EINHELL TC-TS 2025/1 UA Original Operating Instructions page 24

•
Caution! Hands and fingers may be injured on
the rotating saw blade.
•
The machine is equipped with a safety switch
to prevent it being switched on again acciden-
tally after a power failure.
•
Before you use the machine for the first time,
check that the voltage marked on the rating
plate is the same as your mains voltage.
•
If you need to use an extension cable, make
sure its conductor cross-section is big
enough for the saw's power consumption. Mi-
nimum cross-section: 1 mm
•
If you use a cable reel, the complete cable
must be pulled off the reel.
•
Check the power cable. Never use a faulty or
damaged power cable.
•
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allo-
wed to use the machine under supervision.
•
Keep your workplace clean of wood scrap
and any unnecessary objects.
•
Persons working on the machine should not
be distracted.
•
Note the direction of rotation of the motor and
saw blade.
•
After you have switched off the motor, never
slow down the saw blade by applying pressu-
re to its side.
•
Only fit blades which are well sharpened and
have no cracks or deformations.
•
Never dismantle the machine's safety devices
or render them inoperative.
•
Faulty saw blades must be replaced immedi-
ately.
•
Never use saw blades which do not comply
with the data specified in this manual.
•
It is imperative to make sure that all devices
which cover the saw blade are in good wor-
king order.
•
Warning: It is prohibited to use this saw to
make plunge cuts.
•
Damaged or faulty safety devices have to be
replaced immediately.
•
The splitter is an important safety device.
Not only does it guide the workpiece, it also
prevents the kerf closing behind the blade so
that there is no kickback from the workpiece.
Note the thickness of the splitter. The splitter
should never be thinner than the saw blade
body or thicker than the width of its kerf.
•
The guard hood has to be lowered over the
workpiece for each cut.
•
Be sure to use a push stick when slitting
narrow workpieces (smaller than 120 mm in
width).
Anl_SA_TC_TS_2025_1_UA_SPK8.indb 24 Anl_SA_TC_TS_2025_1_UA_SPK8.indb 24
GB
•
Never cut workpieces which are too small to
hold securely in your hand.
•
It is imperative for the parallel stop to be
clamped on the right-hand side of the blade
whenever you cut narrow workpieces to size.
•
Always stand to the side of the saw blade
when working with the saw.
•
Never load the machine so much that it cuts
out.
•
Always press the workpiece firmly against the
saw table.
•
. Make sure that off-cuts do not catch on the
2
saw blade crown. Risk of catapulting!
•
Refit all guards and safety devices immedia-
tely after you have completed any repairs or
maintenance work.
•
Be sure to observe the safety information
and operating and maintenance instructions
issued by the manufacturer, as well as the
dimensions listed in the Technical Data.
•
It is imperative to observe the accident pre-
vention regulations in force in your area as
well as all other generally recognized rules of
safety.
•
Note the information published by your pro-
fessional associations.
•
Connect up the dust extraction system on all
jobs. The operator has to be informed about
the conditions with an influence on dust
development, e.g. the type of material being
processed (source and collection of the dust),
the significance of local separation arrange-
ments, and the correct setting of hoods, baffle
plates and guides.
•
Operate the saw only with a suitable vacuum
extraction system or a standard industrial va-
cuum cleaner.
•
Never remove loose splinters, chips or jam-
med pieces of wood when the saw blade is
running.
•
To rectify faults or remove jammed pieces of
wood, always switch off the machine first. Pull
the power plug!
•
If the sawing gap is worn, replace the table
insert. Pull the power plug!
•
This electric tool complies with the pertinent
safety regulations.
•
Keep your work area clean and tidy. Untidy
and unlit work areas can result in accidents.
•
Keep the tool out of the rain and away from
moisture. The ingress of water into an electric
tool increases the risk of an electric shock.
•
Be careful, watch what you are doing and use
an electric tool sensibly. Do not use the tool if
you are tired or under the influence of drugs,
- 24 -
12.08.2016 08:10:35 12.08.2016 08:10:35