Mitsubishi Electric Mr.SLIM PUZ-ZM200YKA Service Manual page 81

(2) Functions available when setting the unit number to 01–03 or AL (07 in case of wireless remote controller)
• When setting functions for an indoor unit in an independent system, set the unit number to 01 referring to 4 setting the
indoor unit number of Operating Procedure.
• When setting functions for a simultaneous- Twin Triple indoor unit system, set the unit number to 01 to 03 for each indoor
unit in case of selecting different functions for each unit referring to 4 setting the indoor unit number of Operating Procedure.
• When setting the same functions for an entire simultaneous Twin Triple-indoor unit system, set refrigerant address to AL (07
in case of wireless remote controller) referring to 4 setting the indoor unit number of Operating Procedure.
Function
Filter sign
100 h
2500 h
No filter sign indicator
Airflow Quiet
(Fan speed)
Standard
High ceiling
No. of air outlets 4 directions
3 directions
2 directions
Optional high efficiency Not supported
filter
Supported
Vane setting
No vanes (Vane No. 3 setting: PLA only)
Vane No.1 setting
Vane No.2 setting
3D i-See sensor
Position 1 ("□" stamp position)
positioning
(Position 2)
Position 3 ("□" stamp position)
Optional humidifier Not supported
(PLA only)
Supported
Vane differential setting in No.1 setting (TH5: 24–28:)
heating mode
No.2 setting (Standard, TH5: 28–32:)
(cold wind prevention)
No.3 setting (TH5: 32–38:)
Swing Not available
Available
Set temperature in heating
Available
mode (4 degree-up)*
Not available
Fan speed during the
Extra low
heating thermo-OFF
Stop
Setting fan speed
3D i-See sensor ceiling Low ceiling
height setting
Standard
High ceiling
Fan speed during the Setting fan speed
cooling thermo-OFF
Stop
Extra low
Detection of abnormality of Available
the pipe temperature (P8)
Not available
*PKA-HAL/KAL: 2 degree-up
PEAD-M JA(L)
•
Function
Filter sign 100h
2500h
No filter sign indicator
External static pressure 35/50/70/100/150Pa
External static pressure 35/50/70/100/150Pa
Set temperature in heating Available
mode ( 4 degree-up )
Not available
Fan speed during the Extra low
heating thermo OFF
Stop
Set fan speed
Fan speed during the
Set fan speed
cooling thermo OFF Stop
Detection of abnormality Available
of the pipe Not available
Mode No.11
Setting No. Settings
Vane No.3 setting
1
No Vanes
2 Vane No.1 setting
3 Vane No.2 setting
* In this setting, the ceiling may be smudged.
OCH738
Mode Setting
Settings
No. No.
1
07 2
3
1
08 2
3
1
09 2
3
1
10
2
1
11 2
3
1
12 2
3
1
13
2
1
14 2
3
}
Swing 1
PLA-EA 23
Wave airflow 2
1
24
2
1
25 2
3
1
26 2
3
1
27 2
3
1
28
2
Setting
Mode
Settings
No. No.
1
07 2
3
Refer to the right table
08
Refer to the right table
10
1
24
2
1
25
2
3
1
27
2
1
28
2
PLA-ZM ・ EA
Less smudging
( Downward position than the standard )
Standard
Less draft * (Upward position than the standard) Less draft * (Upward position than the standard)
81
Initial setting (factory setting)
4-way cassette Ceiling suspended
PLA-ZM•EA PCA-HAQ
●
●
–
● –
–
● –
–
–
● –
–
–
–
● –
–
–
● –
● –
– –
–
● –
–
● –
● ●
● ●
–
● –
–
●
● –
● ●
: Initial setting
External static
( Factory setting ) pressure
35Pa
50Pa
70Pa
100Pa
150Pa
No vane function
Standard
─: Not available
Wall mounted
PCA-M•KA PKA-M•HA(L) PKA-M•KA(L)
●
●
–
● ●
–
– –
– –
– –
● –
–
–
● –
–
– –
– –
– –
– –
– –
● ●
● ●
● ●
● ●
– –
– –
– –
– –
● ●
● ●
Setting No. Initial setting
( Factory setting )
Mode No. 08 Mode No. 10
2 1
1
3
2
1
2 2
3 2
PCA-M ・ KA
●
●
–
–
–
–
–
–
–
–
–
–
–
–
–
–
●
●
●
●
–
–
–
–
●
●