Seeburg A2 dp User Manual
  1. Manuals
  2. Brands
  3. Seeburg Manuals
  4. Speakers
  5. A2 dp
  6. User manual

Seeburg A2 dp User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
A2 dp
Version 3.2
18.05.2020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A2 dp and is the answer not in the manual?

Questions and answers

Related Manuals for Seeburg A2 dp

Summary of Contents for Seeburg A2 dp

  • Page 1 User Manual A2 dp Version 3.2 18.05.2020...

  • Page 2: Table Of Contents

    A2 dp 1 Contents Contents Contents .......................... 2 Foreword .......................... 3 Safety instructions ......................4 Connectors/Indicators ....................6 Connection panel ........................6 Connectors ..........................7 Controls ........................... 8 Status indication ........................8 Operation ......................... 9 Starting up..........................9 Selecting a bank ........................9 Setting level ..........................

  • Page 3: Foreword

    DSP configuration of your controller, you can obtain a fresh default file from SEEBURG acoustic line and re-install the original factory pre- sets yourself. Efficient and intelligent limiter functions provide optimal protection without sacrificing any of the potential of the system.

  • Page 4: Safety Instructions

    A2 dp 3 Safety instructions Safety instructions Acoustic Even a low input level can result in a sound pressure level at the loudspeaker which can be damaging to your hearing. Do not remain in close proximity to the loudspeaker when it is being operated. Use hearing protection.
  • Page 5 A2 dp 3 Safety instructions If the loudspeaker is connected to a power source in which the volt- age is too high, a protective mechanism is triggered which reliably safeguards the amplifier module and DSP. Once triggered, the pro- tection must be renewed by a qualified service technician.

  • Page 6: Connectors/Indicators

    A2 dp 4 Connectors/Indicators Connectors/Indicators 4.1 Connection panel XLR connectors (1) PowerCon grey (3) PowerCon blue (2)

  • Page 7: Connectors

    4.2 Connectors XLR connectors (1) The A2 dp should be connected with a standard symmetrically wired XLR cable. To connect the input signal to further devices, use the male XLR Loop thru connector. To obtain full power per- formance from the system, the signal source should be able to provide a minimum of 6 dBu distor- tion free output voltage.

  • Page 8: Controls

    A2 dp 4 Connectors/Indicators 4.3 Controls Mode button: Switch between the modes Status / Level and Presets. Set button: Set various values and Mute on/off. 4.4 Status indication Mute LED: Lights red when the system is muted (press the Set button in Status Mode), or in technically critical conditions.

  • Page 9: Operation

    A2 dp 5 Operation Operation 5.1 Starting up When the system is switched on, it retains the settings from the previous usage. This also applies to the Bank selection. The system is then in the Status Mode. If the red Mute LED is lit as a result of the previous setting, no signal will be passed.

  • Page 10: Setting Level

    5 Operation 5.3 Setting level After switching on and starting up, the A2 dp is in Status Mode. Press- ing the Mode button once selects the Level Mode, in which you can adjust the output volume in 3 dB steps. Seven different values between +6 dB and -12 dB are available, with 0 dB being the standard setting.

  • Page 11: Recalling Presets

    5 Operation 5.4 Recalling presets After switching on and starting up, the A2 dp is in Status Mode. Pressing the Mode button twice to selects the Preset Mode. Three different presets can be called up using the set button. The green LED above on the right indicates that you are in Preset Mode.

  • Page 12: Reprogramming Of Dp-Speakers With Preset Audio Files

    3. Make sure your computer's volume is set to 100%. 4. Load the ".wav" file received from SEEBURG acoustic line into a music player. 5. Press the play button. 6. After a successful programming operation, the Mute LED turns off.

  • Page 13: Technical Specifications

    A2 dp 6 Technical specifications Technical specifications 2 x 6,5" Nd (2" VC) / 1" (1,7" VC) Speaker Components Description HiMid Sound System Amp Power LF: 500 W AES / 110-230 V HF: 150 W AES / 110-230 V Rated Current...

  • Page 14: Declaration Of Conformity

     DIN EN 60065  DIN EN 55103-1:1996, classes E1 to E4  DIN EN 55103-2:1996, classes E1 to E4 Declared by: Winfried Seeburg, SEEBURG acoustic line GmbH Place and date: Senden, 01.01.2018 Legally binding sign: ____________________________________________ The attachments constitute part of this declaration. This declaration certifies conformity with the listed guidelines, but does not guarantee any product characteristics.
  • Page 15 Benutzerhandbuch / User Manual Irrtum bei Beschreibung sowie technische Änderungen vorbehalten. Alle SEEBURG acoustic line Produkte sind nur für den gewerblichen Einsatz bestimmt. All specifications are current at the time of publishing but are subject to change. SEEBURG acoustic line...

This manual is also suitable for:

00230/iii/dp

Table of Contents