surface. -
Page 14: Reprogramming Of Dp-Speakers With Preset Audio Files
3. Make sure your computer's volume is set to 100%. 4. Load the ".wav" file received from SEEBURG acoustic line into a music player. 5. Press the play button. 6. After a successful programming operation, the Mute LED turns off. -
Page 15: Technical Specifications
TriSonus10 dp 6 Technical specifications Technical specifications 2x5“ Nd (1,5“ VC) / 3x1“ Nd (1,1“ VC) Speaker Components Description Multi Media Column Amp Power LF: 280 W AES / 110-230 V HF: 175 W AES / 110-230 V Rated Current... -
Page 16: Declaration Of Conformity
DIN EN 60065 DIN EN 55103-1:1996, classes E1 to E4 DIN EN 55103-2:1996, classes E1 to E4 Declared by: Winfried Seeburg, SEEBURG acoustic line GmbH Place and date: Senden, 01.10.2019 Legally binding sign: ____________________________________________ The attachments constitute part of this declaration. This declaration certifies conformity with the listed guidelines, but does not guarantee any product characteristics. - Page 17 Benutzerhandbuch / User Manual Irrtum bei Beschreibung sowie technische Änderungen vorbehalten. Alle SEEBURG acoustic line Produkte sind nur für den gewerblichen Einsatz bestimmt. All specifications are current at the time of publishing but are subject to change. SEEBURG acoustic line...
Need help?
Do you have a question about the TriSonus10 dp and is the answer not in the manual?
Questions and answers