Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cyclops Lighting FR-40C
Summary of Contents for Cyclops Lighting FR-40C
- Page 1 FR-40C Warm White Super Compact, LED Fresnel USER MANUAL...
-
Page 2: Table Of Contents
Table of contents Caution! ........................3 Introduction ......................3 Safety instructions ....................3 Overview.........................4 Installation ......................4 Read ‘Safety information’ before installing the fixture..............Fastening the fixture to a flat surface ....................Mounting the fixture on a truss ......................Securing with a safety cable ....................... DMX-512 connection/connection between fixtures ................ -
Page 3: Caution
- download the latest version of the user manual from the Internet Introduction Thank you for having chosen FR-40C. You will see you acquired a powerful and versatile device. Unpack your item. Before you initial start-up, please make sure that there is no damage caused by transportation. -
Page 4: Overview
Overview Yoke Display Menu button Up button Down button Enter button PowerCon in On/Off switch Dmx out Dmx in Fuse Dimmer knob Barn door Stand feet Zoom slider Installation Read ‘Safety information’ before installing the fixture. The fixture is designed for indoor use only and must be used in a dry location with adequate ventilation. Ensure that none of the fixture’s ventilation slots are blocked. -
Page 5: Fastening The Fixture To A Flat Surface
Fastening the fixture to a flat surface The fixture can be fastened to a hard, fixed, flat surface that is oriented at any angle. Ensure that the surface and all fasteners used can support at least 10 times the weight of all fixtures and equipment to be installed on it. -
Page 6: Power Connection
Yellow/green Earth(Ground) Operation FR-40C can operate in three different modes. In each mode you can run the fixture as a stand alone fixture or in a master/slave confiugration. This next section will detail the differences in the operating modes. V1.0... -
Page 7: Addressing
In the case of FR-40C, which is 1/2/3/4 channels fixture. If you set, for example, the address in the 2 channel mode to channel 2, the device will use the channel 2 to channel 3 for control. -
Page 8: Zoom
Zoom This function allows you to adjust the beam width of the fixture. Step 1: Loosen the zoom buttons on the side of the device. Step 2: Adjust the zoom by sliding the back lenshousing forward or backward. Step 3: Tighten the zoom buttons. Control Menu Map MENU SUB MENU... -
Page 9: Dmx Protocol
DMX Protocol 1 Channel Mode Function Function Control 000-255: 0-100% dimmer Dimmer 2 Channels Mode Function Function Control Dimmer 000-255: 0-100% dimmer Strobe 000-255: strobe with speed increasing 3 Channels Mode Function Function Control Dimmer 000-255: 0-100% dimmer Strobe 000-255: strobe with speed increasing 000-255: Dimmer speed 0 (no delay) 000-255: Dimmer speed 1 Dimmer mode... -
Page 10: Fixture Cleaning
4 Channels Mode Function Function Control 000-009: ID1-ID66 010-019: ID1 020-029: ID2 030-039: ID3 040-049: ID4 050-059: ID5 060-069: ID6 070-079: ID7 080-089: ID8 090-099: ID9 ID setting 100-109: ID10 110-119: ID11 120-129: ID12 130-139: ID13 140-149: ID14 150-159: ID15 160-169: ID16 170-179: ID17 180-189: ID18... -
Page 11: Troubleshooting
Check the connection of power and main fuse. Be sure the external fuse has not blown. • Measure the mains voltage on the main connector Technical specifications Model FR-40C 40 watts Cool white COB LED Light source: LED Color temperature: 5600K LED life expectancy: 50,000 Hrs. - Page 12 Please note: All information is subject to change without prior notice. 20.06.2018 306MM 211MM 156MM 230MM www.cyclopslighting.com V1.0...
Need help?
Do you have a question about the FR-40C and is the answer not in the manual?
Questions and answers