Wiring Connections; Main Harness (H1), 12-Pin Connector; H2 Harness, 18-Pin Connector; Remote Start, (H3) 10-Pin Connector - Directed Electronics Viper 5901 Installation Manual

Wiring Connections

jumper settings

Main Harness (H1), 12-pin connector

TACH threshold OFF:
TACH threshold ON:
RED/WHITE
H1/1
H1/2 RED
IMPORTANT! Neutral Safety
H1/3 BROWN switch must be plugged in
and in the ON position
H1/4 WHITE/BROWN
H1/5 BLACK
H1/6 VIOLET
H1/7 BLUE
H1/8 GREEN
H1/9 BLACK/WHITE
H1/10 WHITE/BLUE
H1/11 WHITE
ORANGE
H1/12
*The Normally Closed setting will only work if one of the vehicle's doors is connected. If more than one door
is to be monitored, then it is recommended to use the Xpresskit DTIMAZDA or tech tip # 1921 on www.direct-
echs.com to interface with these types of vehicles.

H2 Harness, 18-pin connector

LIGHT GREEN/BLACK
H2/1
H2/2 ORANGE/BLACK
H2/3 GREEN/WHITE
H2/4 VIOLET/BLACK
H2/5 WHITE/BLACK
H2/6 WHITE/VIOLET
H2/7 GREY/BLACK
H2/8 BROWN/BLACK
H2/9 VIOLET/WHITE
TACH threshold OFF:
H2/10 DARK BLUE
TACH threshold ON:
H2/11 PINK/WHITE
H2/12 ORANGE
H2/13 PURPLE
Bitwriter
Port
H2/14 PINK
H2/15 GREY
H2/16 BLUE/WHITE
H2/17 BROWN
H2/18 BLACK/WHITE

Remote Start, (H3) 10-pin connector

H3/1 PINK
H3/2
RED/WHITE
H3/3 ORANGE
H3/4 VIOLET
H3/5 GREEN
6
(for external
10A FUSE
MINI ATM
Xpresskit
Bitwriter
RPN: 8540
interface
Port
module)
To change
(-) 200mA AUX/TRUNK OUTPUT
(+)12VDC CONSTANT INPUT
(+) SIREN OUTPUT
PARKING LIGHT ISOLATION WIRE - PIN 87a of onboard relay
(-) CHASSIS GROUND
(+) DOOR TRIGGER INPUT
(-) TRUNK PIN/ INSTANT TRIGGER INPUT (N/C OR N/O)
(-) DOOR TRIGGER INPUT (N/C* OR N/O)
(-) 200mA DOME LIGHT SUPERVISION OUTPUT
(-) REMOTE START/ TURBO TIMER ACTIVATION INPUT
1
PARKING LIGHT OUTPUT
1
(-) 500mA GROUND WHEN ARMED OUTPUT
1
1
1 3
18
9
(-) 200mA OEM ALARM DISARM OUTPUT
(-) 200mA AUX 4 OUTPUT
(-) 200mA OEM ALARM ARM OUTPUT
(-) 200mA AUX 2 OUTPUT
(-) 200mA AUX 3 OUTPUT
(-) 200mA AUX 1 OUTPUT
(-) DIESEL WAIT TO START INPUT
(-) 200mA HORN HONK OUTPUT
TACHOMETER INPUT
To change
(-) 200mA STATUS OUTPUT
jumper
settings
(-) 200mA FLEX RELAY CONTROL OUTPUT
(-) 200mA ACCESSORY OUTPUT
(-) 200mA STARTER OUTPUT
Neutral Safety Remote
Switch Start In
(-) 200mA IGNITION 1 OUTPUT
(-) HOOD PIN INPUT (N/C OR N/O)
(-) 200mA 2ND STATUS /REAR DEFOGGER OUTPUT
(+) BRAKE SHUTDOWN INPUT
(-) NEUTRAL SAFETY INPUT
1 12
1 10
(+) IGNITION 1 INPUT/OUTPUT
1 8
(87) FLEX RELAY +12V INPUT (30A FUSED)
1 (+) ACCESSORY OUTPUT 5
(+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL)
1 3
(+) STARTER INPUT (KEY SIDE OF THE STARTER KILL)
Neutral Safety Remote
Switch Start In
1 12
1 10
Bitwriter
Port
1 8
Neutral Safety
ON
Switch
1 5
1 3
10 9 8
12
5 4 3
10
8
5
10
1
Door Lock/ H2 Relay Out
Unlock Output Port
10 9 8 7 6
5 4 3 2 1
1
Door Lock/ H2 Relay Out
Unlock Output Port
CPU1
10 9 8 7 6
5 4 3 2 1
Valet
Port
1
7 6
2 1
1 12
CPU1
NOTE: Pin 1 is on the left
Valet Status
Port Port LED
12
© 2009 Directed Electronics. All rights reserved.
Valet Status
Port Port LED
Optional Mux P
(for additional se
Status
LED
12
R
4 3
ELECTRONICS 2 1
TACH LEARN THREASHOLD
JMP1 OFF ON
ELECTRON