Table of Contents
Advertisement
Responder HD Models
Viper 5902
Clifford 590.2X
Python 592
Security and Remote Start
Installation Guide
This product is intended for installation by a professional
installer only! Attempts to install this product by a per-
son other than a trained professional may result in severe
damage to a vehicle's electrical system and components.
© 2009 Directed Electronics, Vista, CA
N5902 2009-09b
Advertisement
Table of Contents
Related Manuals for Directed Electronics Viper 5902
Summary of Contents for Directed Electronics Viper 5902
- Page 1 This product is intended for installation by a professional installer only! Attempts to install this product by a per- son other than a trained professional may result in severe damage to a vehicle’s electrical system and components. © 2009 Directed Electronics, Vista, CA N5902 2009-09b...
- Page 2 Safe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nui- sance Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics. The Bitwriter (p/n 998U) ® requires chip version 2.7 or newer to program this unit.
-
Page 3: Table Of Contents
Contents Warning! safety first ........................4 Wiring Diagram ..........................5 Wiring Connections ........................6 Main Harness (H1), 12-pin connector ..................6 H2 Harness, 18-pin connector ....................6 Remote Start, (H3) 10-pin connector .................... 6 Door Lock, 3-pin connector ......................7 Adjusting the Sensor ........................ -
Page 4: Warning! Safety First
This testing should be performed by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. -
Page 5: Wiring Diagram
RF Port and in the ON position Switch for IVU Bitwriter Port Control Center Temperature Sensor D2D Port (for external Door Lock Xpresskit interface module) (see wiring tables) H2 Harness (see wiring tables) © 2009 Directed Electronics. All rights reserved. -
Page 6: Wiring Connections
(+) IGNITION 1 INPUT/OUTPUT H3/2 RED/WHITE (87) FLEX RELAY +12V INPUT (30A FUSED) H3/3 ORANGE (+) ACCESSORY OUTPUT ELECTRONICS H3/4 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL) TACH LEARN THREASHOLD JMP1 OFF © 2009 Directed Electronics. All rights reserved. -
Page 7: Door Lock, 3-Pin Connector
Pressing this button increases the sensitivity one level. The siren chirps twice confirming the sensitivity adjustment. • button: Pressing this button decreases the sensitivity one level. The siren chirps once confirming the sensitivity adjustment. © 2009 Directed Electronics. All rights reserved. -
Page 8: Initializing Virtual Tach (Not Needed W/Hardwire Tach Inputs)
Turn the key to the “run” position, this releases the shifter. Place the car in drive (D). Place your foot directly over the brake pedal, but do not depress it. Be ready to step on the brake if the starter engages. © 2009 Directed Electronics. All rights reserved. -
Page 9: Remote Start Shutdown/Startup Diagnostics
If the vehicle is not a General Motors product or a Dodge Dakota pickup, please call Directed Electronics Technical Support for an alternative shut-down method. Do not return the vehicle to the customer until this feature is properly installed! -
Page 10: Remote Pairing
The vehicle siren will chirp. You have now successfully learned the remote to the vehicle remote start and security system. Press the button two times to exit learn routine on the remote. The transmit LED will turn off and exit tone will sound. © 2009 Directed Electronics. All rights reserved. -
Page 11: Programming System Features
The learn routine exits if any of the following occurs: • The open door is closed • The ignition is turned On • There is no activity for 30 seconds • The Control button is pressed too many times © 2009 Directed Electronics. All rights reserved. -
Page 12: Feature Menus
On w/Warn Chirps Off: arm and disarm chirps are active, warn-away chirps are defeated Off w/Warn Chirps On: arm and disarm chirps are defeated, warn-away chirps are active Off w/Warn Chirps Off: arm, disarm, and sensor warn-away chirps are defeated © 2009 Directed Electronics. All rights reserved. - Page 13 15. Remote Button Unlock (Ign off) On: a message telling the 2-way remote control to unlock the keypad is sent each time the vehicle ignition is turned off Off: no message is sent © 2009 Directed Electronics. All rights reserved.
-
Page 14: Menu 2 - Convenience
On: the dome light output will activate when the ignition is turned off Off: the dome light output will not activate when the ignition is turned off 6. OEM Alarm Disarm w/Aux/Trunk (H2/1 wire) © 2009 Directed Electronics. All rights reserved. - Page 15 15. Aux 4 Output Type • Refer to Aux 1 Output Type descriptions 16. Aux 4 Linking • Refer to Aux 1 Linking descriptions 17. Aux/Trunk Output Type • Refer to Aux 1 Output Type descriptions © 2009 Directed Electronics. All rights reserved.
-
Page 16: Menu 3 - Remote Start
Menu 3 - Remote start Menu Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+ Item Transmission Mode Automatic Manual Engine Checking Mode Virtual Tach Voltage Tachometer Cranking Time 0.6 sec. 0.8 sec. 1.0 sec. 1.2 sec. 1.4 (5)/ 1.6 (6)/ 1.8 (7) 2.0 (8)/ 4.0 Remote Start Runtime... - Page 17 On: the report is sent every 2 minutes during remote start if the temperature has changed (+/-) 1 degree since the last report 16. Remote start Safelock Off: the Door lock and Factory Alarm Re-arm outputs will maintain the current status (locked/un- © 2009 Directed Electronics. All rights reserved.
-
Page 18: Bitwriter - Only Options
Unlocked Locked Transmitter Programming Locked Unlocked Remote Start Runtime 12 min. Options: 1 to 60 min. Virtual Tach Fine tune Not Initial- Options: Not initialized, 0 to 1000 in 50 millisecond increments ized © 2009 Directed Electronics. All rights reserved. - Page 19 Remote Start Runtime: sets the duration of runtime when the engine is started by remote command VirtualTach Fine tune: adds or subtracts crank time in VirtualTach mode in order to overcome engine types that short crank or over-crank on the first start attempt © 2009 Directed Electronics. All rights reserved.
-
Page 20: Basic Remote Functions
1 minute or until the ignition is turned off. Refer to table of zones. Note: The Warn Away triggers are not stored to memory and is not reported. © 2009 Directed Electronics. All rights reserved. -
Page 21: Table Of Zones
Reducing the sensitivity can solve this problem. Door locks operate backwards. • This unit has easily-reversed lock/unlock outputs. Recheck wire connections to see if you have re- versed these. © 2009 Directed Electronics. All rights reserved. -
Page 22: Troubleshooting: Remote Start
Is an ignition or accessory output wire connected to the starter wire of the vehicle? Verify the color of the starter wire in the vehicle and confirm that an ignition or an accessory output is not connected to that wire. The vehicle starts, but will only run for 10 seconds © 2009 Directed Electronics. All rights reserved. - Page 23 • The E-brake wire connected to the neutral safety input of the system has a poor ground. Clean the contacts on the switch or replace the switch. © 2009 Directed Electronics. All rights reserved.