SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
Old hose sets must not be reused. • If the mains power supply cable is damaged, it must be • replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. Before any maintenance operation, deactivate the appliance •...
• Do not put flammable products or items that are DISPOSAL wet with flammable products in, near or on the WARNING! Risk of injury or appliance. suffocation. • Make sure that all metal objects are removed from the laundry. • Disconnect the appliance from the mains •...
PROGRAMME CHART Maximum load Programme Programme description Maximum spin Temperature range (Type of load and soil level) speed 30'@30° 3 kg A short cycle for synthetic and delicate items with 30°C 800 rpm light soil level or for items to freshen up. Cottons 10 kg White cotton and coloured cotton.
Approximate Energy con- Water con- Remaining programme Programmes Load (kg) sumption sumption (li- duration (mi- moisture (%) (kWh) tre) nutes) Cottons 40°C 1,40 Synthetics 40°C 0,80 Delicates 40°C 0,56 Wool/Handwash 0,42 30°C Standard cotton programmes Standard 60°C cot- 1,02 Standard 60°C cot- 0,75 Standard 40°C cot- 0,67...
The related indicator comes on. To drain the water refer to ‘At the end of the programme’. DRAIN & SPIN With this option you can perform the spin and drain QUICK cycle. With this option you can decrease the programme The spin phase is suitable to the washing duration.
BEFORE FIRST USE 1. Put a small quantity of detergent in the This removes all possible dirt from the drum and the compartment for washing phase. tub. 2. Set and start a programme for cotton at the highest temperature without laundry. DAILY USE DETERGENT COMPARTMENTS WARNING! Refer to Safety chapters.
STARTING A PROGRAMME WITHOUT THE 2. Adjust the flap in posi- tion B. FINISH IN OPTION 3. Put back the drawer in Touch the button the recess. • The indicator of the button stops to flash and stays on. • The programme starts, the door locks, the indicator is on.
• Keep the door and the detergent drawer ajar, to 1. Touch prevent the mildew and odours. The indicator of this button flashes. The washing programme is completed, but 2. Change the options. If you change any option there is water in the drum: the Finish In option (if set) will be disabled.
HINTS AND TIPS THE LAUNDRY LOAD – powder detergents for all types of fabric, – powder detergents for delicate fabrics (40 • Divide the laundry in: white, coloured, °C max) and woollens, synthetics, delicates and wool. – liquid detergents, preferably for low •...
• Select the cotton programme with the highest Regularly examine the drum to prevent limescale temperature with a small quantity of detergent. and rust particles. To remove rust particles use only special products DOOR SEAL for washing machines. Do this separately from the Regularly examine the laundry wash.
3. Remove the drain hose from the rear support 5. When no more water flows, install the inlet and unhook it from sink or spigot. hose and the drain hose again. 4. Put the ends of the drain and inlet hose in a WARNING! Make sure that the container.
POSSIBLE FAILURES Problem Possible solution The programme does not • Make sure that the mains plug is connected to the mains socket. start. • Make sure that the appliance door is closed. • Make sure that there is not a damaged fuse in the fuse box. •...
Problem Possible solution The appliance fills with wa- • Make sure that the drain hose is in the correct position. The end of ter and drain immediately. the hose may be too low. Refer to 'Installation instruction'. The cycle is shorter than •...
Spin Speed Maximum 1400 rpm 1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your do- mestic cold water storage system.