Dual- Zone Piezo Sen Sor; Smart Trunk Re Lease Op Tion; Timer Op Tions - Clifford Tazor 4 Owner's Manual

Dei clifford tazor 4 car alarms: user guide

Installation manual (27 pages)

Table of Contents

The Dual-Zone Piezo Sensor detects theft-related vibrations/ impacts and triggers the alarm. It also has a warning zone that detects less serious occurrences

—such as someone bumping your car door with their's—and sounds a brief warning tone. If needed, sensitivity of this sensor can be readjusted by any

Authorized Clifford Dealer (preferably your installing dealer). To prevent falsing, system sensors are bypassed when the engine is remotely started (if you

have the IntelliStart 4 option). Ask your Authorized Clifford Dealer about these optional sensors that will further enhance the security of your vehicle:

Glass Tampering Sensor:

impact sensor to detect. The Glass Tampering Sensor detects the sound of glass breaking, and glass tampering attempts, and will trigger the alarm.

Digital Tilt/Motion Sensor:

conditions that falsely set off all other sensors. Even if you park on a hill, the Digital Tilt/Motion Sensor will accurately respond to the first hint of

tampering to reliably protect your wheels and entire vehicle.

If you have this option, you may use the

of the remote trunk release when you drive, or when the system is armed. The Smart Trunk Release feature requires installer programming, so if you have

the optional trunk release installed, you may want to verify that it will NOT activate when the system is armed. If it can be activated while armed, causing the

alarm to sound, please return to your installing Clifford Dealer and have them correct this (it only takes a couple minutes and there will be no charge to you).

The system's built-in electronic timer can be optionally wired to provide one of several different functions. Timer duration settings can be made by your

installing Clifford Dealer or by you via the CliffNet Wizard. Ask your Authorized Clifford Dealer for further details:

The timer can be wired to provide remote controlled headlight activation for any duration you wish between 1 second and 4 minutes, allowing you to

remotely light your way to and from the vehicle by pressing the

The timer can automatically close the windows upon remote arming on vehicles with an "all-close" feature that raises them if the key is held in the driver's

door (a common feature on several European vehicle models).

NOTE: Although this timer circuit could be wired to control power windows on non-European cars that do not have

this key-in-the-door "all-close" feature, Clifford Electronics strongly recommends against this. If so wired, the timer

would force the window motors to "shut" the windows even if they were already closed. This places excessive strain

on the vehicle's window motors, causing overheating, premature failure and even the possibility of fire. As such, if

you cannot close the windows of your vehicle by turning and holding the key in the driver's door, do not permit the

system's timer circuit to be wired to automatically close the windows.

If your car does not have an all-close feature, one or more SmartWindows 4 accessories are needed. One SmartWindows 4 module can control two power

windows. In addition to automatically closing the power windows every time you arm, SmartWindows 4 also allows you to remotely roll down the

windows after disarming and to remotely vent them open slightly for ventilation on hot days. Inside the car, SmartWindows 4 also provides one-touch full

open, one-touch full close and one-touch stop to each of your factory window control switches.

Win dow AutoClose In stant By pass

If you have the timer-based window closure option noted above, you may choose to arm without automatically closing the windows. This is handy on hot

days by allowing you to leave one or more windows slightly open while the system remains armed. To do so, simply turn the ignition switch to "ON" and

then "OFF" rapidly. You will hear a chirp confirmation (this action also activates Instant AutoArming bypass prevously noted). When you then exit and

arm, the system will not close the windows. Normal autoclose operation is restored the next time you arm.

Vehicles that have turbocharged engines often require a cool-down period of one to several minutes after driving, particularly high-rev driving. Until now,

drivers of such vehicles had two choices: sit in the car after parking and wait several minutes to turn off the engine, or have an expensive turbo timer

accessory added that would often interfere with car alarm operation. But with the addition of an optional relay, your system's timer output can save you

money and make turbo cool-down easy and convenient. If you have this option installed, just press the assigned button or button combination(your

Clifford installer will have told you which he has assigned to this function) on the remote control before shutting off the engine. Then remove your car

key (the engine will continue running), exit, and press the

will continue to idle the engine for any duration you choose up to 4 minutes. To ensure against any possibility of false alarms, the system will keep the

sensors offline while the engine is idling, then automatically bring them back online right after the engine is shut down.

If power is removed, SmartPowerUp 2 ensures the system automatically restores itself to its previous state when power is restored. So if a thief disconnects

the power and then restores it in an attempt to start the car, the system will re-arm and instantly sound the siren while continuing to immobilize the

starter. If your vehicle is to be serviced by a mechanic, just put the system in valet mode. If the mechanic needs to interrupt power, your system will

automatically return to its valet mode state when power is restored; there will be no alarm activation.