Night Vision; Smart Autotesting - Clifford Concept 600 Owner's Manual

All of the following NightVision Headlight Automation features are built into your Concept 600:
n
You may turn the NightVision features on or off whenever you wish (see User-selectable features).
n
n
n
about the same time as the public street lights turn on. If you find that your vehicle's headlights come on significantly earlier or later than the street
lights, you may change NightVision's headlight activation threshold. See the User-selectable features (column 3, row 7) to change the threshold. To
set the headlights to turn on when it is darker, select the "darker" setting, to have them turn on when it is lighter, select the "lighter" setting. The
CliffNet Wizard software provides even greater incremental activation threshold control.
n
when the car's engine is started, NightVision instantly turns on the headlights. When the vehicle is briefly driven under an overpass in daylight, the
headlights will not turn on. Even more importantly, when passing through a brightly lit area at night, the headlights will not switch off. However, if
you drive into a dark parking structure during the day, NightVision will turn on the headlights within five seconds of entering the structure.
n
10 sec.; see User-selectable features column 3, row 5) after you turn off the engine to light your path away from the vehicle. If you don't care for this
feature, you may use the User-selectable features programming (column 3, row 6) to select all NightVision features except post-parking illumination.
n
for any duration you select between 1 sec. and 4 min. (factory preset to 10 sec.; to change the duration, see User-selectable features column 3, row 5).
n
When you turn on the windshield wipers NightVision automatically turn on the headlights to increase your vehicle's visibility to all
other drivers on the road. This is also a great battery-saving feature since you don't need to remember to turn off the headlights after driving in the
rain during daylight hours. If using intermittent wipers, just measure the maximum amount of time between wiper activations, add a second, then
program the Headlight Duration (feature column 3, row 5) for that amount of time using the User-selectable features.
n
If you opted to have the Clifford DataPort interface connector installed with your system, you can use our CliffNet Wizard software to access your system
through your Windows PC. CliffNet Wizard will show you, on your PC screen, all your user-programmable feature settings. You can change settings
simply by mouse-clicking the graphical button for each feature. You can customize features, add or delete remote controls, change remote control button
assignments, view a chronological history of trigger and sensor activations, and much more. It's actually fun! And secure. To learn more and download
this free software, go to www.clifford.com/wizard.
Each time you remotely arm the system, it tests all triggers and sensors. If the hood or trunk is open, the system will immediately sound 4 chirps and 4
indicator light flashes instead of the usual 2 and 2. If a door is ajar, you'll receive 2 chirps and 2 flashes, then, 5 seconds later, there will be 4 chirps and 4
flashes. If a sensor is malfunctioning, you will receive the usual 2 chirps and 2 flashes, then, 10 seconds later, there will be 4 chirps and 4 flashes.
NOTE: Since this is a warning indication, you will hear the 4 chirps even if you use the chirp muting feature.
n
4-chirp/4-flash signal upon arming, perform the following to identify the malfunctioning trigger or sensor:
1. Remotely disarm, then turn on the ignition. The LED status indicator inside your vehicle will be flashing, pause, then repeat.
2. Count the number of flashes in one cycle between pauses (for your convenience, the flash cycle repeats a total of 5 times) and refer to the chart below:
LED flashes
The system automatically turns on the headlights.
The system automatically turns off the headlights.
The NightVision electronics have a preset threshold that automatically turns on the headlights at
The NightVision electronics automatically turn the headlights on or off only when necessary. For instance, if it is dark
NightVision keep the headlights on for any post-parking duration between one second and 4 minutes (factory preset to
Pressing button 4 on your master remote or button
If you wish to manually turn on the headlights, simply turn on your vehicle's headlight switch.
Optional CliffNet Wizard™ & DataPort Interface Connector
The system can also indicate the specific trigger or sensor that is malfunctioning. If you get the
NightVision™

Smart AutoTesting™

Meaning
(companion remote) will activate the headlights