Table of contents Caution! �������������������������������������������������������������������������������������������������������������������3 Introduction ������������������������������������������������������������������������������������������������������������3 Safety instructions ��������������������������������������������������������������������������������������������������3 Fxiture overview �����������������������������������������������������������������������������������������������������3 Installation ��������������������������������������������������������������������������������������������������������������4 Read ‘Safety information’ before installing the fixture ��������������������������������������������������������������������������� 4 Fastening the fixture to a flat surface ���������������������������������������������������������������������������������������������������� 4 Mounting the fixture on a truss �������������������������������������������������������������������������������������������������������������� 4 Securing with a safety cable ������������������������������������������������������������������������������������������������������������������...
- download the latest version of the user manual from the Internet Introduction Thank you for having chosen LEDE 300S. You will see you acquired a powerful and versatile device. Unpack your item. Before you initial start-up, please make sure that there is no damage caused by transportation.
3-pin DMX input socket 3-pin DMX output socket Powercon in Fuse 14 15 16 The head should be locked for transportation- the tilt lock latch (3) and the pan lock latch (4) have to be in the locked positions. To unlock the head, move these latches to unlock positions before operating the fixture. 5V micro USB port enable user to adjust fixtures' DMX address without connecting to the main power.
Connection with the mains: The LEDE 300S is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC power source from 100-240 Volts. This fixture must be earthed. To use the fixture, a plug must be fixed.
In the case of the LEDE 300S, which is 20/25 channels fixture. If you set, for example, the address in the 20 channel mode to channel 21, the device will use the channel 21 to 41 for control.
2. Select the Fixture Set tab. 3. Press Up or Down button and select Run Mode and select Host. 4. The fixture will run internal programs. Master-Slave Operation This function will allow you to link up to 16 units together and operate without a controller. In a Master- Slave set up one unit will act as the controlling unit and the others will react to the controlling units programs.
Language Language, English Close Display Flip Display Reverse 180° Display Open Show Display blacklight, always on Display Mode Display blacklight, 60 seconds Cancel XY Reset Pan Tilt reset Cancel Moto Reset Motos reset Reset Cancel All reset Reset all Cancel Factory Factory default Current Time...
Page 9
Tilt 000-255 Tilt movement by 270° Tilt fine 000-255 Fine control of tilt movement Pan/Tilt speed 000-255 Pan/Tilt speed, decreasing Marco Function 000-129 No function 130-150 Pan/Tilt reset 151-159 No function 160-180 Effect reset 181-189 No function 190-210 All reset 211-255 No function Strobe...
Page 10
070-079 Gobo 7 080-089 Gobo 8 090-112 Backwards rotation from fast to slow 113-120 Stop Forwards rotation from slow to fast 121-143 Shaking gobos from slow to fast 144-157 Gobo 1 158-171 Gobo 2 172-185 Gobo 3 186-199 Gobo 4 200-213 Gobo 5 214-227...
Rot. gobo indexing and rotation Gobo indexing 0-63 Gobo indexing 64-126 Forwards rotation from fast to slow 127-128 Stop Backwards rotation from slow to fast 129-191 192-193 Stop 194-255 Forwards and backwards rotation from slow to fast Rot. gobo - fine 0-255 Fine indexing (rotation) Prism...
Fuse Replacement This fuse is located in a fuseholder next to the MAINS OUT socket on the connections panel. To replace a fuse: 1. Disconnect the fixture from power and allow it to cool for at least 10 minutes. 2. Unscrew the cap of the fuseholder and remove the fuse. Replace with a fuse of the same size and rating only.
Specifications Model LEDE 300S Light source: 300 watts white LED LED life expectancy: 50,000 Hrs� Color temperature: 6600K CRI 70 Beam angle: 13° to 44° Light output: 60,000 Lux @ 2m @ 13° Electronic focus Dimmer: Linear adjustment Color wheel:...
Need help?
Do you have a question about the LEDE 300S and is the answer not in the manual?
Questions and answers