Crown XTi 1002 Specifications page 2

PERFORMANCE
Sensitivity (for full rated power at 4 ohms):
1.4 Vrms
Frequency Response
(at 1 watt, 20 Hz to 20 kHz): +0 dB, –1 dB
Signal-to-Noise Ratio (below rated 1kHz
power at 8 ohms):
XTi 1002/2002/4002: 100 dB (A weighted),
XTi 6002: 103 dB (A weighted)
Total Harmonic Distortion (THD): < 0.5%
Damping Factor 20 Hz to 1 kHz: > 500
Crosstalk (below rated power):
20 Hz - 1 kHz: > 70 dB
Input Impedance (nominal):
20k ohms balanced, 10k ohms unbalanced
Maximum Input Signal: +22 dBu typical
AC Line Voltage and Frequency Configurations:
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
AC Line Current (120 VAC amplifier playing
1/8 power pink noise into 4 ohms per ch):
XTi 1002: 6.8A; no more than 38W at idle,
XTi 2002: 8.3A; no more than 38W at idle,
XTi 4002: 10.5A; no more than 38W at idle,
XTi 6002: 15.3A; no more than 180W at idle
Operating Temperature:
o o
0 C to 40 C at 95% relative humidity
(non-condensing)
INDICATORS
Signal Indicator: Green LED, one per channel,
illuminates when a very low-level signal
is present at input (may be used for
troubleshooting cable runs).
–10 Indicator: Green LED flashes when output
signal exceeds –10 dB below clip.
–20 Indicator: Green LED flashes when output
signal level exceeds –20 dB below clip.
Ready Indicator: Green LED, one per channel,
illuminates when the amplifier is ready to
produce audio.
Clip Indicator: Red LED, one per channel, turns on
at the threshold of audible distortion.
Temp Indicator: Red LED, one per
channel, illuminates under excessive
temperature conditions.
Power Indicator: Blue LED illuminates when the
amplifier has been turned on and has power.
Specifications subject to change without prior notice. Latest information available at CrownAudio.com.
Crown and Crown Audio are registered trademarks of Crown International. Other trademarks are the property of their
respective owners. Printed in U.S.A.
© 2010 Crown Audio, Inc.
CONTROLS
Level: Two front-panel rotary level controls,
one for each channel.
Power Switch: On/Off switch applies AC power
to the amplifier.
Sel/Prev/Next Buttons: Three buttons near the
LCD screen that are used to access menu
items and front panel lockout.
LCD Screen: Backlit liquid crystal display that
shows preset and processing status.
INTEGRATED PROCESSING
Input EQ: 6 parametric filters per channel
with adjustable Q, ±15 dB boost/cut. Also
adjustable high and low shelving filters. This
8-filter EQ section can be bypassed.
Crossover Filters: Highpass and Lowpass per
channel. Butterworth 6/12/18/24 dB per
octave. Linkwitz-Riley 24/48 dB per Octave.
Also includes ± 15 dB bandpass gain and
polarity control.
Output EQ: 8 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. This 8-filter
EQ section can be bypassed.
Delay: For signal alignment of driver;
50 ms of total delay.
SubHarmonic Synth: Takes the low-frequency
content of the input signal and "synthesizes"
a new signal that is the same as the input
signal but one octave lower. The new
synthesized signal is then mixed with the
original signal to create the effect. New:
Users now have control over frequency, gain,
and filter type.
Peak Plus Limiter: User defeatable limiter
™
x
that allows users to control Threshold,
Attack, and Release times.
Presets: 30 total presets, 29 of which
are user-definable.
Crown International
1718 W. Mishawaka Rd.
Elkhart, IN 46517-9439
TEL: 574-294-8200
FAX: 574-294-8FAX
CrownAudio.com
INPUT/OUTPUT CONNECTORS
Input Connectors: XLR, one per channel)
Link/Out Connector: Loop-thru signal from input
connector for linking another amplifier, one
per channel.
Output Connectors: Two Neutrik
Speakon
®
NL4MP output connectors. Channel-1 Speakon
is wired with Ch. 1 and Ch. 2 outputs for use
with optional single 4-conductor cable. Two
binding post outputs (in parallel with Speakon
connectors).
HiQnet USB Connector: Type B, connects to
™
HiQnet™ network.
CONSTRUCTION
Chassis: Steel
Front Panel: Cast-aluminum
Cooling: Proportional speed fan with
front-to-rear airflow.
Dimensions:
XTi 1002/2002/4002: 19" (W) x 3.5" (H)
x 12.25" (D),
XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D)
Net Weight:
XTi 1002/2002/4002: 18.5 lbs (8.4kg),
XTi 6002: 24.0 lbs (10.9kg)
Shipping Weight:
XTi 1002/2002/4002: 21.5 lbs (9.8kg),
XTi 6002: 30.0 lbs (13.6kg)
®
®
®