EINHELL TC-TS 2025/1 UA Original Operating Instructions page 23

19. Check damaged parts
– Before further use of the tool, a guard or
other part that is damaged should be care-
fully checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting,
and any other conditions that may aff ect its
operation. A guard or other part that is dama-
ged should be properly repaired or replaced
by an authorized service center unless other-
wise indicated elsewhere in this instructions
manual. Have defective switches replaced by
an authorized service center. Do not use tool
if switch does not turn it on and off .
20. Warning
– The use of any other accessory or attach-
ment other than recommended it this ope-
rating instruction or the Einhell catalog may
present a risk of personal injury.
21. Have your tool repared by an expert
– This electric appliance is in accordance with
the relevant safety rules repairing of electric
appliances may be carried out only by experts
otherwise it may cause considerable danger
for the user.
22. Connect the dust extraction device
Wherever there are facilities for fi tting a dust
extraction system, make sure it is connected
and used.
Special safety information
1. Safety actions
•
Blades that are deformed or cracked must not
be used.
•
If the table insert is worn, replace it.
•
Use only blades which are recommended by
the manufacturer and comply with EN 847-1.
When changing the blade, make sure that the
cutting width is not smaller and the saw plate
not bigger than the thickness of the splitter.
•
Make sure that the chosen blade is suitable
for the material that is to be cut.
•
If necessary, wear suitable personal protec-
tion equipment. This could consist of:
- Ear plugs to prevent the risk of damaging
your hearing;
- A breathing mask to avoid the risk of inha-
ling hazardous dust.
- Always wear gloves when handling saw
blades and rough materials. Whenever
practicable, saw blades must be carried in a
container.
Anl_SA_TC_TS_2025_1_UA_SPK8.indb 23 Anl_SA_TC_TS_2025_1_UA_SPK8.indb 23
GB
•
The following can have an influence on dust
development:
- Worn, damaged or cracked saw blades
- Recommended capacity of the vacuum ext-
raction system: 20 m/s
- Proper guidance of the workpiece
•
Blades made of high-alloy high-speed steel
(HSS) must not be used.
•
Keep the push stick or handle for a push
block at the machine at all times, even when
you are not using them.
•
When the push block is not being used, insert
it into its holder.
2. Maintenance and service
•
The following conditions can have an influ-
ence on noise impact on the operator:
- Type of sawblade (e.g. saw blades designed
to reduce noise development)
- Material of the workpiece
- The force with which the workpiece is pu-
shed against the sawblade
•
Faults on the machine or its guards, safety
devices and blade must be reported to the
person in charge as soon as they are disco-
vered.
3. Safe operation
•
Use a push stick or the handle with a push
block to feed the workpiece safely past the
saw blade.
•
Use the splitter and set it correctly.
•
Use the upper blade guard and set it to the
correct position.
•
Circular saws must not be used for slotting
jobs (cutting grooves which end in the workpi-
ece).
•
Use only blades whose permissible maximum
speed is not lower than the maximum spindle
speed of the bench-type circular saw and of
the material to be cut.
•
Use only the transport devices to move the
machine. Never use the guards for handling
or moving the machine.
•
While you are moving the machine it is best
to cover the top part of the blade, e.g. with the
guard.
•
Secure long workpieces against falling off at
the end of the cut (e.g. with a roller stand etc.)
4. Additional instructions
•
Give these safety regulations to all persons
who work on the machine.
•
Do not use this saw to cut fire wood.
•
Do not use this saw to cross-cut roundwood.
- 23 -
12.08.2016 08:10:35 12.08.2016 08:10:35